American Standard 2771EC User Manual

CADET ELITE™ 5’ x 36”

WHIRLPOOLS BY AMERICAN STANDARD

HIGH GLOSS ACRYLIC

CADET ELITE™ 5’ X 36” WHIRLPOOL

Comfortable bathing design with form-fitted backrest and molded-in armrests

❏ 2771E (specify White 020, Bone 021, or

Linen 222)

• Acrylic with fiberglass reinforcement

• 1.5 HP self-draining pump/motor

with dry run seal

• Eight multi-directional and flow adjustable jets including: Two high performance Ideal-flow™ Jets Six interchangeable Flex-jets™

• Two silent air volume controls

• Deck-mounted On/Off control

• Complete factory installed and tested

whirlpool system

❏ 2771EC (specify White 020, Bone 021, or

Linen 222)

• Same as above with the StayClean™ whirlpool system featuring Antimicrobial AlphaSan®

Nominal Dimensions: 60” x 36” x 19-3/4" (1524 x 914 x 502mm)

HD-014

SPS 2771E

Revised 6/03

Compliance Certifications Meets or Exceeds the Following Specifications:

• Underwriters Laboratories - Hydromassage Bathtubs UL 1795

• ASME A112.19.7M for Whirlpool Appliances

• ANSI Z124.1 for Plastic Bathtubs

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

* See American Standard Faucet Selector

NOTE: Roughing-in dimensions and product specifications shown on reverse side of page.

Components Needed:

❏ Bath Filler*: (specify finish) ❏ Bath Drain: BATH-DRAIN

(specify Chrome 002, Polished Brass 099,

or Satin 295)

Custom Accessories Available:

❏ Pulse Jet Kit: PULSE-JET (two per kit,

specify White 020, Bone 021, or Linen 222)

❏ Soft Jet Kit: SOFT-JET (two per kit, specify

White 020, Bone 021, or Linen 222)

❏ Five Foot Apron: 5FT-APRON (specify White

020, Bone 021, or Linen 222)

❏ E-Z-Install™ Whirlpool Heater - EZHEAT-100 ❏ Tile Bead Kit: TILE-BEAD

NOTE: E-Z-Install™ Whirlpool Heater is designed to maintain water temperature during operation. It will not heat cold water to desired bathing temperature.

CADET ELITE™ 5’ x 36”

WHIRLPOOLS BY AMERICAN STANDARD

HIGH GLOSS ACRYLIC

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUPPORT OF BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.

REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION. OPTIONAL 3 WALL TILING BEAD. KIT No. TILE-BEAD AND APRON No. 5FT-APRON AVAILABLE AND MUST BE

ORDERED SEPARATELY. FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

IMPORTANT:

Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

■

EE FITTING

SERVICING ON ALL INSTALLATIONS

PECS FOR

IMENSIONS

914 mm

(36)

235 mm

(9-1/4)

FINISHED

457 mm

(18)

19 mm

WALL

(3/4)

305 mm

(12)

1524 mm

RECOMMENDED FITTING LOCATION

229 mm

(9)

CUTOUT IN FLOOR FOR DRAIN

(60)

64 X 330mm (2-1/2 x 13")

FOR PIER OR ISLAND

INSTALLATIONS ONLY

PUMP

ON/OFF SWITCH

C/L OF

SUPPLIES

OPTIONAL TO

FINISHED FLOOR

USUALLY BETWEEN

1651 & 1981mm

(65 & 78)

57 mm (2-1/4)

C/L OF DRAIN

C/L OF OVERFLOW

67mm (2-5/8)

502 mm (19-3/4)

ROUGH

FLOOR

INTEGRAL

SUPPORT

FEET

GENERAL SPECIFICATIONS FOR 2771E WHIRLPOOL

INSTALLED SIZE

WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW MIN. OPERATING GAL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS.

CUBE (FT3)

WHIRLPOOL ELECTRICAL SPECIFICATIONS

(8) JETS

38 mm (1-1/2)

305 mm

1-1/2 N.P.T.M.

1-1/2 O.D.TAILPIECE

(2) AIR VALVES

ALT. FITTING

(12)

102 mm

THREADS

LOCATION #1

(4)

C/L OF SHOWER ARM

C/L OF VALVES

C/L OF SPOUT

SAFE-T- HEATER REMOVABLE BLANK

70 mm (2-3/4)

117 mm

(4-5/8)

60 x 36 x 19-3/4 In.

(1524mm x 914 mm x 502mm)

95 Lbs. (43 Kg.)

587 Lbs. (267 Kg.)

59 Gal. (224 L.)

48 Gal. (182 L.) 40 x 22 In. (1016mm x 559mm) 52 x 29 In. (1321mm x 737mm)

13-1/4 In. (337mm)

39 Lbs./Sq. Ft. (188 Kgs/Sq. m.)

1.6 HP, 9.7 AMPS, 120V.PUMP

OUTLINE OF CUTOUT 1486 mm x 876 mm (58-1/2 X 34-1/2)

■ LEVELING STRINGER

NOT FOR

SUPPORT

464 mm (18-1/4)

23.8

44.5