American Standard 2771E User Manual
CADET ELITE™
5' x 36"
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
305 mm
RECOMMENDED FITTING LOCATION
(3/4)
(12)
57 mm
(2-1/4)
C/L OF
OVERFLOW
76 mm
(3)
ROUGH
FLOOR
INTEGRAL
SUPPORT
229 mm
CUTOUT IN FLOOR
FOR DRAIN
C/L OF DRAIN
38 mm
(1-1/2)
502 mm
(19-3/4)
FEET
1-1/2 O.D.TAILPIECE
235 mm
(9-1/4)
SEE FITTING
SPECS FOR
DIMENSIONS
914 mm
(36)
SUPPLIES
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
FINISHED
WALL
457 mm
(18)
C/L OF
(65 & 78)
19 mm
(9)
(8) JETS
305 mm
1-1/2 N.P.T.M.
(12)
THREADS
2771E SERIES
WHIRLPOOL/BATHING POOL
INSTALLATION INSTRUCTIONS
PROVIDE ACCESS TO PUMP FOR
SERVICING ON ALL INSTALLATIONS
1524 mm
(60)
64 X 330mm (2-1/2 x 13")
FOR PIER OR ISLAND
INSTALLATIONS ONLY
PUMP
(2) AIR VALVES
ALT. FITTING
LOCATION #1
C/L OF
SHOWER ARM
C/L OF
VALVES
C/L OF
SPOUT
(4)
IN-LINE HEATER
REMOVABLE
BLANK
70 mm
(2-3/4)
102 mm
OUTLINE OF CUTOUT
1486 mm x 876 mm
(58-1/2 X 34-1/2)
464 mm
(18-1/4)
117 mm
(4-5/8)
■ LEVELING
STRINGER
NOT FOR
SUPPORT
ON/OFF
SWITCH
THANK YOU...
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
List of Optional Components (not included):
• Flex-Jet Pulse Jet Kit*
• Flex-Jet Soft Jet Kit*
• E-Z-Install Heater*
• Tile Bead Kit*
• Apron Kit*
List of Required Components (not included):
• Drain* • Bath Filler*
* see your Home Depot Retailer
GENERAL SPECIFICATIONS FOR 2771E WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
MIN. OPERATING GAL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
40 x 22 In. (1016mm x 559mm)
52 x 29 In. (1321mm x 737mm)
39 Lbs./Sq. Ft. (188 Kgs/Sq. m.)
60 x 36 x 19-3/4 In.
(1524mm x 914 mm x 502mm)
95 Lbs. (43 Kg.)
587 Lbs. (267 Kg.)
59 Gal. (224 L.)
48 Gal. (182 L.)
13-1/4 In. (337mm)
1.6 HP, 9.7 AMPS, 120V.PUMP
23.8
44.5
List of Required Tools and Supplies:
Supplies
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 amp GFI
Outlet
• Cement, Plaster,
Grout
• Caulking Gun
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
752860-100 Rev. B
© American Standard Inc. 2002
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
INSTALLATION AND FRAMING INSTRUCTIONS
The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs
as required. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an
access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for
access to the drain components.
NOTE: The apron should not be used as the primary access opening.
1. Position the whirlpool into the installation opening and level the deck, shimming the integral support feet as necessary.
Mark the final position of the underside of the deck by tracing a line on to the studs (see Figure 1).
2. Remove the whirlpool and attach a 2 x 4 stringer to the studs, with the top of the stringer touching the traced line.
3. Install drain components to the whirlpool following the manufacturers instructions. Before replacing your whirlpool for final
installation, be certain that an opening has been provided in the sub-floor for the drain. See the roughing-in drawing for
suggested opening size and location dimensions.
4. Replace whirlpool and re-shim the integral support feet, shimming the entire length of the support feet. Secure the shims
using construction adhesive, silicone, mortar or equivalent materials. While not a necessity, the use of a foundation base
consisting of cement (e.g. Sakrete), mortar, or grout will help provide a solid and secure installation.
FIG. 1
464mm
(18-1/4)
TYPICAL RECESS INSTALLATION
TILE
WALLBOARD
TILE
BEAD
STRIP
SEALANT
BATH
ADHESIVE
LEVELING
STRINGER
NOTE: Tile bead kit not included and must be
purchased separately.
TYPICAL PIER TYPE INSTALLATION
AS DESIRED
876 mm
464mm
(18-1/4)
(34-1/2)
CUTOUT
1486mm
(58-1/2)
CUTOUT
464mm
(18-1/4)
1527mm
(60-1/8)
UNLESS AN ACCESS OPENING OF AT LEAST
12" X 24" (305 X 610MM) IS PROVIDED,
WARRANTY SERVICE WILL NOT BE PERFORMED.
876mm
(34-1/2)
914mm
(36)
TUB WIDTH
LEVELING
STRINGERS
WHIRLPOOL ONLY:
610mm
(24)
305mm
(12)
752860-100 Rev. B (2)
LEVELING
SURFACE
WARRANTY SERVICE WILL NOT BE PERFORMED.
AS DESIRED
WATERPROOF
SEALANT
BATH
UNLESS AN ACCESS OPENING OF AT LEAST
12" X 24" (305 X 610MM) IS PROVIDED,
WHIRLPOOL ONLY:
ACCESS PANEL
610mm
(24)
305mm
(12)
Loading...