American Standard 2770.712, 2770.702, 2770.732 User Manual
Installation
Instructions
2770.732 SERIES
BAR SINK FAUCETS
with EverClean™ Finish
Congratulations on purchasing your American Standard
faucet with EverClean finish found only on American
Standard faucets.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
2770.712 SERIES
2770.702 SERIES
Certified to comply with ANSI A112.18.1M
U.S. Patent No. 5,819,789
.3&7
SPOUT
AERATOR
SPOUT
CLIP
O-RING
INDEX
CAP
PORCELAIN
CROSS
HANDLE
HANDLE
(CROSS HANDLE)
BASE
CARTRIDGE
ESCUTCHEON
HANDLE
SCREW
HANDLE
SCREW
ADAPTER
INDEX CAP
HANDLE
BASE
PORCELAIN
LEVER
HANDLE
END
CAP
METAL
LEVER
HANDLE
PUTTY
PLATE
LOCKNUT
SUPPLY
NUT
For toll-free information and answers to your questions, call:
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 1998
HOT LINE FOR HELP
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN MEXICO 01-800-839-12-00
Weekdays 8:00 a.m. to 7:00 p.m. EST
INSTALL FAUCET
1
CAUTION
Turn off hot and cold water supplies before beginning.
Place faucet in position on sink.
Assemble and tighten LOCKNUTS from underside of SINK.
Connect the HOT water supply to the left SHANK and the
COLD water supply to the right SHANK using appropriate
connectors and sealant (not supplied), and COUPLING NUTS.
BODY
PUTTY
PLATE
SINK
LOCKNUT
TEST INSTALLED FAUCET
2
Remove AERATOR.
With handles in OFF position, turn on water supplies and check all connections for leaks.
Operate both handles to flush water lines thoroughly.
Turn handles into OFF position and replace AERATOR.
HOT
SHANK
COLD
NOT SUPPLIED
COUPLING NUT
SERVICE Handle alignment.
3
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP and remove
HANDLE SCREW.
Pull off HANDLE BASE and remove
ADAPTER.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90$ and replace.
Replace SPRING CLIP.
Reinstall HANDLE.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90$.
EverClean™ Finish Care Instructions
4
STOP
WASHER
90$
SPRING
CLIP
Check alignment, if not satisfactory
aligned;
Push out ADAPTER carefully.
Turn ADAPTER either 45˚ or 90˚
so that male square on
ADAPTER catches different
female square in HANDLE BASE.
Assemble and tighten
MOUNTING SCREW.
Push INDEX CAP in top of
HANDLE.
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with
clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
FEMALE SQUARE
IN HANDLE BASE
HANDLE
ADAPTER
SQUARE
VALV E
STEM
.3&7
Loading...