American Standard 2742.XXXX User Manual
TOWN SQUARE®
INSTALLATION
6' x 42"™
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
INSTRUCTIONS
2742.XXXX SERIES WHIRLPOOL / BATHING POOL
THANK YOU...
for selecting an American Standard bath. Your
new bath is shipped to you after careful
4"
(102mm)
13-1/4"
(337mm)
41-3/4"
(1060mm)
3/4"
(19mm)
2"
(51mm)
INTEGRAL
FEET
SUPPORT
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
C/L OF DRAIN OUTLET
SAFE-THEATER
REMOVABLE
BLANK
GENERAL SPECIFICATIONS FOR 2742 WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
71-1/2"
35-3/4"
(908mm)
26-3/4
(679mm)
SUCTION
PUMP
1-1/2" N.P.T. THREADS
1-1/2" O.D.TAILPIECE
71-1/2 x 41-3/4 x 22 In. (1816 x 1060 x 559mm)
(1816mm)
FLOOR CUTOUT
5" X 15"
(127 X 381mm)
LEVELING STRINGER
(NOT FOR SUPPORT)
41 x 21-1/2 In. (1041 x 546mm)
62 x 31-1/2 In. (1574 x 800mm)
33 Lbs./Sq.Ft. (163 Kgs./Sq.m)
INTEGRAL
FITTING DECK
3" X 14"
(76 X 356mm)
ROUGH
5/8"
(16mm)
690 Lbs. (313 Kg.)
14-1/4 In. (362mm)
2.1 HP, 14.4 AMPS ,120V.WHIRLPOOL PUMP
(83mm)
FLOOR
115 Lbs. (52 Kg.)
JETS (8)
3-1/4"
(508mm)
3"
(76mm)
69 Gal. (261 L)
60 Gal. (227 L)
27.8
55.7
3"
(76mm)
EDGE OF
FLOOR
CUTOUT
PROVIDE ACCESS
TO PUMP FOR
SERVICE ON ALL
INSTALLATIONS
PUMP
ON/OFF
SWITCH
OUTLINE OF CUTOUT
70" X 40-1/4"
(1778 X 1022mm)
C/L OF
OVERFLOW
22"
(559mm)
20"
inspection. The whirlpool version is completely
assembled with pump, motor, and system
piping. All you need to finish the installation
are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure
from this product, please follow the
instructions and cautions.
List of Optional Components (not included):
• Safe-T-Heater 9075.120*
List of Required Components (not included):
• Drain 1594.170
• Bath Filler
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for
any shipping damage. If such damage is found,
report it to your vendor immediately.
After inspection and during installation, protect
the bath from construction damage. After
installation, and before enclosing with wallboard,
tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool
system or remove pump from factory mounting.
This could adversely affect the safety and
performance of the whirlpool and void the
warranty. Do not handle or move the whirlpool by
the pump, motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not
provided with the bath and must be ordered
separately. Framing and enclosing materials are
provided by others.
Protect all finished surfaces of the whirlpool
during construction and installation using a drop
cloth.
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 20 amp GFI Outlet
• Cement, Plaster,
Grout
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
753027-100 REV. F
WARNING! Do not lift whirlpool by the piping
harness at any time.
© AS America Inc. 2009
All product names listed herein are trademarks
of AS America Inc. unless otherwise noted.
INSTALLATION AND FRAMING INSTRUCTIONS
The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs
as required. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an
access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for
access to the drain components.
1. Position the whirlpool into the installation opening and level the deck, shimming the integral support feet as necessary.
2. Install drain components to the whirlpool following the manufacturers instructions. Before replacing your whirlpool for final
installation, be certain that an opening has been provided in the sub-floor for the drain. See the roughing-in drawing for
suggested opening size and location dimensions.
3. Replace whirlpool and re-shim the integral support feet, shimming the entire length of the support feet. Secure the shims
using construction adhesive, silicone, mortar or equivalent materials. While not a necessity, the use of a foundation base
consisting of cement (e.g. Sakrete), mortar, or grout will help provide a solid and secure installation.
TYPICAL PIER TYPE INSTALLATION
AS DESIRED
1022mm
(40-1/4)
1778mm
(70)
CUTOUT
508mm
(20)
305mm
(12)
AS
DESIRED
LEVELING
SURFACE
WATERPROOF
SEALANT
ACCESS PANEL
BATH
UNLESS AN ACCESS OPENING OF
AT LEAST 12" X 24" (305 X 610MM)
IS PROVIDED, WARRANTY SERVICE
WILL NOT BE PERFORMED.
610mm
(24)
753027-100 REV. F
(2)
Loading...