American Standard 2732.002, 2732.018 User Manual

RENAISSANCE™ WHIRLPOOL AND BATHING POOL

Comfortable bathing design with form-tted backrest and molded-in armrests

❏ 2732.018 Whirlpool featuring System I

• Acrylic with berglass reinforcement

• Factory installed and tested whirlpool system

• 1.25 HP single speed, self-draining pump/motor

• Factory-installed power cord with plug

• Six multi-directional color-coordinated jets including two in back rest area

• One color-coordinated air volume control

• Deck-mounted, color-coordinated air switch On/Off control

• Dual, molded-in arm rests

❏ 2732.002 Bathing Pool Only

Nominal Dimensions:

1524 x 832 x 502mm (60" x 32-3/4" x 19-3/4")

RENAISSANCE™ WHIRLPOOL

AND BATHING POOL

HIGH GLOSS

Compliance Certications Meets or Exceeds the Following Specications:

• Underwriters Laboratories - Hydromassage Bathtubs UL 1795

• ASME A112.19.7M for Whirlpool Appliances

• ANSI Z124.1 for Plastic Bathtubs

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

SEE REVERSE FOR PRODUCT DIMENSIONS AND SPECIFICATIONS

To Be Specied - Required:

❏ Bath Filler: (specify nish) ❏ Bath Drain: 1583.470 (specify nish)

To Be Specied - Optional:

❏ 5 Foot Apron: 9260.018 (specify color) ❏ Universal Tile Bead Kit: 751755-100 ❏ Grab Bar Kit: 9822.200-two per kit (specify nish)

For color/nish availability and other faucet choices, please see the Product Selector and Pricing Guide.

H67

Revised 2/08

RENAISSANCE™ WHIRLPOOL

60"

(1524mm)

33"

(838mm)

5-7/8"

(149mm)

12"

(305mm)

(152mm)

(76mm)

8-1/2"

(216mm)

16-1/2"

(419mm)

33"

(838mm)

19-3/4"(H)

(502mm)

18-1/4"(C)

(464mm)

C/L OF OVERFLOW

16-1/2"

(419mm)

CUT OUT IN FLOOR

FOR DRAIN

DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCES ESTABLISHED BY ANSI STANDARDS Z124.1 AND A112.19.7.

60 x 3 2- 3/ 4 x 19 -3 /4 I n.

(1524 x 83 2 x 50 2m m)

65 Lbs. (2 9 Kg .)

524 Lbs. ( 23 7 Kg .)

55 Gal. ( 20 8 L. )

41 Gal. ( 15 5L .)

40-1/2 x 2 0- 1/ 2 In .

(1029mm x 52 1m m)

52-1/2 x 26-1/2 In. (1334mm x 673mm)

13-3/4 I n. ( 34 9m m)

38 Lbs. /S q. F t. ( 18 7 Kg s/Sq. m.)

GENERA L SPEC IFICA TIONS FOR 2732 WH IRLPOO L

INSTALLE D SI ZE

WEIGHT WEIGHT w /W AT ER GAL. TO OV ER FL OW MIN. OPE RA TI NG G AL . BATHING WE LL A T SU MP

BATHING WE LL A T RI M WATER DE PT H TO O VE RF LO W FLOOR LO AD IN G (PROJECT ED A RE A)

WHIRLP OOL EL ECTRI CAL SP ECIFICATION S

1.25 HP, 9 .7 A MP S, 1 20 V.PUMP

60 x 32-3/4 x 19-3/4

(1524 x 832 x 502mm)

GENERAL SPECIFICATIONS FOR 2732 BATHING POOL

51 Lbs. (23 Kg.)

509 Lbs. (230 Kg.)

55 Gal. (208 L.)

40-1/2 x 20-1/2 In. (1029 x 521mm)

52-1/2 x 26-1/2 In. (1334 x 673mm)

13-3/4 (349mm)

37 Lbs./Sq.Ft. (182 Kgs./Sq.m)

INSTAL LED SI ZE

WEIGHT WEIGHT w/WAT ER GAL. T O OVER FLOW BATHIN G WELL AT SU MP BATHIN G WELL AT RI M WATER DEPTH TO OVE RFLOW FLOOR LOADIN G

(PROJE CTED A REA)

AND BATHING POOL

HIGH GLOSS

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUPPORT OF BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.

■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.

OPTIONAL 3 WALL TILING BEAD. KIT AND APRON No.9260.018 AVAILABLE AND MUST BE ORDERED SEPARATELY.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

H68

Revised 2/08