Page 1
Installation Instructions
ROPE TWIST™ BATHING POOL
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
MODELS: 2722.102 RHO
2722.202 LHO
USED WITH BATH WALLS: 5030.LBW
Thank you for selecting American-Standard...the benchmark of fine quality
for over 100 years. To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
BEFORE YOU BEGIN....
Local building codes vary by location. Observe all local plumbing and building codes.
Your new bath is shipped to you after careful inspection. All you need to finish the installation are your selected fittings.
To insure maximum performance and pleasure from this product, please follow the instructions and cautions.
GENERAL INSTALLATION INFORMATION ....
1. WHEN INSTALLING THE MATCHING ROPE TWIST BATH WALLS (MODEL 5030.LBW),
ADDITIONAL STUDS MAY BE REQUIRED. REFER TO THOSE INSTALLATION INSTRUCTIONS
PRIOR TO INSTALLING TUB.
754049-100 Rev. G
2. ROPE TWIST SHOWER WALLS ARE TO BE INSTALLED OVER STUD WALLS.
3. BATH MAY ONLY BE INSTALLED IN A RECESS TYPE INSTALLAION.
4. THIS BATH IS NOT SELF-SUPPORTING AND MUST BE SUPPORTED ALONG ITS ENTIRE
BOTTOM WITH MORTAR OR GROUT. STRINGERS WILL HELP LEVEL TUB, BUT WILL NOT
PROVIDE ADEQUATE SUPPORT.
5. TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE BATH.
TOOLS & MATERIALS REQUIRED....
TOOLS:
• Level
• Square
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard Woodworking Tools
• Personal Safety Equipment
• Caulking Gun
NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.
MATERIALS:
• Nails
• Plumber’s Putty
• Silicone Sealant
• 1 x 3 or 2 x 4 Stringers
• Drop Cloth
• Mortar Mix or Grout (1 bag)
FOR TOLL FREE INFORMATION AND ANSWERS TO YOUR QUESTIONS, CALL:
© AS America, Inc. 2008
All product names listed herein are trademarks
of AS America, Inc. unless otherwise noted.
HOTLINE FOR HELP
1 (800) 442-1902, in Canada call 1 (800) 387-0369.
Weekdays 8:00 a.m. to 4:00 p.m. Eastern time.
1
Page 2
ROUGH-IN INFORMATION:
GENERAL SPECIFICATIONS FOR 2722 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
22 x 44 In. (559 x 1118mm)
25.5 X 53 In.(648 x 1346mm)
29 Lbs./Sq.Ft. (195 Kgs/Sq.m)
60 x 32 x 17 In.
(1524 x 813 x 432mm)
60 Lbs. (27 Kg)
393 Lbs.(179 Kg)
10 In. (254mm)
40 Gal. (151 L)
15.3
27
(19mm)
15-1/8"
(385mm)
32"
(813mm)
3/4"
9-3/8"
(238mm)
60"
(1524mm)
FINISHED
WALL
229mm x 305mm
(9 x 12)
FLOOR
CUTOUT
70mm
(2-3/4)
INSTALLATION AND FRAMING INSTRUCTIONS:
1
TOP OF
DECK
(432mm)
25mm
(1)
1"
(25mm)
17"
4-5/8"
(117mm)
BATH SUPPORT
MATERIAL
C/L OF
DRAIN
4-1/2"
(114mm)
3-1/2"
(89mm)
1-1/2 N.P.T. THREADS
1-1/2 O.D. TAILPIECE
SEE
NOTE
FINISHED
WALL
2"
(51mm)
16-3/4"
(425mm)
ROUGH
FLOOR
A.) Locate studs as required. Ensure roughing-in dimensions are proper, plumb, and square. It is strongly recommended that an additional
opening be provided for access to the drain components.
Illustration 1
Each alcove
stud must
be plumb
and square.
B.) As shown in ILL. 2, mark the position of the underside of the deck by tracing a line onto the studs at the height indicated, using a level or
other suitable straight edge.
C.) With the top of the stringer touching the traced line, attach the stringer to the studs.
Illustration 2
16-3/4
(425mm)
D.) Install drain components to the bath following the manufacturer's instructions. See the roughing-in drawing for suggested opening size and
location dimensions.
30
762mm)
(
2
754049-100 Rev. G
Page 3
2
A.) THIS BATH MUST BE SUPPORTED ALONG IT'S ENTIRE BOTTOM. We recommend the use of mortar as bedding material (sand is not
recommended). Apply enough bedding to support the complete bottom of the bath. After the bedding has been poured, and before it sets,
position the bath within the recess until the rim is leveled against the leveling stringers (see "Typical Recess Installation") shown below. The rim
of the bath MUST NOT support weight. Allow the bedding material to completely harden before applying weight to the rim or bottom of the bath.
TYPICAL RECESS INSTALLATION
32
3mm)
81
IDTH
(
W
60-3/16
(1529mm)
B.) Check level front to back and side to side, shim as necessary. To secure the tub to wood studs, use drywall screws with flatwashers or
roofing nails immediately above the flange of the bath. To secure the tub to steel studs, use 4" drywall screws and flatwashers.
TUB
LEVELING
STRINGERS
34 Typ.
(864mm)
TYPICAL FLANGE MOUNTING DETAIL
SUGGESTED BATH
INSTALLATION METHOD
WOOD
STUDS
WATERPROOF DRYWALL
OR CEMENT BOARD
STEEL
STUDS
WATERPROOF DRYWALL
OR CEMENT BOARD
TILE
SEALANT
TUB
STUD
TILE
ROOFING NAIL
SEALANT
TUB
1 x 3 (25 x 76mm) WOOD
STRINGER FULL LENGTH
STEEL
STUD
WASHER
4" (102mm)
DRYWALL
SCREW
1 x 3 (25 x 76mm) WOOD
STRINGER FULL LENGTH
SECURE THE BATH TO THE STUDS AS SHOWN
FOR WOOD OR STEEL STUD CONSTRUCTION.
C.) Any finish material such as tile or wallboard must be self-supporting if it contacts the deck of the bath.
Flooring will be butted against the bottom of the tub apron, also holding the tub in place.
3
754049-100 Rev. G
Page 4
3
DRAIN CONNECTION
Using recommended drain opening, connect bath drain to waste line. Tighten all drain joints securely.
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use wire
brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may be
removed using granular Spic and Span® mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
FEATURES of YOUR NEW AMERICAN STANDARD ACRYLIC BATHTUB
Your new acrylic bathtub has been molded in the newest plumbing fixture material available today. Acrylics are tough durable finishes that
are simple and easy to care for.
The colors have been formulated to match other American-Standard fixtures and enhance your choice of bathroom decorations. The high
gloss surface is resistant to impact and chemicals and will retain its lasting luster with proper care and maintenance.
AFTERCARE and CLEANING
• Always fill the tub with temperate water. Excessively hot water may cause surface damage
• Remove bath mat after use and hang to dry. Allowing bath mat to dry in the tub may cause surface damage.
• Clean after use with a mild liquid household detergent cleaner. Abrasive cleaners such as Lestoil, Lysol Disinfectant (spray or concentrate),
or Lysol Basin, Tub and Tile Cleaner, Windex, Mr. Clean, Dow Disinfectant Bathroom Cleaner, or cleaning products in aerosol cans should
not be used.
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.
• Do not use wire brushes, knives or sharp objects to remove stains, cigarette tar deposits, or other surface blemishes.
• Abrasive cleaners or powders must not be used, since they will dull the surface. If the glossy surface looses its sheen, dulled areas can be
restored by rubbing with a white polishing compound and waxing with a "liquid wax."
• Do not wax areas where you walk or stand.
• Do not allow nail polish remover, acetone, dry cleaning fluid, paint remover or other solvents to come into contact with the surface.
• Clean the surrounding surface immediately after using caustic drain cleaners.
• Burning cigarettes will damage the surface.
• Should damage to the fixture occur, repairs can be made quickly and easily. Your distributor or builder can provide details.
SPIC AND SPAN® IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE
4
754049-100 Rev. G
Page 5
AS America, Inc. Limited Lifetime Warranty for Rope Twist™ Bathing Pools
AS America, Inc. (”American Standard”) warrants to the original consumer purchaser that it will, at its option, repair or replace this bathing pool – American
Standard, in its sole judgment, to be defective under normal residential use and maintenance so long as it is owned by the original consumer purchaser.
To activate this limited warranty, the purchaser must go online to our website at www.americanstandard-us.com/warranty to register their bathing pool, or the
accompanying warranty registration card must be completed and returned to the address on the warranty registration card within thirty (30) days of purchase.
In no event will American Standard be liable for the cost of repair or replacement of any installation materials including but not limited to tile, marble, etc.
This limited warranty does not apply to Commercial Installations. The warranty for Commercial Installations is three (3) years.
This limited warranty DOES NOT COVER the following:
1. Defect or damages arising from shipping, installation, alterations, accidents, abuse, misuse, lack of proper maintenance and cleaning as directed in the
Installation Instruction Manual and use of other than genuine American Standard replacement parts, in all cases whether caused by a plumbing contractor,
service company, the owner or any other person.
2. Deterioration through normal wear and tear and the expense of normal maintenance.
3. Commercial application.
4. Options and accessories. American Standard's limited warranty on these items is one year for parts only and excludes labor. This one year limited
warranty covers accessories manufactured by American Standard (e.g. aprons, drains, grab bars, heaters, trim kits) against defects of material or
workmanship. Warranty coverage begins on the date the accessory was originally purchased by the owner.
5. Shipping cost for returning products for repairs or replacement under the limited warranty and labor or other cost incurred in connection with product removal
or installation under this limited warranty.
6. ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, ALL OF WHICH ARE HEREBY EXPRESSLY DISCLAIMED, OR THE EXTENSION
BEYOND THE DURATION OF THIS LIMITED WARRANTY OF ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY OR FITNESS
FOR AN INTENDED PURPOSE. (Some jurisdictions do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental
or consequential damages, so these limitations and exclusions may not apply to you.)
7. Responsibility for compliance with local code requirements. (Since local code requirements vary greatly, distributors, retailers, dealers, installation
contractors and users of plumbing products should determine whether there are any code restrictions on the installation or use of a specific product.)
This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case
this warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a
service request (including a description of the product model and of the defect) be sent to the following address:
In the United States:
American Standard
P.O. Box 659
West Caldwell, NJ 07007
Attention: Customer Care
For residents of the United States, warranty
information may be obtained by calling the
following toll free number (800) 442-1902
In Canada:
American Standard
2480 Stanfield Road
Missassauga, Ontario
Canada L4Y 1S2
In Mexico:
Customer Service Manager
Ideal Standard S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
PLEASE DO NOT DISREGARD AMERICAN STANDARD WARRANTY REGISTRATION CARD
Registration must be completed within thirty (30) days from purchase in order for this warranty to become effective. Please
visit our website at www.americanstandard-us.com/warranty to register your product online. If you choose to register by mail,
this card must be completed and returned to the address printed on this card within thirty (30) days from date of purchase in
order for this warranty to become effective.
This warranty is not transferable from original consumer purchaser.
American Standard Limited Lifetime Warranty Registration Card
Purchaser's Name:
Purchaser's Address:
Phone (optional):
Email address:
Store / Purchase location:
Example: Home Town Plumbing Supply
543 Main Street
Anytown, NJ 12345
Today's Date:
Product Purchased Date:
Model Name:
Model Number:
Copyright and trademarks are property of American Standard Inc.
5
754049-100 Rev. G
Loading...