American Standard 2709.XXXW User Manual
ELLISSE OVAL™
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
240 mm
(9-7/16)
SEE FTTG.SPECS
FOR DIMENSION
OF SUPPLIES
C
L
978 mm
(38-1/2)
489mm
(19-1/4)
76mm
(3)
OF DRAIN
C
L
OUTLET
REMOVABLE BLANK
86mm
(3-3/8)
38mm
(1-1/2)
502mm
(19-3/4 )
464mm
(18-1/4)
SAFE-T-HEATER
305mm
(12)
C/L OF
VALVES
102mm
(4)
1-1/2 N.P.T.M.
THREADS
1-1/2 O.D.
TAILPIECE
2709.XXXW SERIES
WHIRLPOOL/BATHING POOL
INSTALLATION INSTRUCTIONS
1759 mm
(69-1/4)
ON/OFF
SWITCH
305mm(12) X 229 mm(9)
CUTOUT IN FLOOR FOR DRAIN
SHOWER ARM
C/L OF
SPOUT
INTEGRAL
FEET
SUPPORT
35mm
(1-3/8)
▲OUTLINE OF
CUTOUT
C/L OF
ROUGH
FLOOR
98mm
(3-7/8)
PUMP
PROVIDE ACCESS
TO PUMP FOR
SERVICING ON ALL
INSTALLATIONS
1651-1981mm
(65-78)
OPTIONAL
THANK YOU...
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
List of Optional Components (not included):
• Safe-T-Heater 9075.120*
* see your American Standard Distributor
List of Required Components (not included):
• Drain 1583.470*
• Bath Filler*
* see your American Standard Distributor
GENERAL SPECIFICATIONS FOR 2709 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
SYSTEM I PUMP
SYSTEM II PUMP
SAFETY HEATER ________________________________12 AMPS, 120V.
WHIRLPOOL ELECTRICAL SPECIFICATIONS
69-1/4 x 38-1/2 x 19-3/4 In.(1759 x 978 x 502mm)
35 Lbs./Sq.Ft. (166 Kgs./Sq.m)
107 Lbs. (49 Kg.)
640 Lbs. (291 Kg.)
64 Gal. (243 L)
45 x 23 In. (1143 x 584mm)
63 x 32 In. (1600 x 813mm)
53 Gal. (201 L)
13 In. (330mm)
25.6
49.4
2.1 HP, 14.4 AMPS, 120V.
2.1 HP, 15.6 AMPS, 120V.
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 20 amp GFCI
Outlet
• Cement, Plaster,
Grout
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
751753-100 Rev.J
© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
FRAMING AND INSTALLATION
THE VARIETY OF INSTALLATIONS POSSIBLE FOR THIS BATH MAY REQUIRE FRAMING PROCEDURES OTHER THAN THOSE SHOWN.
LOCATE STUDS AS REQUIRED. INSURE ROUGH DIMENSIONS ARE PROPER, PLUMB AND SQUARE. FOR WHIRLPOOLS, PROVISION MUST
BE MADE IN ALL INSTALLATIONS FOR AN ACCESS OPENING FOR SERVICING PUMP AND CONTROLS.
THE FOLLOWING PROCEDURE MUST BE USED FOR ALL INSTALLATIONS: STRINGER OR PIER HEIGHT SHOULD BE AS INDICATED. THE
SUMP OF THE BATH IS SUPPORTED BY INTEGRAL FEET AND NO ADDITIONAL SUMP SUPPORT IS REQUIRED. ONCE THE BATH IS IN
PLACE, THE FEET SHOULD BE SHIMMED ACCORDINGLY, SO THAT THE RIM OF THE BATH CONTACTS THE STRINGER OR PIER BUT
SUPPORTS NO WEIGHT. ANY FINISH MATERIAL, SUCH AS TILE OR WALL BOARD, MUST BE SELF-SUPPORTING IF IT CONTACTS THE
RIM OF THE BATH.
SUGGESTED INSTALLATION
METHOD
LEVELING SURFACE
WATERPROOF
SEALANT
BATH
TYPICAL INSTALLATION
AS DESIRED
(464mm)
*SEE CUTOUT TEMPLATE PROVIDED
UNLESS AN ACCESS OPENING OF AT LEAST
12" X 24" (305 X 610 mm) IS PROVIDED,
WARRANTY SERVICE WILL NOT BE PERFORMED.
18-1/4
*36-1/2
(927 mm)
CUTOUT
AS DESIRED
ACCESS PANEL
*67
(1702 mm)
CUTOUT
24
(610mm)
12
(305 mm)
751753-100 Rev. J (2)
SPIC AND SPAN® IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE
Loading...