American Standard 2705.118W, 2705.218W, 2703.118W, 2703.218W User Manual

ELLISSE BUILT-IN™ WHIRLPOOL

HIGH GLOSS ACRYLIC

ELLISSE BUILT-IN WHIRLPOOL Whirlpool Featuring System I:

❏ 2703.118W End Mount Pump, Right Hand Outlet ❏ 2703.218W End Mount Pump, Left Hand Outlet ❏ 2705.118W Front Mount Pump, Right Hand Outlet ❏ 2705.218W Front Mount Pump, Left Hand Outlet

• Acrylic with fiberglass reinforcement

• Pre-leveled tub bottom

• Dual, molded-in arm rests

• Integral 3-sided tiling/water retention flange

• 1.5 HP single speed, self-draining pump/motor

• Factory installed power cord and plug

• Six multi-directional and flow-adjustable jets

including:

- Two foot jets

- Two body massage jets

- Two back-rest jets

• Deck-mounted air switch On/Off

• Two silent air volume controls

• Quick Connect Safe-T-Heater connection

system

• Factory installed and tested whirlpool system

StayClean™ Whirlpool Featuring System I:

❏ 2703.118WC End Mount Pump, Right Hand outlet ❏ 2703.218WC End Mount Pump, Left Hand outlet ❏ 2705.118WC Front Mount Pump, Right Hand outlet ❏ 2705.218WC Front Mount Pump, Left Hand outlet

• Same as above except with the StayClean™ whirlpool system featuring Antimicrobial AlphaSan®

Nominal Dimensions: 1524 x 813 x 546mm (60” x 32” x 21-1/2")

BV-17

NOTE: Roughing-in dimensions and product

specifications shown on reverse side of page.

Rev. 3/03

Compliance Certifications Meets or Exceeds the Following Specifications:

• Underwriters Laboratories - Hydromassage Bathtubs UL 1795

• ASME A112.19.7M for Whirlpool Appliances

• ANSI Z124.1 for Plastic Bathtubs

• ASTM E162 for Flammability

• NFPA 258 for Smoke Density

To Be Specified - Required:

❏ Color: ❏ Bath Filler: (specify finish) ❏ Bath Drain: 1583.470 (specify finish) ❏ Grab Bar Kit: 9827-200-two per kit (specify finish)

To Be Specified - Optional:

❏ Safe-T-Heater*: 9075.120 ❏ Ellisse Apron: 9160.2705(specify color) ❏ Jet Trim Ring Kit: 9860.200-two per kit (specify

finish)

For color/finish availability and other faucet choices, please see the Product Selector and Pricing Guide.

* NOTE: the Safe-T-Heater is designed to maintain water temperature during operation. It will not heat cold water to desired bathing temperature.

ELLISSE BUILT-IN™ WHIRLPOOL

HIGH GLOSS ACRYLIC

SEE FITTING

NOTES:

BATH MUST BE INSTALLED ABOVE THE FLOOR LINE AS BUILT-IN INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.

REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION. OPTIONAL APRON NO. 9160.2705 & GRAB BAR KIT NO.9827.200 AVAILABLE AND MUST BE ORDERED SEPARATELY. FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. LEFT HAND OUTLET SHOWN, RIGHT HAND REVERSE DIMENSIONS 2703.118W/2705.118W. PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS. IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY

HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING

SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER. ON SYSTEM II: CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL, A MINIMUM OF 152mm (6) ABOVE ROUGH

FLOOR.

IMPORTANT:

Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1.These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

SPECS FOR

DIMENSION

387mm

(15-1/4)

813mm

(32)

C/L OF

SUPPLIES

19mm (3/4)

229mm (9)

229x305mm (9x12) FLOOR CUTOUT

1524mm

(60)

FINISHED WALL LINE

WATER RETENTION FLANGE (3) SIDES

PUMP

305mm

(12) OPT.

TOP

DECK

546mm

(21-1/2)

95mm (3-3/4)

102mm (4)

51mm (2)

ROUGH FLOOR

51mm (2)

C/L OF DRAIN OUTLET

C/L OF

SHOWER ARM

SAFE-T-HEATER

REMOVABLE BLANK

C/L OF

OVERFLOW

INTEGRAL FEET

1-1/2 N.P.T.

THREADS

1-1/2 O.D.

TAILPIECE

ALT. PUMP

LOCATION

C/L OF VALVES

C/L OF SPOUT

38mm

(1-1/2)

GENERAL SPECIFICATIONS FOR 2703/5 WHIRLPOOL

INSTALLED SIZE WEIGHT WEIGHT w/WATER GAL. TO OVERFLOW WHIRLPOOL MIN. OPERATING VOL. BATHING WELL AT SUMP BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING (PROJECTED AREA) PTS. CUBE (FT3)

SYSTEM I PUMP SYSTEM II PUMP

WHIRLPOOL ELECTRICAL SPECIFICATIONS

60 x 32 x 21-1/2 In. (1524 x 813 x 546mm)

44-1/2 X 20 In. (1130 mm X 508 mm) 58 X 26-1/4 In. (1473 mm X 667 mm)

48 Lbs./Sq.Ft. (231 Kgs./Sq.m)

ON/OFF SWITCH

PROVIDE ACCESS

TO PUMP FOR SERVICING

ON ALL INSTALLATIONS

FINISHED WALL

WATER RETENTION FLANGE

■

LEVELING STRINGER NOT FOR SUPPORT

ROUGH FLOOR

1.6 HP, 9.7 AMPS, 120V.

2.1 HP, 15.6 AMPS, 120V.

533mm

(21)

83mm (3-1/4)

141 Lbs. (63 Kg.)

643 Lbs. (292 Kg.)

60 Gal. (277 L) 50 Gal. (189 L)

14-1/2 In. (368 mm)

38mm (1-1/2)

20.8

35.3

1651-1981mm

(65-78)

OPTIONAL

UNDERSIDE OF DECK

+ 2 hidden pages