American Standard 2703.XXXW, 2705.XXXW User Manual
ELLISSE BUILT-IN™
2703.XXXW
2705.XXXW
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
SEE FITTING
305mm
(12) OPT.
TOP
OF
DECK
546mm
(21-1/2)
SPECS FOR
DIMENSION
(15-1/4)
813mm
(32)
SUPPLIES
95mm
(3-3/4)
387mm
C/L OF
102mm
(4)
ROUGH
FLOOR
19mm
(3/4)
C/L OF DRAIN
OUTLET
C/L OF
SHOWER ARM
SAFE-T-HEATER
REMOVABLE BLANK
51mm
(2)
C/L OF
OVERFLOW
INTEGRAL
FEET
1-1/2 N.P.T.
THREADS
1-1/2 O.D.
TAILPIECE
51mm
(2)
GENERAL SPECIFICATIONS FOR 2703/5 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
SYSTEM I PUMP
SYSTEM II PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SERIES WHIRLPOOL
INSTALLATION INSTRUCTIONS
1524mm
229mm
(9)
229x305mm
(9x12) FLOOR
CUTOUT
ALT. PUMP
LOCATION
60 x 32 x 21-1/2 In. (1524 x 813 x 546mm)
(60)
WATER RETENTION
FINISHED
WALL LINE
C/L OF
VALVES
C/L OF
SPOUT
38mm
(1-1/2)
44-1/2 X 20 In. (1130 mm X 508 mm)
58 X 26-1/4 In. (1473 mm X 667 mm)
FLANGE (3) SIDES
ON/OFF SWITCH
TO PUMP FOR SERVICING
ON ALL INSTALLATIONS
FINISHED WALL
WATER
RETENTION
FLANGE
■
LEVELING
STRINGER
NOT FOR
SUPPORT
ROUGH
FLOOR
48 Lbs./Sq.Ft. (231 Kgs./Sq.m)
533mm
83mm
(3-1/4)
14-1/2 In. (368 mm)
1.6 HP, 9.7 AMPS, 120V.
2.1 HP, 15.6 AMPS, 120V.
PUMP
PROVIDE ACCESS
1651-1981mm
(65-78)
OPTIONAL
38mm
(1-1/2)
UNDERSIDE
OF DECK
(21)
141 Lbs. (63 Kg.)
643 Lbs. (292 Kg.)
60 Gal. (277 L)
50 Gal. (189 L)
20.8
35.3
THANK YOU...
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
List of Optional Components (not included):
• Apron Kit*
• Safe-T-Heater 9075.120*
* see your American Standard Distributor
List of Required Components (not included):
• Drain 1583.470* • Bath Filler*
* see your American Standard Distributor
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any
shipping damage. If such damage is found, report it to
your vendor immediately.
After inspection and during installation, protect the bath
from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit
and check for leaks.
If a whirlpool, do not make modifications to the whirlpool
system or remove pump from factory mounting. This
could adversely affect the safety and performance of the
whirlpool and void the warranty. Do not handle or move
the whirlpool by the pump, motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided
with the bath and must be ordered separately. Framing
and enclosing materials are provided by others. Check
for availability of optional American Standard wall tiling
bead (required for recess installations).
Protect all finished surfaces of the whirlpool during
construction and installation using a drop cloth.
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 15 or 20 amp GFCI
Outlet
• Cement, Plaster,
Grout
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
752352-100 REV. H
WARNING! Do not lift whirlpool by the piping harness at any time.
© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
FRAMING AND INSTALLATION
BATH MAY ONLY BE INSTALLED ABOVE THE FLOOR LINE IN A RECESS TYPE INSTALLATION, AS SHOWN IN RECESS
INSTALLATION DIAGRAM.
THE FOLLOWING PROCEDURE MUST BE USED FOR ALL INSTALLATIONS: STRINGER OR PIER HEIGHT SHOULD BE AS
INDICATED. THE SUMP OF THE BATH IS SUPPORTED BY INTEGRAL FEET AND NO ADDITIONAL SUMP SUPPORT IS
REQUIRED. ONCE THE BATH IS IN PLACE, THE FEET SHOULD BE SHIMMED ACCORDINGLY, SO THAT THE RIM OF THE BATH
CONTACTS THE STRINGER OR PIER BUT SUPPORTS NO WEIGHT. ANY FINISH MATERIAL, SUCH AS TILE OR WALL BOARD,
MUST BE SELF-SUPPORTING IF IT CONTACTS THE RIM OF THE BATH.
LOCATE STUDS AS REQUIRED. INSURE ROUGH DIMENSIONS ARE PROPER, PLUMB AND SQUARE. FOR REAR MOTOR
MOUNT WHIRLPOOLS, PROVISION MUST BE MADE IN ALL INSTALLATIONS FOR AN ACCESS OPENING FOR SERVICING
PUMP AND CONTROLS.
TYPICAL RECESS INSTALLATION STUD FLANGE BRACKET
INSTALLATION
BATH
FLANGE
BATH
DRYWALL
SCREW
STUD
FLANGE
BRACKET
STUD
2 X 4
STRINGER
SUPPORT
533mm
(21)
WALL
BOARD
ADHESIVE
1527mm
TILE
SEALANT
(60-1/8)
775mm
(30)
813mm
TUB WIDTH
1 X 3 X 8
LEVELING
STRINGER
1 X 3 LEVELING
STRINGER
305mm
(12)
(32)
610mm
(24)
BATH
LEVELING
STRINGER
WHIRLPOOL ONLY:
UNLESS AN ACCESS OPENING OF AT LEAST
305mm X 610mm(12" X 24") IS PROVIDED,
WARRANTY SERVICE WILL NOT BE PERFORMED.
SECURE THE BATH TO THE STUDS
AS SHOWN USING THE SCREWS
AND BRACKETS PROVIDED SEE STUD FLANGE BRACKET
INSTALLATION
STUD FLANGE BRACKET INSTALLATION
PROVIDED WITH THE BATH IS A PACKAGE OF (4) FOUR STUD FLANGE BRACKETS AND (8) EIGHT SCREWS. INSTALL BRACKETS AND
SCREWS AS SHOWN IN WALL BRACKET INSTALLATION DETAIL. TWO BRACKETS SHOULD BE LOCATED EVENLY ACROSS THE BACK TILE
FLANGE AND INSTALL ONE BRACKET ON EACH END OF THE BATH, TOWARDS THE FRONT END OF THE TILE FLANGE. THIS WILL ALLOW
TILE FLANGE TO BE HELD SECURELY AGAINST STUDWALL OF RECESS INSTALLATION.
752352-100 REV. H (2)
SPIC AND SPAN® IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE
Loading...