American Standard 2696.102, 2696.202 User Manual
™
INSTALLATION INSTRUCTIONS
5-1/2' Cast Iron Bath
Model 2696.102
Model 2696.202
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read
these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
CAUTION: RISK OF PERSONAL INJURY. CAST IRON BATHS ARE EXTREMELY HEAVY.
!
THIS IS A TWO PERSON INSTALLATION.
Recommended Tools & Materials
• Plumbers Putty
• Silicone Sealant
• Metal Shims
• Wall Coverings, As Needed
1
• Rule
• Level
• Square
• Pliers
• Pipe Wrench
• Wood Working Tools
REMOVE THE OLD BATH (IF APPLICABLE)
Disconnect the drain at the trap. Remove any
old wall material. Slip boards under the old
bath feet to protect the floor, and slide the
old bath out of the recess as illustrated.
Fig. 1
Old Bath
Floor Protective
Material
PREPARE SUBFLOOR
Check the flooring under the bath area, and repair it if necessary. Make sure the subfloor is level.
FINISHED
WALL
FINISHED
WALL
STD. 1-1/2
DRAIN OUTLET
73mm
2-7/8"
DIA.
76mm
3"
406mm
ROUGH
FLOOR
16"
229 x 305mm
9" X 12" HOLE
IN SUB FLOOR
FOR BELOW
FLOOR ROUGH
Fig. 2
18mm
11/16"
64mm
2-1/2"
SUPPORT
FEET
LEFT HAND TUB ILLUSTRATED
RIGHT HAND TUB IS REVERSED
DETERMINE FRAMING ROUGH-IN
Construct a recess using 2 x 4 construction designed for your particular installation.
Allow for thickness of finished wall material.
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2007
32mm
1-1/4"
194mm
7-5/8"
-1-
FINISHED
WALL
1682mm
66-1/4"
FINISHED
WALL
102mm
4"
384mm
15-1/8"
813mm
32"
FINISHED
WALL
740170-100 Rev. B
A
ME
R
IC
A
N
S
TA
N
D
A
R
D
AMER
I
C
AN
ST
A
N
D
AR
D
DRAIN
2
Install the overflow and drain assembly onto the
COMPLETE FINISH WALL
4
tub per manufacturer's instructions.
!
CAUTION: Risk of personal injury and product damage.
Protect the bath surface. Cover the framing and walls with wallboard.
Apply a bead of silicone sealant where the wallboard meets the
bath. Install the wall covering so it is 1/16" above the enameled
surface. Install the finish wall material to the subwall. Use silicone
sealant to seal the joints between the bath rim and the finish wall.
Install the finish floor. Apply silicone sealant along the edge of the
Fig. 3
bath apron.
Finish Wall Material
INSTALLATION
3
Position bathtub within the recess, check level, front to back, side
to side. Also check drain clearance hole in sub floor. Use metal
shims under support feet. Insert the drain tailpiece into the trap.
UNDERLAYMENT
FINISHED TILE FLOOR
Silicone
Sealant
Bath Cross
Section
Wallboard
Silicone Sealant
2x4 Studding
Fig. 6
Fig. 4
INSTALL PLUMBING
!
CAUTION: Risk of damage to bath bottom and subfloor.
Ensure a watertight seal on all drain connections. When the bath is
securely positioned, connect the drain to the trap. An access panel
will simplify future maintenance.
Fig. 5
SUB FLOOR
IMPORTANT CONSUMER INFORMATION
5
HOUSEKEEPING RESPONSIBILITIES
The slip-resistant surface on this bathtub meets or exceeds
the requirements of ASTM-F-462 for slip resistance.
DANGER: Improper maintenance or cleaners may permanently
!
remove the slip-resistant surface on American Standard bathtubs.
NOTE:
DO NOT use steel wool, wire brushes, metal scrapers or abrasive
sponge pads to clean a American Standard Bathtub.
DO NOT use buffing machines on the slip-resistant surface.
DO NOT use high alkaline or strong acid cleaners.
DO NOT use abrasive cleaners.
Use only non-abrasive cleaners and a soft nylon brush to clean
Connect Here
the slip-resistant surface. When using commercial cleaners, use
cleaners with a pH of between three and eight.
Follow cleaner manufacturer instructions very carefully.
If inspection of this American Standard plumbing product, within one year after its initial installation, confirms that it is defective in materials or workmanship, American Standard will repair or,
at its option, exchange the product for a similar model.
This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing
contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was
not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American Standard.
American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American Standard be
responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly
excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such
statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a
description of the product model and of the defect) be sent to the following address:
AMERICAN STANDARD ONE-YEAR LIMITED WARRANTY
In the United States:
American Standard Inc.,
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
www.americanstandard-us.com
740170-100 Rev. B
In Canada:
American-Standard,
2480 Stanfield Rd.,
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: (800) 387-0369
www.americanstandard.ca
-2-
In Mexico:
Customer Service Manager
Ideal Standard, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com.mx
Loading...