American Standard 2675 User Manual
COLONY™ 5'
2675 SERIES
HIGH GLOSS ACRYLIC
WHIRLPOOL/BATHING POOL
SHOWN LESS ALL FITTINGS
PROVIDE ACCESS TO PUMP FOR
SERVICING ON ALL INSTALLATIONS
1524 mm
(60)
305 mm
(12)
102 mm
1-1/2 N.P.T.M.
THREADS
(1) AIR VALVE
(4)
216 mm
(8-1/2)
FINISHED
SEE FITTING
SPECS FOR
DIMENSIONS
WALL
832 mm
(32-3/4)
416 mm
(16-3/8)
C/L OF
SUPPLIES
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
(65 & 78)
19 mm
(3/4)
305 mm
(12)
38 mm
(1-1/2)
C/L OF
OVERFLOW
79 mm
(3-1/8)
502 mm
(19-3/4)
ROUGH
FLOOR
BATH
SUPPORT
MATERIAL
229 mm
(9)
CUTOUT IN FLOOR FOR DRAIN
(6) JETS
38 mm
(1-1/2)
1-1/2 O.D.TAILPIECE
GENERAL SPECIFICATIONS FOR 2675 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
60 x 32-3/4 x 19-3/4 In.(1524 x832 x 502mm)
27-1/2 x 56 In.(699 x 1422mm)
44 Lbs./Sq. Ft. (213 Kgs/Sq. m.)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
NOTE: Deck-mounted fittings are not recommended.
INSTALLATION INSTRUCTIONS
OUTLINE OF CUTOUT
1486 mm x 794 mm
(58-1/2 X 31-1/4 )
PUMP
C/L OF
SHOWER ARM
C/L OF
VALVES
■ LEVELING STRINGER
NOT FOR SUPPORT
70 mm
(2-3/4)
95 Lbs. (43 Kg.)
604 Lbs. (275 Kg.)
61 Gal. (230 L.)
20 x 39 In. (508 x 991mm)
1.1 HP, 9.9 AMPS, 120V.PUMP
42 Gal. (159 L.)
14-1/4 In. (362mm)
C/L OF
SPOUT
117 mm
(4-5/8)
464 mm
(18-1/4)
15.6
29.6
ON/OFF
SWITCH
THANK YOU...
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
List of Optional Components (not included):
• Tile Bead Kit 751755-100*
• Apron Kit*
List of Required Components (not included):
• Drain 1583.470* • Bath Filler*
* see your American Standard Distributor
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
GENERAL INSTALLATION INFORMATION
Carefully uncrate, peel-out protective film and
inspect your new bath for any shipping damage. If
such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath
from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit
and check for leaks.
If a whirlpool, do not make modifications to the whirlpool
system or remove pump from factory mounting. This
could adversely affect the safety and performance of the
whirlpool and void the warranty. Do not handle or move
the whirlpool by the pump, motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided
with the bath and must be ordered separately. Framing
and enclosing materials are provided by others. Check
for availability of optional American Standard wall tiling
bead (required for recess installations).
Protect all finished surfaces of the whirlpool during
construction and installation using a drop cloth.
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 2 x 3 or 2 x 4
Stringers
• Drop Cloth
• 15 amp GFI
Outlet
• Cement, Plaster,
Grout
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
752445-100 Rev. E
WARNING! Do not lift whirlpool by the piping harness at any time.
© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
INSTALLATION AND FRAMING INSTRUCTIONS
The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs
as required. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an
access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for
access to the drain components.
NOTE: The apron should not be used as the primary access opening.
1. As shown in Fig. 1, mark the position of the underside of the deck by tracing a line onto the studs at the height indicated,
using a level or other suitable straight edge.
2. With the top of the 2 x 4 stringer touching the traced line, attach the stringer to the studs.
3. Install drain components to the whirlpool following the manufacturers instructions. Before replacing your whirlpool for final
installation, be certain that an opening has been provided in the sub-floor for the drain. See the roughing-in drawing for
suggested opening size and location dimensions.
4. This bath must be supported along its entire bottom in all types of installations. We recommend the use of mortar or
plaster as bedding material (sand is not recommended). Apply enough bedding to support the complete bottom of the
bath. After the bedding has been poured, and before it sets, lower the bath into place until the rim is leveled against the
leveling stringers (see "Typical Installation Methods"). The rim of the bath MUST NOT support weight. Allow the bedding
material to completey harden before applying weight to the rim or bottom of the bath. Any finish material such as tile or
wall board must be self-supporting if it contacts the deck of the bath.
FIG. 1
464mm
(18-1/4)
TYPICAL RECESS INSTALLATION
TILE
WALLBOARD
TILE
BEAD
STRIP
SEALANT
BATH
ADHESIVE
LEVELING
STRINGER
NOTE: Tile bead kit not included and must be
purchased separately.
TYPICAL PIER TYPE INSTALLATION
AS DESIRED
794mm
464mm
(18-1/4)
(31-1/4)
CUTOUT
1486mm
(58-1/2)
CUTOUT
464mm
(18-1/4)
1527mm
(60-1/8)
UNLESS AN ACCESS OPENING OF AT LEAST
12" X 24" (305 X 610MM) IS PROVIDED,
WARRANTY SERVICE WILL NOT BE PERFORMED.
819mm
(32-1/4)
832mm
(32-3/4)
TUB WIDTH
LEVELING
STRINGERS
WHIRLPOOL ONLY:
610mm
(24)
305mm
(12)
752445-100 Rev. E (2)
LEVELING
SURFACE
WARRANTY SERVICE WILL NOT BE PERFORMED.
AS DESIRED
WATERPROOF
SEALANT
BATH
UNLESS AN ACCESS OPENING OF AT LEAST
12" X 24" (305 X 610MM) IS PROVIDED,
WHIRLPOOL ONLY:
ACCESS PANEL
610mm
(24)
305mm
(12)
Loading...