American Standard 2664.202, 2664.102 User Manual
SCALA CORNER™
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
SCALA CORNER WHIRLPOOL & BATHING
POOL
❏ 2664.118 Whirlpool with right hand drain outlet
❏ 2664.218 Whirlpool with left hand drain outlet
• Acrylic with fiberglass reinforcement
• Factory installed and tested whirlpool
system
• 1.0 HP single speed self-draining pump/motor
with dry run seal
• Six multi-directional and individually flow-rate
adjustable color-coordinated jets
• Two color-coordinated air volume controls
• Anti-vortex suction fitting
• Deck-mounted color-coordinated air switch
On/Off control
• U.L.
®
Listed Hydromassage bathtub
• Textured tub bottom pattern
• Integral sump support feet
• Factory installed power cord with plug
• Dual molded-in lumbar support
• Molded-in seat
• Molded-in water retention flange
❏ 2664.102 Bathing Pool only with Right-hand
Drain Outlet
❏ 2664.202 Bathing Pool only with Left-hand
Drain Outlet
Nominal Dimensions: 1524 x 1524 x 502mm
(60” x 60” x 19-3/4")
© 2002 American Standard Inc.
BV-029
SPS 2664
To Be Specified - Required:
❏ Bath Filler*
❏ Drain: 1553.270 (specify Chrome , Polished Brass
or Satin)
❏ Color:
To Be Specified - Optional:
❏ Metal Air Volume Control Kit: 9850.200-two
per kit (specify Chrome, Polished Brass or Satin)
❏ Metal Jet Trim Ring Kit: 9860.200-two
per kit (specify Chrome or Polished Brass or Satin)
* See faucet section for models available
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
Revised 3/98
Compliance Certifications Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
SCALA CORNER™
WHIRLPOOL & BATHING POOL
HIGH GLOSS ACRYLIC
© 2002 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE
INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED.
ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
CONCEALED PIPING NOT INCLUDED.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY
HOLES: CHECK FOR INTERFERENCE
WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES
DRILLED BY INSTALLER.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI
Standard Z124.1. These measurements are subject to change or cancellation. No responsibility is assumed for use of
superseded or voided pages.
●
■
(5-1/2)
m
140m
1632mm
1600mm
(64-1/4)
1080mm
(63-1/2)
(42-1/2)
m
1524m
(60) TYP.
m (59-1/4) TYP.
1505m
O
C
E
R
●
64 X
M
M
279m
N
E
F
D
E
D
(2-1/2 X
m
724m
IN
T
IT
11)
(28-1/2)
m
TIO
A
C
LO
G
N
254mm X 254mm
(10 X 10) DRAIN
OUTLET CUTOUT
1356m
(53-3/8)
m
25mm (1)
INTEGRAL TILE
FLANGE (2) SIDES
1524mm
(60) TYP.
(42-1/2)
1080mm
(63-1/2)
1600mm
140mm (5-1/2)
(64-1/4)
1632mm
1505mm (59-1/4) TYP.
724mm (28-1/2)
RECOMMENDED FITTING LOCATION
●
64 X 279mm (2-1/2 X 11)
254mm X 254mm
(10 X 10) DRAIN
OUTLET CUTOUT
5
3
1
(5
m
)
m
6
/8
-3
3
25mm (1)
INTEGRAL TILE
FLANGE (2) SIDES
552mm
(21-3/4)
216mm
(8-1/2)
19mm(3/4)
CUTOUT DIMENSION
C
OF DRAIN OUTLET
L
13mm (1/2) INTEGRAL
TILE FLANGE
LEVELING
STRINGER
(NOT FOR
SUPPORT)
38mm
(1-1/2)
124mm
4-7/8
60mm
(2-3/8)
GENERAL SPECIFICATIONS FOR 2664 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
SYSTEM I PUMP
WHIRLPOOL ELECTRICAL SPECIFICATIONS
60 x 60 x 19-3/4 In. (1524 x 1524 x 502mm)
ON/OFF
406mm
SWITCH
(16)
1041mm
(41)
95mm
(3-3/4)
1-1/2" N.P.T.M. THREADS
1-1/2" O.D. TAILPIECE
42 x 28 In. (1067 x 711mm)
60 x 40 In. (1524 x 1016mm)
37 Lbs./Sq.Ft. (182 Kgs./Sq.m)
PROVIDE ACCESS
FOR SERVICING
PUMP & CONTROLS
INTEGRAL
FEET
SUPPORT
114 Lbs. ( 51 Kg.)
781 Lbs. (351 Kg.)
80 Gal. (303 L)
58 Gal. (220 L)
14 In. (356mm)
1.0 HP, 9.9 AMPS,120V.
m
775m
(30-1/2)
ROUGH
FLOOR
464mm
18-1/4
41.7
68.4
502mm
(19-3/4)
552mm
(21-3/4)
216mm
(8-1/2)
19mm(3/4)
CUTOUT DIMENSION
C
OF DRAIN OUTLET
L
13mm (1/2) INTEGRAL
TILE FLANGE
LEVELING
STRINGER
(NOT FOR
SUPPORT)
38mm
(1-1/2)
124mm
4-7/8
GENERAL SPECIFICATIONS FOR 2664 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT3)
m
m
5
7
-1
7
0
406mm
(16)
1041mm
(41)
95mm
(3-3/4)
1-1/2" N.P.T.M. THREADS
60mm
1-1/2" O.D. TAILPIECE
(2-3/8)
60 x 60 x 19-3/4 In. (1524 x 1524 x 502mm)
42 x 28 In. (1067 x 711mm)
60 x 40 In. (1524 x 1016mm)
36 Lbs./Sq.Ft. (177 Kgs./Sq.m)
(3
ROUGH
FLOOR
INTEGRAL
FEET
SUPPORT
94 Lbs. (42 Kg.)
761 Lbs. (342 Kg.)
80 Gal. (303 L)
14 In. (356mm)
)
/2
464mm
18-1/4
41.7
68.4
502mm
(19-3/4)
Loading...