American Standard 2633.1, 2257.001, 3353, 2634.001, 3351 User Manual
...
INSTALLATION INSTRUCTIONS
AFWALL FLUSH VALVE
WALL-MOUNTED TOILETS
Model 3351, 3352, 3353, 3354, 2257.001, 2633.100, 2634.001
Meets the American Disabilities Act Guidelines and ANSI A117.1
Requirements for the Physically Challenged
Thank you for selecting American Standard – the benchmark of fine quality for
over 100 years. To ensure thisproduct is installed properly, please read these
instructions carefully before you begin. (Certain installations may require
professional help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR
HANDLING TO AVOID BREAKAGE AND POSSIBLE INJURY!
NOTE: For proper operation product requires a minimum of 30 psi working line pressure
RECOMMENDED TOOLS AND MATERIALS
Closet Carrier Support
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Carpenters Level
Flush Valve
1
Pictures may not exactly define contour of china
1" N.P.T. OR C.W.T. SUPPLY
AS REQUIRED TO FLUSH VALVE
C/L
121mm
(4-3/4")
356mm
1-1/2" SPUD
381mm
(15
")
or
432mm
(17
")
381mm
(15
432mm
(17
(14")
229mm
(9)
C/L OF
OUTLET
1" C.W.T. OR N.P.T. SUPPLY
AS REQ'D NOT FURNISHED
121mm
(4-3/4")
41mm
(1-5/8")
89mm
(3-1/2")
(4) 22mm (7/8")
DIA. HOLES
")
or
")
(4) 22mm
(7/8")
HOLES
254mm
(10")
38mm
(1-1/2")
VACUUM BREAKER
356mm
C/L OF
OUTLET
292mm
(11-1/2")
191mm
(7-1/2")
133mm
(5-1/4")
C/L
(14")
229mm
(9")
When installed,
top of seat is
17" to 19"
(432mm to 483mm)
from the finished
floor.
184mm
or
(7-1/4
")
298mm
(11-3/4")
191mm
(7-1/2")
133mm
184mm
or
(5-1/4")
(7-1/4")
(3-1/4")
62mm
(2-1/8")
142mm
(5-1/4")
19mm
(3/4")
83mm
FINISHED WALL
660mm
(26")
73mm
(2-7/8")
32mm
(1-1/4")
FOR WALLS UP TO 1" IN THICKNESS FOR EACH INCH
ADDITIONAL THICKNESS OF WALL ADD 25mm (1) TO
MEASUREMENT SHOWN
95mm
(3-3/4
(3/4")
19mm
83mm
(3-1/4")
62mm
(2-1/8")
(5-1/4")
133mm
470mm
(18-1/2")
C/L OF SEAT POST
HOLES 140 mm
(5-1/2") CENTER
330mm
(13")
FINISHED
FLOOR
FINISHED WALL
")
660mm
")
(26
38mm (1-1/2") DIA. HOLE IN WALL
76mm(3") DIA. HOLE IN WALL
FOR 1-1/2" SPUD
32mm
(1-1/4")
470mm
(18-1/2")
C/L OF SEAT POST HOLES
140mm(5-1/2") CENTERS
330mm
(13")
FINISHED
FLOOR
Refer to instructions supplied with wall carrier for proper installation of 4-bolt support
system wall cavity requirements and rough-in information for waste outlet piping.
2
FIXTURE MOUNTING
Fixture studs should project
1-7/8" (48mm) from face of
finished wall.
Side View
Front View
FINISHED
WALL
1-7/8"
(48mm)
(4) STUDS
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2010
7301115-100 Rev. C
3
CLOSET
CARRIER
SYSTEM
5
Place back-up nuts on both bottom bolts, and
the top left-hand bolt only.
Adjust the two lower back-up nuts so that front
face of nuts is flush with finished wall.
Adjust waste horn to project 5/16" (7mm) from
finished wall.
FINISHED WALL
(3) NUTS
WASTE
HORN
5/16" (7mm)
4
Using a level, adjust the top left back-up nut so that
it is in the same vertical plane as the lower left back-up
nut. (If wall surface is irregular, the three back-up
nuts must be positioned to allow a minimum 1/16"
gap between fixture and wall surface.)
FINISHED WALL
1/16" (2mm)
(IRREGULAR
WALL SURFACE)
LEVEL
NOTE: Bearing nuts and washers must be set to take full loading from the fixture allowing
1/16" (2mm) clearance between fixture and wall.
Follow support manufacturer's recommended setting of closet outlet connection.
Place felt or neoprene gasket (wax ring not recommended) on closet outlet.
When the fixture is installed, closet outlet gasket must be compressed sufficiently to
assure a gas and watertight seal.
The following steps require a helper:
Install bowl on support using cap nuts and fiber washers with the back-up nuts and washers.
DO NOT APPLY TOP RIGHT FIBER WASHER AND CAP NUT UNTIL OTHER CAP NUTS
HAVE BEEN FIRMLY TIGHTENED USING A WRENCH.
Install top right cap nut with fiber washer and run up hand tight. Wrench tighten approximately
1/4 turn.
Apply sealant to gap between bowl and finished wall. Remove excess sealant.
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
www.americanstandard.com
7301115-100 Rev. C
In Canada:
AS Canada ULC
5900 Avebury Ave.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: (800) 387-0369
www.americanstandard.ca
- 2 -
In Mexico:
Customer Service Manager
AS Maquila, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com.mx
Loading...