American Standard 2580 User Manual
Installation
Instructions
THE
COLLECTION
by
™
BIDET FITTING
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years.
2580
To ensure that your installation proceeds
smoothly--please read these instructions carefully before you begin.
Required Tools
Flat Blade Screwdriver
Tubing Cutter
Phillips Screwdriver
Adjustable Wrench
*Wrench
*Supplied with Fitting
MOUNTING BIDET FAUCET
1
CAUTION
Place MOUNTING NUTS (1) onto the VALVE BODIES
(2) and insert VALVE BODIES (2) through outside
holes, from underside of the BIDET LEDGE. Drop the
RUBBER RING (3) over the VALVE BODIES (2) and
thread DECK ADAPTER (4) onto VALVE BODIE (2)
until it locks against the internal stop.
Tighten the MOUNTING NUT (1) to secure the
VALVE BODY (2).
Remove ESCUTCHEON (5), WASHER (10) and
UPPER GASKET (7) from TRANSFER VALVE (8) and
insert into the center forward hole of BIDET.
Replace UPPER GASKET (7), and ESCUTCHEON (5)
until it locks against the internal stop. Position the
side threaded outlet rearward and secure
MOUNTING NUT (9).
Turn off hot and cold water
supplies before beginning.
Channel Locks
Roughing-in Dimensions
BIDET OUTLINE
IS SYMBOLIC
1-3/16
DRAIN INSTALLATION
2
DOUCHE
SPRAY
3-7/8
DIA.
1-3/8
MAX.
FINISHED
FLOOR
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
TRANSFER VALVE
(FOR FLUSHING
RIM OR SPRAY)
7/8 DIA.
ADJ. 1-1/4
TO 2-1/4
1-3/8
DIA.
5-1/2
8 TO 12
(C)
FINISHED
WALL
2-1/8
DIA.
1-1/4 O.D. TAILPIECE
(H)
2-1/4
DIA.
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
M968292
STOPPER
4
3
BIDET
LEDGE
Assemble O-RING (1), WASHER (2), PIVOT
5
10
2
HOT
1
8
COLD
7
ROD (3) and NUT (4) to DRAIN BODY (5).
Concave side of cup WASHER (2) is toward
ball.
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY (5).
Apply a bead of PUTTY to underside
of FLANGE (9).
Feed DRAIN BODY (5) up through BIDET
and thread FLANGE (9) fully onto
BODY (5).
Tighten LOCKNUT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back
of the BIDET.
Push DRAIN ESCUTCHEON (10) onto
TAILPIECE (11).
8
7
6
PUTTY
2
5
9
BIDET
4
1
11
CLIP
3
9
10
SPRAY INSTALLATION
3
Assemble SPRAY BODY (1) to BIDET. Apply putty to
underside of SPRAY BODY FLANGE (2) to seal and
secure with NUT (3).
Thread SPRAY HOSE (4) with SEAL WASHER (5) to
SPRAY BODY (1). Connect other end of HOSE (4) with
SEAL WASHER (6) to bottom outlet NIPPLE (7) of the
TRANSFER VALVE (8).
Thread SPRAY CAP (9) onto SPRAY BODY (1).
TEE AND HOSE CONNECTION
5
Insert SEAL (1) into ADAPTER (2) and tighten
ADAPTER (2) to side inlet of TRANSFER VALVE (3).
Install SEAL (4) into coupling nut of TEE (5)
and tighten connection to ADAPTER (2)
Connect HOSE COUPLING NUTS (6)
to Hot and Cold valve bodies
and securely tighten.
Cold
6
3
8
INSTALL HANDLES
6
LEVER HANDLES:
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without spline is facing up. See figure "A".
Thread HANDLE BASE (3) onto DECK ADAPTER (7)
Push HANDLE (4) onto ADAPTER (1).
Find correct position of HANDLE (4) by adjusting male teeth on
ADAPTER (1) to female teeth in HANDLE (4).
Secure HANDLE (4) with HANDLE SCREW (5).
2
PUTTY
7
6
9
1
3
5
4
4
Unscrew LIFT ROD NUT (1)
from LIFT ROD GUIDE (2).
Make sure SEAL (3) is seated
into ESCUTCHEON of LIFT ROD
GUIDE (2).
Drop LIFT ROD GUIDE (2) into
rear hole of bidet and from
below secure with LIFT ROD
NUT (1).
Hot
6
LIFT ROD GUIDE INSTALLATION
DIVERTER KNOB:
Install HANDLE ADAPTER (8) onto valve stem (12).
Push DIVERTER KNOB (7) onto HANDLE ADAPTER (8).
Install RING (9) onto DIVERTER KNOB 7) and tighten with
SCREW (10).
Press on KNOB CAP (11).
5
4
2
1
Front
2
3
1
Push INDEX CAP (6) in hole of HANDLE (4).
TOP
Figure "A"
SPLINE END DOWN
2
6
5
11
10
4
9
3
1
7
8
12
7
M968292
WATER SUPPLY CONNECTIONS
7
FINISH DRAIN INSTALLATION
8
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED AND HAVE
TO BE PURCHASED SEPARATELY
Connect water supplies to FAUCET (1) with 1/2" IPS
FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to proper length.
1
2
COUPLING NUT
3
Cold
FERRULE
Position BIDET fixture and secure to floor.
Insert lift rod into lift rod guide.
Position EXTENSION ROD (1) onto POP-UP ROD (2) and tighten
THUMBSCREW (3).
Remove one end of CLIP (4) from PIVOT ROD (7) by squeezing ends
together while sliding.
Insert PIVOT ROD (7) into second or third hole in EXTENSION ROD (1)
and reassemble CLIP (4). (EXTENSION ROD (1) may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION ROD (1) and
tightening THUMBSCREW (3).
Using metal TAILPIECE (5), make connection to the TRAP (6).
2
1
3
7
1
5
4
TEST INSTALLED FITTING
9
With HANDLES (1) in OFF
position, turn on WATER
SUPPLIES (2) and check all
connections for leaks.
Operate both handles to flush
water lines thoroughly. Turn
DIVERTOR (6) to rim wash and
bidet spray.
Operate Lift Rod (3) and fill
Bidet with water. Check that
DRAIN STOPPER (4) makes
a good seal and retains
water in Bidet. Adjust
stopper height by
repositioning Lift Rod (3) and
tightening Thumbscrew (5).
Release DRAIN STOPPER (4) and
check all drain connections for
leaks. Tighten if necessary.
6
1
6
3
2
4
5
10
11
SERVICE
To change direction of handle
rotation, proceed
as follows:
Turn valve to OFF position.
Remove HANDLE and
ADAPTER if present.
Remove SPRING CLIP (1).
Lift STOP WASHER (2),
turn 90° and replace.
Replace SPRING CLIP (1).
Replace HANDLE ASSEMBLY.
SPRAY (3) may accumulate dirt
causing distorted and reduced
water flow. Unscrew and remove
SPRAY (3) and rinse clean.
Replace SPRAY (3) and operate
handles several times from
OFF to ON position. Do not
force, handles turn only 90˚.
CARE INSTRUCTIONS:
2
90°
1
3
DO: SIMPLY RINSE THE PRODUCT CLEAN
WITH CLEAR WATER. DRY WITH A SOFT
COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT
2
WITH SOAPS, ACID, POLISH, ABRASIVES,
HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE
M968292
Loading...