American Standard 2555.900, 2555.901 User Manual
Installation
TOWNSQUARE
DECK-MOUNT BATH FILLER
with EverClean™ Finish
Instructions
2555.900
2555.901
Congratulations on purchasing your American
Standard faucet with EverClean finish found
only on American Standard faucets.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
IMPORTANT NOTICE TO INSTALLER!
Please check with local Code Authority for the installation requirements of this product. Some codes require an
additional temperature mixing valve to limit the maximum hot water temperature and vacuum breaker
(for products with hand spray) to be installed with this product.
Required Tools
Phillips Screwdriver
Adjustable Wrench
Flat Blade Screwdriver
ROUGHING-IN
DIMENSIONS
8-1/4
3-5/8
1-1/8 D.
4
Certified to comply with ANSI A112.18.1M
.3FW
ADJ. 6-1/2 TO 12
MOUNTING
SURFACE
1-1/4
MAX.
3
1-1/2 MAX.
1-3/16 D.
Channel Locks
SPOUT ASSEMBLY
1
Wrench
(Supplied)
CAUTION
Turn off hot and cold water supplies before beginning.
Insert SPOUT SHANK (1) through center hole of MOUNTING LEDGE.
Make sure that the RUBBER RING (2) is properly seated in RECESS
at base of SPOUT (3).
Assemble RUBBER WASHER (4) and BRASS WASHER (5) onto
SHANK (1). From underside of ledge secure SPOUT (3) into position
with LOCKNUT (6).
3
RECESS
4
6
1
2
5
MOUNTING
LEDGE.
3/4-14 MALE
N.P.T. INLETS
PREPARE TUBE AND TEE ASSEMBLY
2
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
4
3
NOTE
VALVE inlet is 3/4-inch NPT male connector.
(H)
1-1/16 D.
1
5
ADJ. 6-1/2 TO 12
3
4
(C)
12 MAX
2
VALVE ASSEMBLY
3
Install LOCKNUTS (1) and RUBBER WASHERS (3) onto valve shanks.
Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5)
into mounting holes from underside of ledge.
Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) is
properly seated on SHANK (7). Push COUPLING (9 or 9a) into TEE (6) and
attach to SPOUT SHANK (7) and tighten. Note: For product with Hand
Shower, COUPLING (9) is tightened using a 10mm (3/8”)
Hex Wrench.
Place RUBBER RING (11) into DECK ADAPTERS (10) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (5) position.
Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tighten
COUPLING NUT (14) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
10
11
5/16'' MIN.
5
MOUNTING SURFACE
3
1
11
FOR FITTING
LESS SPRAY
HOT
9a
DECK ADAPTER
10
10
11
5
8
13
14
4
7
13
MOUNTING
LEDGE
5
6
9
14
COLD
INSTALL HANDLES
4
Turn VALVE to OFF position.
Figure A: Install STEM ADAPTERS (7) onto VALVE STEMS (8).
Figure B: With colored side up, place FRICTION RING (6) over DECK ADAPTER (10). Loosely screw FRICTION NUT (5)
onto DECK ADAPTER (10). Do not tighten. Align flats on FRICTION NUT (5) with RIBS (9) in HANDLE BASE (4).
Figure C: Screw HANDLE BASE (4) with FRICTION NUT (5) onto DECK ADAPTER (10) until snug against mounting
surface and aligned properly.
Figure D: Install LEVER HANDLE (3) onto HANDLE ADAPTER (7) and align. Check alignment, if not satisfactory remove
and align. Insert HANDLE SCREW (2) and tighten. Press in INDEX BUTTON (1).
1
Figure B
2
3
4
9
4
5
Figure D
FLATS
Figure C
4
5
10
Figure A
5
6
7
8
10
6
10
ALIGNED
.3FW
Loading...