American Standard 2546004 Installation Manual
INSTALLATION INSTRUCTIONS
FREESTANDING TUB
HIGH GLOSS ACRYLIC SURFACE
Town Square® S Model 2546
Thank you for selecting American Standard...the benchmark of fine quality for over 100 years. To ensure that your
installation proceeds smoothly--please read these instructions carefully before you begin.
BEFORE YOU BEGIN....
Local building codes vary by location. Observe all local plumbing and building codes.
Your new bath is shipped to you after careful inspection.
To ensure maximum performance and pleasure from this product, please follow the instructions and cautions.
NOTE: Take extra care in handling surfaces of the bath. Use only non-abrasive cloths to avoid scratching.
!
TOOLS & MATERIALS REQUIRED
TOOLS:
• Level
• Square
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
NOTE: Must purchase Drain Kit 1614.305.YYY which contains matched nish metal
*
• Standard Woodworking Tools
• Personal Safety Equipment
• Caulking Gun
• Drill
• Hole Saw
overow cover and drain.
MATERIALS:
• Silicone Caulking
• Tub & Tile Caulk
ROUGH-IN INFORMATION: FREESTANDING TUB
Model 2546
34"
(864 mm)
38-13/16"
(968 mm)
(80 mm)
9/16"
(14 mm)
3-1/8"
3-1/8"
(80 mm)
26-1/4"
(666 mm)
(620 mm)
13/16"
(21 mm)
16-3/4"
(425 mm)
(65 mm)
24-7/16"
2-9/16"
19-3/8"
(492 mm)
68"
(1727 mm)
ø2-3/16"
(55 mm)
57-1/4"
(1454 mm)
2-1/4"
(57 mm)
REMOVABLE ACCESS PANEL
18-11/16"
(475 mm)
2-1/4"
(57 mm)
36"
(914 mm)
SAVE FOR FUTURE USE
GENERAL SPECIFICATIONS FOR
2546 FREE STANDING BATH
INSTALLED SIZE
68 x 36 x 24-7/16 in.
(1727 x 914 x 620mm)
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
38-13/16 x 16-3/4 In. (986 x 425mm)
57-1/4 x 26-1/4 In. (1454 x 666mm)
WATER DEPTH TO OVERFLOW
FLOOR LOADING
46 Lbs./Sq.Ft. (225 Kgs./Sq.m)
(PROJECTED AREA)
All product names listed herein are trademarks of AS America, Inc. unless otherwise noted.
© AS America, Inc. 2018
163 Lbs. (74 Kg.)
782 Lbs. (355 Kg.)
74 Gal. (280L)
17 In. (431mm)
755506-100
NOTE: Tub water fittings can be installed in one of 3 ways; Wall Mounted, Floor Mounted or Deck Mounted.
Location of the access panel must be considered BEFORE installation of the tub. The tub access
panel must be accessible if connecting deck mount llers. Drain connection can be mounted
through the access panel or through the oor.
1
INSTALLATION INSTRUCTIONS:
Place the tub on a finished, level floor in the desired location.
Using a marker, trace the outline of the tub drain hole onto the floor.
NOTE: If using existing P-Trap location, then skip to Step 3.
2
3
4
Install the P-Trap in the marked drain location. P-Trap is installer provided.
Place the tub again in the desired location with the drain hole directly in line with the P-trap.
Using an erasable marker or pencil, trace the outline of the tub on the oor (see Fig. 1).
FIG. 1
Using the adjustable feet on the underside of the tub, ensure that the tub is level.
Ensure that there is a gap between the tub base and the floor. Gap shall not exceed 3/16" (5mm). (See Fig. 2)
3/16" MAX
(5mm)
FINISHED FLOOR
FIG. 2
2
755506-100
Loading...