American Standard 2531.016, 2530.016, 2529.016 User Manual
NEOLO™ ELONGATED FV TOILET
• Elongated ush valve toilet
• Vitreous china
• Low consumption (6.0 Lpf/1.6gpf)
• Wall outlet elongated bowl, angle back and base
• Siphon jet ush action
• Fully glazed 2" ballpass trapway
• 10" x 13" water surface area
• 1-1/2" inlet spud
• 4 bolt caps
• 100% factory ush tested
❏ 2529.016 Elongated bowl only, top spud,
wall outlet
❏ 2530.016 Elongated bowl only, back spud,
wall outlet
❏ 2531.016 Elongated bowl only, back spud,
wall outlet, integral seat
NEOLO™
ELONGATED FLUSH VALVE TOILET
VITREOUS CHINA
Nominal Dimensions:
673 x 375 x 375mm
(26-1/2" x 14-3/4" x 14-3/4")
Recommended working pressure – between
30 psi at valve when ushing and 80 psi static
Fixture only, less seat, bolt caps, and ush valve
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.2 for Vitreous China Fixtures
To Be Specied:
❏ Color: ❏ White
❏ Seat: Olsonite #95 open front seat less cover
❏ Seat: Church #9500C open front seat less cover
❏ Seat: Pressalit seats for American Standard,
closed front seat with cover (thermoset
compound material).
❏ Alternate Seat:
❏ Flush Valve:
❏ American Standard Selectronic™ #6065.161.002
DC Power(Top Spud)
❏ American Standard Selectronic™ #6065.262.007
DC Power (Back Spud)
❏ American Standard Selectronic™ #6067.262.007
AC Power (Back Spud)
❏ American Standard Selectronic™ #6068.262.007
Multi AC Power (Back Spud)
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
© 2008 AS America Inc.
M51
Revised 11/08
ELONGATED FLUSH VALVE TOILET
FINI SHED WALL
FINI SHED
FLOO R
521m m
(20- 1/2)
267m m
(10- 1/2)
76mm
(3)
108m m
(4-1 /4)
673m m
(26- 1/2)
470m m
(18- 1/2)
375m m
(14- 3/4)
C/L OF
OUTL ET
375m m
(14- 3/4)
222m m
(8-3 /4)
152m m
(6)
13mm (1/2)
375m m
(14- 3/4)
C/L OF SE AT POS T HOL E
140m m (5- 1/2) C ENTER S
660m m
(26)
C/L OF 1/ 2" DIA . BOL T
HOLE S ON 140mm (5-1/ 2) CEN TERS
1-1/ 2" SP UD
121 mm
(4-3 /4)
1" N .P.T. OR C. W.T.
SUPP LY TO FLUSH VALV E
FINI SHED WALL
1-1/ 2"
SPUD
70mm (2-3 /4)
DIA. HOLE
IN W ALL
191m m (7- 1/2)
DIA. HOLE
IN W ALL
INTE GRAL SEAT
(253 1.016 )
FINI SHED
FLOO R
375m m
(14- 3/4)
222m m
(8-3 /4)
152m m
(6)
521m m
(20- 1/2)
267m m
(10- 1/2)
108m m
(4-1 /4)
225m m
(8-7 /8)
673m m
(26- 1/2)
470m m
(18- 1/2)
375m m
(14- 3/4)
C/L OF
OUTL ET
13mm
(1/2 )
C/L OF SE AT POS T HOLE
140m m (5- 1/2) C ENTERS
(253 0.016 )
C/L OF 1/ 2" DIA . BOLT
HOLE S ON 140mm (5-1/2 ) CEN TERS
FINI SHED WALL
1-1/ 2"
SPUD
121mm
(4-3/4)
1" N.P.T. OR
C.W.T. SUPPLY
70mm (2-3 /4)
DIA. HOLE
IN W ALL
191m m (7- 1/2)
DIA. HOLE
IN W ALL
572m m
(22- 1/2)
610m m
(24)
95mm
(3-3 /4)
OPEN ING I N WALL
38mm (1-1 /2) DI A.
INTE GRAL SEAT
(253 1.016 )
FOR WALLS UP TO 25mm (1") IN THI CKNES S;
FOR EACH 25mm ( 1-INCH ) ADD ITIONA L THI CKNESS
OF W ALL A DD 25m m (1") TO T HIS DI MENSI ON
FINI SHED
FLOO R
375m m
(14- 3/4)
222m m
(8-3 /4)
521m m
(20- 1/2)
267m m
(10- 1/2)
108m m
(4-1 /4)
225m m
(8-7 /8)
673m m
(26- 1/2)
470m m
(18- 1/2)
375m m
(14- 3/4)
C/L OF
OUTL ET
13mm
(1/2 )
C/L OF SE AT POS T HOLE
140m m (5- 1/2) C ENTERS
(253 0.016 )
C/L OF 1/ 2" DIA . BOLT
HOLE S ON 140mm (5-1/2 ) CEN TERS
2529.016 2530.016
NEOLO™
VITREOUS CHINA
© 2008 AS America Inc.
NOTES:
WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITEFELT (WAX RING NOT RECOMMENDED) .
TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM
BREAKER ON FLUSH VALVE, THE PLUMBER MUST VERIFY
DIMENSIONS SHOWN FOR SUPPLY ROUGHING.
FLUSH VALVE NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
IMPORTANT: Dimensions of xtures are nominal and may vary within
the range of tolerances established by ANSI Standard A112.19.2. These
measurements are subject to change or cancellation. No responsibilit y is
assumed for use of superseded or voided pages.
M52
Revised 11/08
Loading...