American Standard 2506.011 User Manual

AhtM'eaiii Shmia/rd

Installation

Instructions

MOMENTS

2506.011

Monoblock Bidet Faucet with

EverClean™ Finish & Speed Connect™ Drain

Congratuiations on purchasing your American Standard faucet with the EverCiean finish and Speed Connect drain, two features found only on American Standard faucets.

EverClean Finish

• One wipe effortlessly removes spots.

• Eliminates the need for cleaners and scrubbing.

• Permanent surface protectant remains beautiful

for the life of the faucet.

• EverClean™ available on: Polished Chrome, Satin Nickel, Stainless Steel, Polished Brass (or any combination of these finishes)

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

Speed Connect Drain*

• Fewer parts, installs in less time.

• Never needs adjustment.

• Guaranteed to seal properly the first time, every time,

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin

Recommended tools

Screwdriver Chennel Locks Adjustable Wrench

INSTALL FAUCET CAUTION

'Hirn off hot and cold water supplies before beginning.

Certified to comply with ANSI A112.18.1

M968936

Seat SEAL (1J into under side of FAUCET BASE [2). Feed FAUCET SUPPLIES (3). MOUNTING STUD (4) and DRAIN

CABLE ASSEMBLY (8) through the mounting hole of lavatory or mounting surface. Fig. A

From below, Dush GASKET 17) and RETAINING WASHER (5) onto MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (6), pulling faucet to front of sink, so SUPPLIES (3) rests against mounting hole. Before final tightening, make sure collar on MOUNTfNG NUT

Fig. B.

Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6) to complete faucet mounting.

(6) is seated into STAINING WASHER (5).

MOUNTING SURFACE

Fig. B

Fig. A

GROOVE (FAUCET

BASE)

COLLAR ON

MOUNTING NUT

POP-UP DRAIN

Remove CLEAR PLASTIC COVER (1]. Remove CARDBOARD SPACER (2) from under

DRAIN POP-UP (3). Tighten TAILPIECE (4) on DRAIN BODY before

installing DRAIN BODY. Fig. B.

REMOVE FLANGE

Thread FLANGE (1J counter-clockwise and remove FLANGE (11 and FOAM GASKET (2) from drain body. Fig. A.

Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B.

INSTALL DRAIN FROM BELOW FIXTURE

From under side of BIDET install DRAIN BODY (1) up through drain outlet.

Note: No plumber's putty

or caulk is required. The CABLE ATTACHMENT POINT (2) must face towards the rear of the BIDET.

Install FOAM GASKET (3) and FLANGE (4l onto drain body from above BIDET and tighten FLANGE (4) firmly.

FLANGE GASKET

Check DRAIN FLANGE in BIDET to ensure that

WHITE FOAM GASKET (3) is fully compressed

and not visible. Fig. A.

POP-UP KNOB m must be fully down. Fig. B.

TIGHTEN LOCKNUT

Tighten LOCKNUT (1) firmly with Adjustable Wrench or Channel Locks.

ATTACH CABLE CONNECTOR

Thread CABLE CONNECTOR (1J clockwise onto DRAIN BODY CONNECTION [2) and hand tighten. Fig. A.

Your new POP-UP DRAIN installation is now complete. Fig. B.

Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B.

CHECK OPERATION OF POP-UP

Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.

Note: If STOPPER (2) does not open and close properly then refer

to the “troubleshooting section” of these instructions.

MAKE WATER SUPPLY ANO WASTE CONNECTIONS

Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect

left SUPPLY (TJ to Hot (Marked with a Red Band] and right supply

to COLD [2) wall supply.

Faucet supplies are 2D” long from faucet base.

Note: If additional supply length is required, installer must

purchase additional parts separately.

Important: If SUPPLY HOSES ¡1, 2J are to long, loop as

illusP'ated to avoid kinking.

Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet.

APPROX.

COMPRESSION

M968936

+ 4 hidden pages