American Standard 2264.702 User Manual
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure
Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE:
If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE:
Mounting surface must be clean and level before new toilet is installed!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90˚,
and slide into place 6" (152 mm) apart and
parallel to wall.
S A V E F O R F U T U R E U S E
32
ROUGHING-IN DIMENSIONS:
NOTE:
Distance from wall to closet flange centerline must
be as listed below:
CLOSET FLANGE
CLOSET BOLTS
730489-100 Rev. B
12"
(305mm)
FINISHED WALL
FINISHED
FLOOR
Saniwares
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY
HANDLE WITH CARE!
NOTE:
Pictures may not exactly define contour of china and components.
!
REPERTOIRE 2266/2483
HERITAGE 2176
ANTIQUITY 2264/2464
WILLIAMSBURG 2264.702
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes
INSTALLATION INSTRUCTIONS
For Two-Piece Toilets with Aquameter™ Fill Valve
SUP PLY A S
REQ UIRED
12
(305mm)
P r od u c t n a m e s l i s te d h er e i n a r e tr a d e ma r k s o f A me r i c an S t an d a r d I n c .
© Am e r i ca n S ta n d a rd I n c. 2 0 06
WAX RING
SEALANT
5
4
7
6
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent
damage), and install wax ring evenly around
waste flange (horn), with tapered end of ring
facing toilet. Apply a thin bead of sealant
around base flange.
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange
so bolts project through mounting holes.
b. Loosely install mounting clip (for Heritage only), retainer
washers and nuts. Side of washers marked "THIS SIDE UP"
must
face up!
c. Position toilet squarely to wall and, with a rocking motion,
press bowl down fully on wax ring and flange. Alternately tighten
nuts until toilet is firmly seated on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install covers on washers. (If necessary, cut bolt height to
size before installing caps.)
c. Smooth off the bead of sealant around base. Remove excess
sealant.
INSTALL TANK
a. Install large rubber gasket over
threaded outlet on bottom of tank and
lower tank onto bowl so that tapered
end of gasket fits evenly into bowl
water inlet opening.
b. Insert tank mounting bolts and
rubber washers from inside tank,
through mounting holes, and secure
with metal washers and nuts.
c. With tank parallel to wall,
alternately tighten nuts until tank is
snugged down evenly against bowl
surface.
INSTALL TOILET SEAT
Install toilet seat in accordance with
manufacturer's directions.
WASHER
MOUNTING
CLIP
NUT
NUT
CLOSET
BOLT
CLOSET
BOLT
WASHER
HERITAGE
REPERTOIRE, ANTIQUITY,
& WILLIAMSBURG
BOLT CAP
BOLT CAP COVER
RUBBER
GASKET
TANK MTG.
BOLTS
NUT
WASHER
FLANGE
!
- 2 -
!
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
RUBBER
WASHER
730489-100 Rev. B 730489-100 Rev. B 730489-100 Rev. B
Loading...