American Standard 2257.103 User Manual
AFWALL™ ELONGATED TOILET
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE
BUILDING FACILITIES - CHECK LOCAL CODES.
When installed so top of seat is 432 to 483mm (17" to 19") from the
finished floor.
BARRIER FREE
• Flush valve toilet
• Vitreous china
• Low-consumption (6.0 Lpf/1.6 gpf)
• Wall-mounted elongated bowl
• Fully glazed trapway
• Direct-fed siphon jet action
• 1-1/2" inlet spud
• Fully-glazed 2-1/8" trapway
• 10" x 12" water surface area
• 100% factory ush tested
❏ 2257.103 Elongated bowl only, top spud
Component Parts:
❏ 047007-0070A Inlet Spud (furnished with bowl)
Nominal Dimensions:
635 x 375 x 381mm
(25" x 14-3/4" x 15")
AFWALL™ ELONGATED
FLUSH VALVE TOILET
VITREOUS CHINA
Recommended working pressure – between
30 psi at valve when ushing and 80 psi static
Fixture only, less seat, bolt caps, and ush valve
Compliance Certications Meets or Exceeds the Following Specications:
• ASME A112.19.2 for Vitreous China Fixtures
To Be Specied:
❏ Color: ❏ White
❏ Seat: 5901.100 American Standard Seat
❏ 5901.110 American Standard Seat with EverClean
❏ Alternate Seat: 5905.100 Heavy Duty
American Standard Seat
❏ 5905.110 Heavy Duty American Standard Seat
with EverClean
❏ Flush Valve:
❏ American Standard Selectronic™ #6065.161.002
DC Power (Top Spud)
❏ Carrier Fitting (by others):
SEE REVERSE FOR ROUGHING-IN DIMENSIONS
®
© 2008 AS America Inc.
M77
Revised 11/08
FIN IS HED W ALL
470 mm
(18 -1 /2)
C/L OF SE AT PO ST
HOL ES 140 mm
(5- 1/2) C ENTER
635 mm
(25 )
73m m
(2- 7/ 8)
133mm
(5-1/4)
191mm
(7-1/2)
292mm
(11-1/2)
(4) 22mm
(7/8)
HOLES
375 mm
(14 -3 /4)
C/L OF
OUTLET
121 mm
(4- 3/ 4)
FINISHED
FLOOR
32mm
(1-1/4)
381mm
(15)
1" N.P.T. OR C.W.T. SUPPLY
AS REQUIRED TO FLUSH VALVE
330mm
(13)
19mm
(3/4)
133mm
(5-1/4)
95mm
(3-3/4)
70mm
(2-3/4)
1-1/2 SPUD
C/L
229mm
(9)
2257
BARRIER FREE
AFWALL™ ELONGATED
FLUSH VALVE TOILET
VITREOUS CHINA
© 2008 AS America Inc.
NOTES:
● Toilet designed to meet ADA handicapped standards with seat height set at 432 to
483mm (17" to 19") from nished oor.
WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-FELT (WAX RING
NOT RECOMMENDED).
SUGGESTED 2mm (1/16) CLEARANCE BET WEEN FACE OF WALL AND BACK OF BOWL.
TO COMPLY WITH AREA CODE GOVERNING THE HEIGHT OF VACUUM BREAKER ON
THE FLUSH VALVE, THE PLUMBER MUST VERIFY DIMENSIONS SHOWN FOR SUPPLY
ROUGHING.
FLUSH VALVE NOT INCLUDED WITH FIX TURE AND MUST BE ORDERED SEPARATELY.
CARRIER FITTING AS REQUIRED TO BE FURNISHED BY OTHERS.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORT.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of
tolerances established by ANSI Standard A112.19.2.
These measurements are subject to change or cancellation. No responsibility is assumed for
use of superseded or voided pages
M78
Revised 11/08
Loading...