American Standard 4077.014 Tank, 2067.014, 3110.016 Bowl, 2219.014 Elongated, 3225.016 User Manual

...

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl. b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply! c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases. d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area. NOTE: Mounting surface must be clean and level before new toilet is installed!

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90°, and slide

into place 6" (152 mm) apart and parallel to wall.

CLOSET FLANGE

CLOSET BOLTS

730945-100 Rev. C

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

P r o du c t n a m e s li s t e d h e re in a r e t r ad em a r k s o f A me r i c a n S ta nd a r d I n c . © A me r i c a n S t a nd a r d I n c . 20 0 7

NOTE: Pictures may not exactly define contour of china and components.

S A V E F O R F U T U R E U S E

INSTALLATION INSTRUCTIONS CARE AND MAINTENANCE

Skyline Champion®4 2-piece Toilets

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Hacksaw Wax Ring/Gasket Flexible Supply Tube 1/2" Deep Well Nut Driver or Closet Bolts Tape Measure Carpenters Level Deep Well Socket Wrench

Recommended fitting type for back-to-back installations.

Depending upon your plumbing and venting conditions, the flow from

the Champion in a back-to-back installation may create a vacuum on the system and draw water from the opposing bowl. The National Standards Plumbing Code prohibits the use of a cross fitting for drainage as throw over is possible. The code does approve a directional "Y" style fitting with proper venting to direct the water downward and away from the other toilet.

NOTE: BACK-TO-BACK INSTALLATION

MODEL A B C D

DIMENSIONS

2067.014 Elongated Right Height™

2-pc Toilet

2112.014 Round Front Normal Height

2-pc Toilet

18-1/ 2" 470mm

16-1/ 2" 419mm

30-3/ 8" 772mm

34-3/ 8" 873mm

16-1/ 2" 419mm

15-1/ 4" 387mm

28-3/ 8" 721mm

33-1/ 8" 841mm

2219.014 Elongated Normal Height

2-pc Toilet

18-1/ 2" 470mm

15-1/ 4" 387mm

30-3/ 8" 772mm

33-1/ 8" 841mm

ROUGHING-IN DIMENSIONS: Right Height™ Elongated Two Piece Toilet Normal Height Round Front Two Piece Toilet Normal Height Elongated Two Piece Toilet

FIN ISH ED WAL L

19m m ± 6m m (1 ± 1 /4)

FIN ISH ED FLO OR

305 mm

(12 )

C/L OF OU TLE T

83m m

(3- 1/4 )

235 mm (9- 1/4 )

C/L OF SE AT POST HO LES 140 mm (5- 1/2 CENTER S)

362 mm

(14 -1/ 4)

264mm

(10-3/8)

16m m

(5/ 8)

498 mm

(19 -5/ 8)

SUP PLY

REQ 'D

254 mm

(10 )

152 mm

(6)

254 mm

(10 )

356 mm

(14 )

2067.014 Right Height™ Elongated: 3225.016 Bowl and 4077.014 Tank

2112.014 Round Front: 3110.016 Bowl and 4077.014 Tank

2219.014 Elongated: 3121.016 Bowl and 4077.014 Tank

730945-100 Rev. C

WAX RING

SEALANT

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes. b. Loosely install retainer washers and nuts. Side of washers marked "THIS SIDE UP" must face up!

- 2 -

CLOSET

BOLT

NUT

TAPERED WASHER

FLANGE

MANIFOLD INSIDE WATERWAY - DO NOT REMOVE

INSTALL TOILET

a. Position toilet squarely to wall and, with a rocking motion,

press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor.

CAUTION:

DO NOT OVERTIGHTEN NUTS

OR BASE MAY BE DAMAGED!

b. Install caps on washers. (If necessary, cut bolt height to size before installing caps.) c. Smooth off the bead of sealant around base. Remove excess sealant.

CLOSET BOLT

NUT

WASHER

BOLT CAP

Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.

CAUTION: DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE.

CAUTION: Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding.

These parts must be used as illustrated to insure water-tight connection. Use of existing coupling nut may result in water leakage. Water supply tube or pipe must extend at least 1/2" inside threaded shank of valve (does not apply to flanged tubing).

Use existing coupling nut and washer.

Use existing spiral cone washer. Fluidmaster cone washer may not seal completely on spiral type supply line.

Captive cone washers already included. No additional washers needed.

METAL/COPPER

FLARED TUBING

METAL FLANGED

TUBING

METAL SPIRAL

TUBING

VINYL/BRAIDED

CONNECTOR

LOCK NUTLOCK NUT LOCK NUT LOCK NUT

COUPLING NUT

EXISTING COUPLING NUT

COUPLING NUT

WATER SHUT-OFF

CONE WASHER

EXISTING CONE WASHER

EXISTING WASHER

INSTALL TANK

a. Install large rubber gasket over threaded outlet on bottom of tank and lower tank

onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening, and tank mounting bolts go through mounting holes. Secure with metal washer/nuts.

b. With tank parallel to wall, alternately tighten hex nuts until tank is snugged down

evenly against bowl surface.

Recommended tool: Deep socket tool included in tank kit.

CAUTION:

INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.

DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT! DO NOT SPIN BOLTS WITH SCREWDRIVER

RUBBER GASKET

TANK MTG. BOLTS PREINSTALLED

WASHER/NUT

CLOSE T FLANG E

+ 3 hidden pages