American Standard 2064.90X User Manual
Installation
Instructions
SERIN
™
2064.90X
DECK MOUNT BATH FILLER
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended Tools
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Tubing Cutter
*Wrench
*Hex key
*Supplied with Fitting
ROUGHING-IN DIMENSIONS
9-1/2"
(240mm)
MOUNTING
SURFACE
6-3/4"
(170mm)
9-3/4"
(247mm)
1-3/16" MAX.
(30mm) MAX.
3/4-14 MALE
N.P.T. INLETS
2-3/4"
(71mm)
1-1/8 D.
3-1/4" D.
(82mm) D.
(H)
1-1/16 D.
(27mm) D.
Certified to comply with ANSI A112.18.1M
M968830 Rev.1.4
6-1/2" to 12"
(165mm to 305mm)
2" D.
(52mm) D.
3'
(76mm)
(C)
12 MAX.
(305mm)
2-1/16" D.
(52mm) D.
1-1/2 MAX.
(38mm) MAX.
1-3/16 D.
(30mm) D.
SPOUT ASSEMBLY
1
CAUTION
Turn off hot and cold water
supplies before beginning.
Install RUBBER RING (1) into ESCUTCHEON RING (2) and
place over mounting hole.
Insert SPOUT SHANK (3) through center hole of MOUNTING LEDGE.
Make sure that the RUBBER RING (1) is properly seated in RECESS
of ESCUTCHEON RING (2).
Assemble RUBBER WASHER (4) and BRASS WASHER (5) onto
SHANK (3). From underside of ledge secure SPOUT (7) into position
with LOCKNUT (6).
7
2
RECESS
3
1
MOUNTING
SURFACE
PREPARE TUBE AND TEE ASSEMBLY
2
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and 12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
4
3
1
5
6-1/2" to 12"
(165mm to 305mm)
MOUNTING
SURFACE
3
4
4
2
5
6
NOTE
VALVE inlet is
3/4-inch NPT male.
VALVE ASSEMBLY
3
Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks.
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)
into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is
properly seated on SHANK (6). Push COUPLING (8) into TEE (5) and attach to
SPOUT SHANK (6) and tighten using a 10mm (3/8'') hex wrench. Tighten
COUPLING (8) using a 10mm (3/8") Hex wrench. (FOR 2064.901). Use
COUPLING (8a) for fitting less spray.
Thread of VALVE BODY (4) should extend at least 5/16 inch above MOUNTING
SURFACE (11). If necessary, adjust LOCKNUT (1).
Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) with WRENCH supplied to secure VALVE (4) position.
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten
COUPLING NUT (13) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
9
11
2
1
MOUNTING
SURFACE
Wrench
5/16'' MIN.
10
4
9
10
HOT
8a
11
MOUNTING
SURFACE
9
10
4
7
12
13
3
5
8
13
6
12
4
COLD
INSTALL HANDLES
4
Push ADAPTER (1) on VALVE STEM (2). See figure "A". Tighten
STEM SCREW (3) to secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (4).
Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5)
until snug against mounting surface
SERVICE
5
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Thread counter-clock wise HANDLE BASE (1) to remove
HANDLE ASSEMBLY (2) from ESCUTCHEON BASE (3).
Use a flat blade screw driver to remove SPRING CLIP (4).
Lift STOP WASHER (5), turn 90˚ and replace.
Replace SPRING CLIP (4).
Reinstall HANDLE ASSEMBLY (2).
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90˚.
.
SPLINE
END UP
Figure "A"
1
5
3
THREAD ON
TO DECK
4
TOP
ADAPTER
1
3
2
5
2
90˚
VALVE
4
M968830 Rev.1.4
Loading...