American Standard 2064.724 User Manual
ONE SHOWER SYSTEM
Installation
Instructions
Certified to comply with ANSI A112.18.1
2064.724
Recommended Tools & Materials
ROUGHING-IN DIMENSIONS
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Electric Drill
10mm (3/8)
Drill Bit
Pencil
Phillips Screwdriver
76mm
(3)
FINISHED WALL
95mm
(3-3/4)
54mm
(2-1/8)
38mm
(1-1/2)
19mm
(3/4)
33.5mm
(1-3/16D.)
96mm
(3-3/4)
41mm
(1-5/8)
586-595mm
(23-1/8, 23/3/8)
620mm
(24-3/8)
FINISHED FLOOR
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
915mm
(36)
1219mm
(48)
TO
Hammer
32mm
(1-1/4)
13mm
(1/2)
1/2" NPT
RUBBER GASKET
FINISHED
WALL
1/2" NPSM HOSE
CONNECTION
53mm
(2-1/16)
60mm
(2-3/8")
25mm
(1")
1/2" NPSM
151mm
(6")
203mm
(8")
65mm
(2-1/2")
(48" - 60") (OPTIONAL)
TO FINISHED FLOOR
59"
Teflon TapeLevel
1
Turn off hot and cold water
supplies before beginning.
CAUTION
INSTALL WALL SUPPLY
1/2" NPT
APPLY SEALANT
OR TEFLON TAPE
1
Supply to WALL SUPPLY (1) is 1/2" NPT. See rough-in above for detailed information.
Install RUBBER SEAL (2) onto WALL SUPPLY (1).
Apply sealant or teflon tape to threads of 1/2" NPT supply nipple. Thread WALL SUPPLY (1)
onto supply nipple making a water tight seal. WALL SUPPLY (1) with RUBBER SEAL (2)
should be tight against finished wall.
2
M 9 6 8 9 2 7 R e v . 1 . 1
2
591mm
(23-1/4)
591mm
(23-1/4)
591mm
(23-1/4)
The ADJUSTABLE SHOWER BAR (1) works best if secured to a wall stud or cross brace
within the wall, using the SCREWS (2) supplied.
If the ADJUSTABLE SHOWER BAR (1) is to be installed on a tile the ANCHORS (3) and
SCREWS (2) should be used.
Install RUBBER WASHER (5) in recess of MOUNTING SUPPORT (4). Secure
MOUNTING SUPPORT (4) to wall with SCREWS (2).
For installations on tiled walls: Use ANCHORS (3) and SCREWS (2) for securing MOUNTING
SUPPORT (4) to finished wall. The diameter and depth of the mounting hole should be
10mm (3/8”) dia. and 50mm (2”) deep. Insert the the ANCHORS (3) and tap them with
hammer until flush with face of finished wall.
Determine desired height and location (optional) and mark a center line. If MOUNTING
SUPPORT (4) is secured to a stud or cross brace drill small pilot holes for SCREWS (2).
IMPORTANT: Make sure that vertical center line is level.
INSTALL WALL BRACKETS
5
3
2
3
1
5
C/L
C/L
FINISHED WALL
RECESS IN
MOUNTING
SUPPORT
FROM CENTER TO
CENTER OF WALL
BRACKETS
Install ADJUSTABLE SHOWER BAR (1) onto installed MOUNTING SUPPORTS (4).
Push ADJUSTABLE SHOWER BAR (1) flush against finished wall and tighten
SET SCREWS (5) with (2.5mm) HEX WRENCH (7) supplied to secure
ADJUSTABLE SHOWER BAR (1) to wall.
4
INSTALL ADJUSTABLE SHOWER BAR
INSTALL HOSE AND HAND SHOWER
13
11
12
8
10
9
2
7
4
4
5
Install SEAL (8) into COUPLING NUT (9). Connect COUPLING NUT (9) to WALL SUPPLY NIPPLE (10) and tighten.
INSTALL second SEAL (11) into SPRAY HOSE END (12) and connect HAND SHOWER (13) to SPRAY HOSE END (12).
Hand tighten.
3
M 9 6 8 9 2 7 R e v . 1 . 1 M 9 6 8 9 2 7 R e v . 1 . 1
Loading...