American Standard 2064.4 User Manual

Installation

Instructions

SERIN

™

2064.400

Bidet Faucet and Transfer Valve with

Speed Connect™ Drain

Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets.

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Roughing-in Dimensions

BIDET OUTLINE IS SYMBOLIC

DOUCHE SPRAY

3-7/8

TRANSFER VALVE

(FOR FLUSHING RIM OR SPRAY)

7/8 DIA.

ADJ. 1-1/4

TO 2-1/4

1-3/8

DIA.

5-1/2

FINISHED WAL L

2-1/8

DIA.

1-1/4 O.D. TAILPIECE

1-3/16

DIA.

1-1/4

MAX.

FINISHED FLOOR

8 TO 12

(C)

(H)

2-1/4

DIA.

4-1/4

FOR GROUND JOINT CONNECTION OR 1/2 " O.D. SLIP (INLETS)

REAR VIEW WITH

WALL REMOVED

Recommended tools

Certiﬁed to comply with ANSI A112.18.1

M968924 Rev.1.3

Screwdriver

Phillips Screwdriver

Adjustable Wrench

Plumbers' Putty or Caulking

Channel Locks

Tubing Cutter

BIDET FAUCET INSTALLATION

CAUTION

Turn off hot and cold water supplies before beginning.

Place RUBBER RING (10) into ESCUTCHEON (4).

Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From under side of mounting surface, install VALVE BODY (3, 3a) through valve mounting holes. Threads of VALVE BODY (3, 3a) should extent at least 5/16 of a inch above mounting surface top. Fig. A. Thread ESCUTCHEON (4) onto VALVE BODIES (3, 3a) until snug against internal stop. If necessary, adjust LOCKNUT (1).

Tighten LOCKNUTS (1) with WRENCH (5) (supplied) to secure VALVE BODIES (3, 3a).

Remove ESCUTCHEON (6), WASHER (7) and UPPER GASKET (8) from TRANSFER VALVE (9). Insert TRANSFER VALVE (9) into the center forward

Fig. A.

5/16'' MIN.

hole of BIDET.

Replace UPPER GASKET (8) and WASHER (7) and ESCUTCHEON (6) until it locks against internal stop. Position the side threaded outlet rearward and secure MOUNTING NUT (11).

SPRAY INSTALLATION

Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside of SPRAY BODY FLANGE (2) and secure with NUT (3).

3, 3a

Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1). Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet NIPPLE (7) of the TRANSFER VALVE (8).

Thread SPRAY CAP (9) onto SPRAY BODY (1).

MOUNTING SURFACE

2 1

BIDET

LEDGE

HOT

PUTTY

COLD

POP-UP DRAIN

Fig. A.

Fig. B.

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under DRAIN POP-UP (3).

Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY.

REMOVE FLANGE

Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body.

Fig. A.

Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3).

Fig. B.

Fig. A. Fig. B.

DRAIN BODY

INSTALL DRAIN FROM

BELOW FIXTURE

From under side of BIDET install DRAIN BODY (1) up through drain outlet.

Note: No plumber’s putty or caulk is required. The CABLE ATTACHMENT POINT (2) must face towards the rear of the BIDET.

Install FOAM GASKET (3) and FLANGE (4) onto drain body from above BIDET and tighten FLANGE (4) ﬁrmly.

FLANGE GASKET

Check DRAIN FLANGE in BIDET to ensure that WHITE FOAM GASKET (1) is fully compressed and not visible. Fig. A.

POP-UP ROD ASSEMBLY

Insert LIFT ROD GUIDE (1) and CABLE CONNECTOR (2) through rear hole, making sure SEAL WASHER (3) is

properly seated. Fig. B.

From below slip slot in MOUNTING NUT (4) over CABLE (5). Thread NUT (4) onto lift rod guide shank to secure ROD GUIDE (1) to bidet. Hand tighten only. Fig. B.

DRAIN OUTLET

Fig. A.

FLANGE

DRAIN

TIGHTEN LOCKNUT

Tighten LOCKNUT (1) ﬁrmly with Adjustable Wrench or Channel Locks.

Fig. B.

WHITE FOAM

GASKET NOT VISIBLE

ILLUSTRATION SHOWN LESS VALVES

SLOTTED MOUNTING NUT

M968924 Rev.1.3

ATTACH CABLE

CONNECTOR

Fig. A.

Fig. B.

Fig. C.

POP-UP KNOB (1) must be fully down. Fig. A.

Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. B.

Your new POP-UP DRAIN installation is now complete.

Fig. C.

Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. C.

CHECK OPERATION OF POP-UP

Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.

Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.

INSTALL DIVERTER KNOB

Push DIVERTER KNOB (1) onto HANDLE ADAPTER (2).

DOWN

1-1/4” O.D.

5 4

Push on RING (3) and tighten with SCREW (4).

Press on KNOB CAP (5). Note: Screwdriver gap is for disassembling and should point downwards.

TEE AND HOSE CONNECTION

Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2) to side of TRANSFER VALVE (3).

Install SEAL (4) into coupling nut of TEE (5) and tighten connection to ADAPTER (2).

Connect HOSE COUPLING NUTS (6) to Hot and Cold valve bodies and securely tighten.

WATER SUPPLY CONNECTION

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEPARATELY.

Connect water supply to VALVE BODIES (7,7a) with 1/2" IPS FLEXIBLE SUPPLIES (8) or 3/8" O.D. BULL-NOSE RISERS (9). Use adjustable wrench to tighten connections. Do not over tighten. Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.

Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS.

Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet.

OUTLINE OF BIDET

1/2" PIPE

THREAD

FLEXIBLE SUPPLIES

HOT

3/8 COMPRESSION CONNECTION

Front

COLD

CONNECT TO WASTE OUTLET

COUPLING NUT

3/8 O.D.

BULL-NOSE

RISERS

COMPRESSION NUT

FERRULE

M968924 Rev.1.3

+ 4 hidden pages