American Standard 18SB.9332200A.075 Installation Manual
INSTALLATION INSTRUCTIONS
9"
(229 mm)
1-3/8"
(35 mm)
4-3/4"
(120 mm)
16-1/2"
(420 mm)
22"
(559 mm)
19-15/16"
(508 mm)
8"
(203 mm)
27-1/4"
(692 mm)
30"
(762 mm)
CARE AND MAINTENANCE
CURVED APRON FRONT STAINLESS STEEL SINK
Flush Mount or Under Mount Sink
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of components.
Before installing the sink, inspect it for damage. DO NOT install a damaged unit.
Notify your American Standard distributor of any damage. Return sink in original packing.
OBSERVE LOCAL PLUMBING AND BUILDING CODES
RECOMMENDED TOOLS AND MATERIALS
Phillips Screwdriver
Regular Screwdriver
Pipe Wrench
Electric
Drill
Channel Locks
Adjustable Wrench
11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7 8 9 10
10'
Tape Measure
Tubing Cutter
Sealant
1 2 3 4 5 6 7 8 9 10 11
Square
Hacksaw
Saber Saw
Level
ROUGH-IN
* NOTE: Dimensions may vary. Please use the actual size of the sink that you will be installing in order to determine the
cutout dimensions for your countertop.
33" SINK 30" SINK
8"
(203 mm)
9"
(229 mm)
1-3/8"
(35 mm)
4-3/4"
(120 mm)
16-9/16"
(420 mm)
19-15/16"
(508 mm)
22"
(559 mm)
(768 mm)
30-1/4"
33"
(838 mm)
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
791679-100 Rev. C 1/18
MOUNTING OPTIONS
Sink can accommodate any standard 3-1/2" (89mm) sink outlet drain.
COUNTERTOP
Flush Mount
Installation *
Under Mount
Installation *
REPLACEMENT USE
When replacing an original unit be sure to shut off water supply before removing the lavatory or
disconnecting water supply lines and drain fittings. Original supplies and shutoff valves should be
replaced on installation.
INSTALLATION PROCEDURES
Typical installation includes cabinet support preparation, installation of faucet, connection of flexible water
supply lines, attachment of sink to cabinet, sizing and installation of drain, supplies to house water system.
Sink Mounting Provisions – Whether the sink is used for replacement or new installation, the cabinet area
beneath the sink must be reinforced to provide sufficient support.
CABINET SUPPORT PREPARATION
Important Note:
It is recommended that the installation be performed by a professional and shall be in accordance with all
local plumbing and building code requirements.
- 2 -
791679-100 Rev. C 1/18
FLUSH MOUNT or UNDER MOUNT INSTALLATIONS
1
DETERMINE MOUNTING OPTIONS
Determine if the sink will be flush mounted or under mounted. Next measure the actual size of the sink being
installed to determine cabinet opening dimensions and support frame location. (Also reference rough-in for
dimensions.) The cabinet opening should equal the maximum dimensions of the sink to ensure a minimum gap
between the sink apron and the cabinet. Support frame location is determined by type of sink installation being
performed.
FLUSH MOUNT INSTALLATION (SHOWN)
TOP SURFACE OF SINK & COUNTERTOP
ENSURE LEVEL BEFORE SECURING
HOT & COLD SUPPLIES
FRAME RUNNING
FRAME RUNNING
FRONT TO REAR
BOTH SIDES
SIDE TO SIDE
SINK
COUNTERTOP
- 3 -
791679-100 Rev. C 1/18
Loading...