American Standard 1660.200, 1660.300, 1660.431, 1660.430, 1660.441 User Manual

...

Installation Instructions

THREE WAY:

SHOWER SYSTEMS

TWO WAY OR THREE WAY IN-WALL DIVERTER

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

CAUTION: DO NOT SEAL ANY OUTLETS. DIVERTER

CANNOT BE USED AS A STOP VALVE.

TWO WAY

BODY

1660.300

1660.430

1660.431 TWO WAY:

1660.200

1660.440

1660.441

MAX

Certified to comply with ANSI A112.18.1M

50321B

ROUGHING-IN DIMENSIONS

NOTE: NO CONCEALED PIPING FURNISHED

2-9/16

THREE WAY

BODY

DISK

O-RINGS

ESCUTCHEON

(1660.200/.300)

LOWER

DISK

STEM

DISK

O-RING

CLIP

ESCUTCHEON

NUT

UPPER

DISK

SHAFT

HANDLE

ADAPTER

WASHER

HANDLE

SPRING

DECORATOR

INDEX

BUTTON

SHAFT O-RING

WASHER

RING

3-1/8

1-5/8

ALL CONNECTIONS 1/2" NPT

CAP

SEAL

HANDLE

SCREW

CAP

HANDLE

(1660.431/.441)

2-1/4

FINISHED

WALL

PLASTER

GUARD

MAX

HANDLE

(1660.430/.440

Printed in Germany

HANDLE

ADAPTOR

HANDLE

SCREW

HANDLE

SKIRT

HANDLE

SCREW

VANDAL-RESISTANT

INDEX CAP

VANDAL-RESISTANT

HANDLE SCREW

ROUGHING-IN

Turn off hot and cold water supplies before beginning.

CAUTION

See Roughing-in Drawing on reverse side. The port with the BATH TUB picture is the high flow.

The DIVERTER can be installed with the inlet rotated in any position.

Supply connections are 1/2" NPT connections.

For proper positioning the finished wall must be within side of PLASTER GUARD.

Connect water to valve. The reverse side of the body is marked with arrows.

CAUTION: Do not solder near the VALVE. Damage to the SEAL may occur.

Do not seal any outlets. The DIVERTER cannot be used as a stop valve.

For support use pipe braces secured to wooden braces.

TEST DIVERTER

Check that the DIVERTER operates correctly and does not leak.

DIVERTER

To do this, screw off the PLASTER GUARD, turn around, and insert using the fluted pin into the fluting on the DIVERTER SPINDLE and use as a diverter knob. Screw the PLASTER GUARD back on. Have the wall tiled only with the PLASTER GUARD screwed on.

INSTALL TRIM

(For 1660.200/.300, handles are

purchased separately.)

When finished tiling wall, remove PLASTER GUARD.

Place ESCUTCHEON on ESCUTCHEON HOLDER and screw HOLDER onto VALVE.

For 1660.430/.440 Series:

Push HANDLE ADAPTER onto STEM. Make sure arrow is up.

Assemble HANDLE and DECORATOR RING onto

ESCUTCHEON

HANDLE ADAPTER. Secure with HANDLE SCREW. Snap on HANDLE CAP. Check for leaks. To operate, turn the HANDLE clockwise or counter clockwise.

For 1660.431/.441 Series:

HANDLE

SKIRT

Assemble HANDLE SKIRT then HANDLE LEVER to ESCUTCHEON NUT STEM. Secure with HANDLE SCREW.

Push on INDEX BUTTON or screw on VANDAL RESISTANT INDEX CAP. Check for leaks. To operate, turn the HANDLE clockwise or counter clockwise.

ESCUTCHEON

NUT STEM

HANDLE

ADAPTER

HANDLE

SCREW

DIVERTER

SPINDLE

HANDLE

INDEX

BUTTON

PLASTER

GUARD

MAX

DECORATOR

RING

HANDLE

SCREW

VANDAL-RESISTANT

INDEX CAP

VANDAL-RESISTANT

HANDLE SCREW

CAP

SERVICE

To Replace O-Rings:

Turn off water supply.

For 1660.430/.440 Series:

Use a small screw driver to remove HANDLE CAP.

Remove HANDLE SCREW, DECORATOR RING, HANDLE and ADAPTER.

Unscrew ESCUTCHEON HOLDER and

remove HOLDER and ESCUTCHEON.

Unscrew CAP and remove STEM,

SPRING and SEALS.

Remove old DIVERTER elements and

install new parts.

Replace remaining parts in reverse order.

For 1660.431/.441 Series:

Remove INDEX BUTTON (or unscrew VANDAL RESISTANT INDEX CAP).

Remove HANDLE SCREW, LEVER HANDLE and HANDLE SKIRT.

For toll-free information and answers to your questions, call:

Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time

IN CANADA 1-800-387-0369 (TORONTO 1-416-536-5609)

HOTLINE FOR HELP

1 (800) 442-1902

DISK

O-RING

LOWER

DISK

O-RING

UPPER

DISK

SHAFT

WASHER

SPRING

SHAFT O-RING

WASHER

Unscrew ESCUTCHEON HOLDER and remove HOLDER and ESCUTCHEON.

Unscrew CAP and remove STEM, SPRING and SEALS. Remove old DIVERTER elements and install new parts. Replace remaining parts in reverse order.

CAP

50321B