
Installation
Instructions
LUXURY SHOWER
EXTENDER BODY SPRAYS
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Recommended Tools
1660.130
1660.140
1660.130 1660.140
Certified to comply with ANSI A112.18.1
M968617 Rev.1.2
Flat Blade Screwdriver
ROUGHING-IN DIMENSIONS
ALL CONNECTIONS 1/2" NPT
74mm D.
(2-15/16")
1660.130 Multifunction
Round Body Spray
26mm
(1")
2-1/4" DIA.
(57mm) Hole Saw
(75.6-82.6mm)
2-15/16" - 3-1/4"
12mm
(1/2")
75mm
(3")
Teflon Tape
Electric Drill
1660.140 Multifunction
Square Body Spray
15°
FINISHED WALL
54mm D.
(2-1/8")
57mm D.
(2-1/4")
HOLE SIZE
(63.6-70.6mm)
2-1/2" - 2-3/4"
35mm
(1-3/8")
1/2" NPT

INSTALL SUPPLY PIPING
1
Provide a “Installation Hole” 2-1/8" - 2-3/8" DIA., (54-60mm) and 3-1/4", (83mm) deep. Note: The “Installation Hole”
must be clear to allow body spray clearance.
Install the ELBOW (1) on a support within the wall at the *dimension shown. Secure with
two M5 SCREWS (2) (not provided).
83mm
54-60mm
(2-1/8" - 2-3/8" DIA.)
(3-1/4")
CAUTION
1
{
“Installation Hole”
2
Turn off hot and cold water
supplies before beginning.
54-60mm
(2-1/8" - 2-3/8" DIA.)
“Installation Hole”
FINISHED WALL
82.6mm
(3-1/4")
2
*63.6-70.6mm
(2-1/2" - 2-3/4")
*75.6-82.6mm
(2-15/16" - 3-1/4")
WALL SUPPORT
1
INSTALL PLASTER GUARD
2
Make sure the O-RING (3) is installed on the PLASTER GUARD (1).
Install the PLASTER GUARD (1) into ELBOW (2). Note: The finished wall must be between the Min. & Max.
lines on the PLASTER GUARD (1).
Complete all tiling and wall work. When walls are finished remove PLASTER GUARD (1).
FINISHED WALL
1
MAX.
(LINE MARK)
MINIMUM
(LINE MARK)
REMOVE
INSTALL
3
1
2
3
2
M968617 Rev.1.2

INSTALL BODY SPRAY
3
Remove the PLASTER GUARD (1) if not already removed.
Make sure the O-RING (2) and FLANGE GASKET (6) are installed on the BODY SPRAY (3). Thread BODY SPRAY (3)
into the ELBOW (4).
Tighten BODY SPRAY (3) using WRENCH (5) supplied until flush against finished wall and FLANGE GASKET (6) is
compressed. Turn on water supply and test installed BODY SPRAY (3) for leaks and proper operation.
2
6
INSTALL ESCUTCHEON
4
Align ribs on back of ESCUTCHEON (1, 2), with slots in BODY SPRAY (3). Push ESCUTCHEON (1, 2) against BODY
SPRAY (3) until ESCUTCHEON (1, 2) snaps into place.
Turn on water supply and test installed BODY SPRAY (3) for leaks and proper operation.
2
3
5
4
1
5
FINISHED WALL
3
6
4
FINISHED WALL
ALIGNMENT RIBS ON
BACK OF ESCUTCHEON
SLOTS
3
1 2
2
1
CARE:
5
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
ALIGNMENT RIBS ON
BACK OF ESCUTCHEON
M968617 Rev.1.2