American Standard 0790.400, 0790.100, 0790.004, 0031.000, 0790.800 User Manual

1-1/4" O.D.

WASTE

24"

(610mm)

22"

(559mm)

SUPPLIES AS

REQUIRED

(152mm)

DRAIN

CHASE

OPEN

FLOOR

9-1/2"

(241mm)

20-1/4"

(514mm)

24"

(610mm)

FINISHED WALL

FINISHED

FLOOR

1-3/4" DIA.

STD. DRAIN

OUTLET

18-3/4" (476mm)

2-5/8"

(67mm)

(102mm)

5/8"

(16mm)

PED BASE

OUTLINE

PED TOP OUTLINE

35-1/2"

(902mm)

28"

(711mm)

3-3/4" (95mm)

7-1/2"

(191mm)

(152mm)

10"

(254mm)

3/8" (10mm) DIA.

BASE ANCHOR SCREW HOLES

ON 6" (152mm)

CTRS

3/8" (10mm) DIA.

SLAB ANCHOR SCREW HOLES

ON 18-3/4" (476mm)

CTRS

TOWN SQUARE® 24" PEDESTAL SINK

• American classic design

• Clean straight lines with classic ogee curves

• Rear overow

• Supplied with mounting kit

• Design-matched to Town Square xture

and faucets

• Right Height™ for greater comfort during use

• Made from reclay

❏ 0790.400 Faucet holes on 4" (102mm) centers ❏ 0790.800 Faucet holes on 8" (203mm) centers ❏ 0790.100 Center hole only

Nominal Dimensions: 24" x 20-1/4" x 35-1/2" (610 x 514 x 902mm)

Separate Components:

❏ 0790.004 Pedestal top 4" (102mm) centers ❏ 0790.008 Pedestal top 8" (203mm) centers ❏ 0790.001 Center hole only ❏ 0031.000 Pedestal only

TOWN SQUARE® 24"

PEDESTAL SINK

FIRECLAY

Bowl sizes:

14" (356mm) wide 11-3/4" (298mm) front to back 6-1/2" (165mm) deep

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.9M for Non-Vitreous

• CAN/CSA B45 Series

* See faucet section for additional models available

Ceramic Fixtures

To Be Specied:

❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Black ❏ Town Square Faucet:

❏ Centerset Lavatory Faucet: 2555.201 (shown) ❏ Widespread Lavatory Faucet: 2555.801

❏ Other Lavatory Faucet*: ❏ Faucet Finish: ❏ Supplies: ❏ 1-1/4" Trap:

NOTES:

DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TR AP ARE

SUGGESTED.

▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.

■ FOR REINFORCEMENT ONLY. TAKE ACTUAL DIMENSIONS FROM

FIXTURE. FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.9M. These measurements are subject to c hange or cancellation. No responsibility is assumed for use of superseded or voided pages.

Revised 2/08