American Standard 0780.800, 0780.100, 0780.400 User Manual

BARRIER FREE

1-1/4" O.D.

WASTE

24"

(610mm)

22"

(559mm)

SUPPLIES AS

REQUIRED

(152mm)

DRAIN

CHASE

OPEN

FLOOR

9-5/8"

(244mm)

21-1/4"

(540mm)

27"

(686mm)

FINISHED WALL

FINISHED

FLOOR

1-3/4" DIA.

STD. DRAIN

OUTLET

(102mm)

20-1/4" (514mm)

2-5/8"

(67mm)

(102mm)

5/8"

(16mm)

PED BASE

OUTLINE

PED TOP OUTLINE

36"

(914mm)

28"

(711mm)

3-3/4" (95mm)

(203mm)

(152mm)

10"

(254mm)

1-1/4" O.D. TAILPIECE

3/8" (10mm) DIA.

BASE ANCHOR SCREW HOLES

ON 6" (152mm)

CTRS

3/8" (10mm) DIA.

SLAB ANCHOR SCREW HOLES

ON 20-1/4" (514mm)

CTRS

TOWN SQUARE® 27" PEDESTAL SINK

• American classic design

• Clean straight lines with classic ogee curves

• Rear overow

• Supplied with mounting kit

• Design-matched to Town Square®

xture and faucets

• Right Height™ for greater comfort during use

• Made from reclay

❏ 0780.400 Faucet holes on 4" (102mm) centers ❏ 0780.800 Faucet holes on 8" (203mm) centers ❏ 0780.100 Center hole only

Nominal Dimensions: 27" x 21-1/4" x 36" (686 x 540 x 914mm)

Separate Components:

❏ 0780.004 Pedestal top 4" (102mm) centers ❏ 0780.008 Pedestal top 8" (203mm) centers ❏ 0780.001 Center hole only ❏ 0031.000 Pedestal only

TOWN SQUARE® 27"

PEDESTAL SINK

FIRECLAY

Bowl sizes:

15" (381mm) wide 12-1/2 (318mm) front to back 6-1/2" (165mm) deep

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.9M for Non-Vitreous Ceramic Fixtures

• CAN/CSA B45 Series

To Be Specied:

❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Silver ❏ Black ❏ Town Square Faucet: ❏ Centerset Lavatory Faucet: 2555.201 ❏ Widespread Lavatory Faucet: 2555.801 (shown)

❏ Other Lavatory Faucet*: ❏ Faucet Finish: ❏ Supplies: ❏ 1-1/4" Trap:

* See faucet section for additional models available

NOTES:

DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TR AP ARE

SUGGESTED.

▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.

■ FOR REINFORCEMENT ONLY. TAKE ACTUAL DIMENSIONS FROM

FIXTURE. FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.9M. These measurements are subject to c hange or cancellation. No responsibility is assumed for use of superseded or voided pages.

Revised 2/08