American Standard 0740.000 User Manual
BARRIER FREE
FINI SHED
WALL
OR
SPLA SH BA CK
COUN TERTO P
CUTO UT 38 4mm
(15- 1/8) DIA.
206m m
(8-1 /8)
419m m
(16- 1/2)
38mm
(1-1 /2)
MIN.
51mm
(2)
MIN.
B
A
C/L
1-1/ 4 O.D .
TAIL PIECE
1-1/ 4 O.D .
WAST E
203m m
(8)
159m m
(6-1 /4)
178m m
(7)
29mm
(1-1 /8)
COUNTERTOP
(BY OTHERS)
SEALING
COMPOUND
SUPPLIES
AS REQ'D.
305m m
(12)
*
254m m
(10)
*
FINI SHED
FLOO R
787mm
(31)
SUGGESTED
835mm
(32-7/8)
FAUCET
CENTER-S ET
SPREAD
A
27mm(1-1 /16)
32mm(1-1 /4)
B
102mm(4)
203mm(8)
L
of Faucet **
C
848mm
(33-3/8)
51mm
(2)
610mm
(24)
152mm
(6)
MAX.
BARRIER FREE
CLEARAN CE
686mm
(27)
MIN.
203mm
(8)
MIN.
229mm
(9)
MIN.
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
ENFIELD™ COUNTERTOP SINK
MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES
AND ANSI A117.1 ACCESSIBLE AND USABLE
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Install lavatory 864mm (34") from finished floor.
Lavatory installed 51mm (2") minimum from front edge
of countertop provides 686mm (27") knee clearance area.
• Decorative ogee rim detail round sink
• Made from vitreous china
• Self-rimming with cutout template supplied
• Center drain outlet
• Front overow
❏ 0740.000 Round Sink less Faucet Deck
Nominal Dimensions:
419mm (16-1/2") Round
Bowl Sizes:
324mm (12-3/4") round
152mm (6") deep
Compliance Certications Meets or Exceeds the
Following Specications:
• ASME A112.19.2M for
Vitreous China Fixture
ENFIELD™
COUNTERTOP SINK
VITREOUS CHINA
Shown with Hampton 8" Faucet (7881732.295)
To Be Specied:
❏ Color: ❏ White ❏ Bone
❏ Linen ❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
* See faucet section for additional models available
© 2008 AS America Inc.
NOTES:
* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TR AP
ARE SUGGESTED.
SPOUT MUST BE 4-5/8" LONG (min.) FOR ADEQUATE CLEARANCE
**
INTO SINK
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE
TEMPLATE SUPPLIED WITH SINK.
IN-FIELD ADJUSTMENT OF POP-UP ROD EXTENSION REQUIRED.
PROVIDE A 2-1/2"
SEALING COMPOUND SUPPLIED BY OTHERS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.2 These
measurements are subject to change or cancellation. No responsibilit y is
assumed for use of superseded or voided leaet.
J34
Revised 2/08
Loading...