American Standard 0630.000 User Manual

BARRIER FREE

31"

(787mm)

SUGGESTED

34"

(864mm)

7-5/8"

(194mm)

15-1/2"

(394mm)

15-1/2"

(394mm)

(203mm)

1-1/4" O.D. TAILPIECE

1-1/4" O.D. WASTE

FINISHED FLOOR

*10-3/4"

(273mm)

*12-7/8"

(327mm)

COUNTERTOP

(BY OTHERS)

SEALING

COMPOUND

5/8"

(16mm)

(152mm)

SUPPLIES AS REQ'D

1-3/4" DIA.

STD. DRAIN

OUTLET

2" (51mm) MINIMUM

2-1/2" (64mm)

EDGE OF

COUNTERTOP

CUTOUT

FINISHED WALL

OR SPLASHBACK

1-1/4" DIA. C.H.

(TYPICAL)

MTG CLIP

(4 PLACES)

CUTOUT

AREA

DET AIL OF MOUN TIN G CLIP

(KI T No.4 7194. 007 0A)

LAVA

BRASS

INSERT

19mm

(3/4) MIN.

REFER TO INSTRUCTIONS

PROVIDED WITH KIT FOR

ADDITIONAL INFORMATION

CLIP MACH. SCREW

FITTING

CENTER-S ET

SPREAD

27mm(1-1 /16)

32mm(1-1 /4)

102mm(4)

203mm(8)

686mm

(27)

MIN.

864mm

(34)

76mm

(3)

610mm

(24)

BARRIER FREE

CLEARANCE

152mm

(6)

MAX.

229mm

(9)

MIN.

203mm

(8)

MIN.

DRAWING FOR

DIMENSIONAL

PURPOSES ONLY.

IT IS NOT AN EXACT

REPRESENTATION.

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 ACCESSIBLE AND USABLE BUILDINGS AND FACILITIES CHECK LOCAL CODES.

Countertop 864mm (34") from finished floor. Lavatory installed 51mm (2") MIN. from front edge of countertop. Countertop thickness to be 25mm (1") maximum.

ORBIT™ UNDERCOUNTER SINK

• Round undermount sink

• Made from vitreous china

• Front overow

• Unglazed rim for undercounter mounting

• Supplied with mounting kit (047194-0070A) and template

❏ 0630.000 Sink less faucet deck

Nominal Dimensions:

394mm dia. (15-1/2") Round

Bowl sizes:

324mm (12-3/4") wide 111mm (4-3/8") deep

Compliance Certications Meets or Exceeds the Following Specications:

• ASME A112.19.2M for Vitreous China Fixtures

• CAN/CSA B45 series

ORBIT™

UNDERCOUNTER SINK

VITREOUS CHINA

To Be Specied:

❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Silver ❏ Fawn Beige ❏ Black

❏ Faucet*: ❏ Faucet Finish: ❏ Supplies: ❏ 1-1/4" Trap:

* See faucet section for additional models available

NOTES:

DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TR AP ARE

SUGGESTED.

▼ UNDERCOUNTER MOUNTING KIT SUPPLIED WITH SINK.

FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. USE ENCLOSED TEMPLATE FOR COUNTERTOP CUTOUT. SEALING COMPOUND SUPPLIED BY OTHERS.

IMPORTANT: Dimensions of xtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

J51

Revised 2/08