American Standard 0625.000 User Manual
BARRIER FREE
GLENDALE™ UNDER COUNTER SINK
• Shell style pattern in bowl
• Made from vitreous china
• Unglazed rim for undermount
• Front over ow with option of rear over ow
installation for Barrier Free
• Center drain outlet
• Supplied with mounting kit (047194-0070A)
and template
❏ 0625.000
464 x 381mm
(18-1/4" x 15")
Bowl Sizes:
406mm (16") wide
311mm (12-1/4") front to back
152mm (6") deep
Compliance Certi cations Meets or Exceeds the
Following Speci cations:
• ASME A112.19.2M for
Vitreous China Fixtures
To Be Speci ed:
❏ Color:
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap:
* See faucet section for additional models available
MEETS THE AMERICAN S WITH D ISABILITIES ACT
GUIDELINES AND ANSI A117.1 ACCESSIBLE AND
USABLE BUILDINGS AND FACILIT IES CHECK LOCAL CODES.
With over ow to the rear and countertop 864mm (34”)
from nished oor. Lavatory installed 51mm (2”) MIN.
from front edge of countertop. Countertop thickness to
be 25mm (1”) maximum.
343mm
*
(13-1/2)
787mm (31)
864mm (34)
51mm
(2) MIN.
76mm
(3)
EDGE OF
COUNTER
TOP
CUTOUT
273mm
*
(10-3/4)
381mm
(15)
25mm
197mm
(7-3/4)
GLENDALE™
UNDERCOUNTER SINK
VITREOUS CHINA
A
(1)
SEALING
COMPOUND
16mm
(5/8)
SUPPLIES
AS REQ'D.
1-1/4 O.D.
WASTE
1-1/4 O.D.
TAILPIECE
FITTING
CENTER-SET
SPREAD
NOTES:
DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
*
SUGGESTED.
▼ UNDERCOUNTER MOUNTING KIT SUPPLIED WITH SINK.
FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED
SEPARATELY.
IN-FIELD ADJUSTMENT OF POP-UP ROD EXTENSION REQUIRED. PROVIDE A
2-1/2" OFF-SET BEND FOR PROPER OPERATION.
USE ENCLOSED TEMPLATE FOR COUNTERTOP CUTOUT.
SEALING COMPOUND SUPPLIED BY OTHERS.
IMPORTANT: Dimensions of xtures are nominal and may vary within the range of
tolerances established by ANSI Standard A112.19.2. These measurements are
subject to change or cancellation. No responsibility is assumed for use of
superseded or voided pages.
45°
464mm
(18-1/4)
19mm
(3/4)
B
C/L
FINISHED FLOOR
A
27mm(1-1/16)
32mm(1-1/4)
OVERFLOW
203mm
(8)
B
102mm(4)
203mm(8)
FINISHED WALL
OR SPLASHBACK
41mm
(1-5/8)
180mm
(7-5/8)
C/L OF
OUTLET
MOUNTING
CLIP
(SEE DETAIL)
COUNTERTOP
(BY OTHERS)
DETAIL OF MOUNTING CLIP
(KIT No.47194.0070A)
BRASS
INSERT
LAVA
REFER TO INSTRUCTIONS
PROVIDED WITH KIT FOR
ADDITIONAL INFORMATION
864mm
(34)
(3/4) MIN.
MACH.
SCREW
686mm
19mm
CLIP
(27)
MIN.
76mm
(3)
203mm
(8)
MIN.
BARRIER FREE
CLEARANCE
610mm
(24)
DRAWING FOR
DIMENSIONAL
PURPOSES ONLY.
IT IS NOT AN EXACT
REPRESENTATION.
152mm
(6)
MAX.
229mm
(9)
MIN.
© 2006 American Standard Inc.
J47
Revised 5/06
Loading...