American Standard 0268.888, 0044.000, 0268.144, 738520-0070A, 3520.000 User Manual
...
RAVENNA™ WALL-HUNG
24-1/4"
(616mm)
9-1/2"
(241mm)
2"
(51mm)
7/8" (22mm) DIA.
SLAB ANCHOR
SCREW HOLES ON
9-1/2" (241mm) CTRS
34"
(864mm)
14-3/8"
(365mm)
5"
(127mm)
19-1/2"
(495mm)
3-1/4"
(83mm)
7-3/4"
(197mm)
1/2" (13mm) DIA.
SEMI-PED ANCHOR
SCREW HOLES ON
4-1/4" (108mm) CTRS
*21"
(533mm)
2-3/4"
(70mm)
1-1/4" O.D.
WASTE
SUPPLIES AS
REQUIRED
1-1/4" O.D.
TAILPIECE
8-1/4"
(210mm)
FINISHED
FLOOR
FINISHED
WALL
20"
(508mm)
4"
(102mm)
1-3/4" DIA.
STD. DRAIN
OUTLET
SEMI-PED
BASE
TOWEL
RAIL
*24-3/4"
(629mm)
SEMI-PEDESTAL LAVATORY
• Vitreous china
• Contemporary design wall-hung with
semi-pedestal P-trap cover for ease of cleaning
• Rear overow
• Soap and accessory deck
• Optional with integral mounted towel bar
(ordered separately)
• Supplied with mounting kit
• Design matched to Ravenna toilets
(faucet shown not included)
• Faucet ledge with generous shelf area
for accessories
❏ 0268.444 Faucet holes on 4" (102mm) centers
(shown)
❏ 0268.888 Faucet holes on 8" (203mm) centers
❏ 0268.144 Center hole only
Nominal Dimensions:
24-1/4" x 19-1/2" x 34"
(616 x 495 x 864mm)
RAVENNA™
SEMI-PEDESTAL SINK
VITREOUS CHINA
Separate Components:
❏ 0268.004 Lavatory slab 4" (102mm) centers
❏ 0268.008 Lavatory slab 8" (203mm) centers
❏ 0268.001 Lavatory slab center hole only
❏ 0044.000 Semi-pedestal leg
Recommended Components:
❏ 3520.000 Integral Towel Bar
002 Chrome, 295 Satin Nickel
❏ 738520-0070A Towel Bar mounting kit
Bowl sizes:
19" (483mm) wide
12" (305mm) front to back
6" (152mm) deep
Compliance Certications:
Meets or exceeds the following specications:
• ASME A112.19.2 for vitreous china xtures
To Be Specied:
❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Black
❏ Faucet*:
❏ Faucet Finish:
❏ Supplies:
❏ 1-1/4" Trap
* See faucet section for additional models available
© 2008 AS America Inc.
NOTES:
* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TR AP ARE
SUGGESTED.
▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.
■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST
BE TAKEN FROM FIXTURE.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
IMPORTANT: Dimensions of xtures are nominal and may vary within the
range of tolerances established by ANSI Standard A112.19.2.
These measurements are subject to c hange or cancellation. No responsibility
is assumed for use of superseded or voided pages.
J60
Revised
Revised 5/06
Loading...