![](/html/2b/2b57/2b571cb57b71663d70c81dcaf396532a0fe8169a2536e4f9a64be470ac8ce50b/bg1.png)
© Copyright 2011, American Fibertek, Inc. 1202TS
Bi-directional Multi-Protocol Data
And Bi-directional Contact Closure
Instruction Manual
Video Transmitter With
MT-915C-SL
![](/html/2b/2b57/2b571cb57b71663d70c81dcaf396532a0fe8169a2536e4f9a64be470ac8ce50b/bg2.png)
INSTALLATION AND OPERATION INSTRUCTIONS
INTRODUCTION
Thank you for purchasing your American Fibertek MT-915C-SL singlemode video transmitter with bidirectional multi-protocol data and bi-directional contact closure. Please take a few minutes to read
these installation instructions in order to obtain the maximum performance from this product.
FUNCTIONAL DESCRIPTION
The MT-915C-SL operates as half of a transmitter / receiver pair for the transmission of high
performance 10 bit digital NTSC, PAL, RS170, or RS343 video signals. The MT-915C-SL also supports
two bi-directional data channels. These data channels are configured as follows:
Channel 1: RS485 (2 or 4 wire) data, RS422 data, RS232 data, or Manchester data
Channel 2: Contact Closure (dry)
NOTE: This unit is shipped with Channel 1 in the RS485 4-wire configuration. For other
configurations, please refer to the DATA CONFIGURATION section for changes to the default
switch settings.
The MT-915C-SL is designed to operate with the MR-915C-SL or RR-915C-SL video receiver with bidirectional data over one multimode fiber optic cable.
The MT-915C-SL multiplexes a single video input signal along with up to two data signals into a high
speed serial data stream. This serial data stream modulates a laser at 1310 nm wavelength. The MT915C-SL also detects and demultiplexes a return optical serial data stream signal containing up to two
data channels at 1550 nm wavelength. The 915C-SL Series product is designed to operate over an
optical loss budget range of 0 to 21 dB when used on 9 um singlemode fiber. Refer to the product
specification sheet for additional performance data.
The RS485 channel may be configured for 2-wire (half duplex) or 4-wire (full duplex) with or without
biasing. Switch selectable internal 120 ohm terminations are available for RS422 or RS485 data.
This unit is contained in a rugged aluminum housing with internal dc voltage regulation. The detachable
terminal blocks and LED indicators provide for easy installation and monitoring of video, data, and
optical power.
The MT-915C-SL is designed for mounting as a modular stand alone unit. For a rack mounted version
please see the RT-915C-SL.
2
![](/html/2b/2b57/2b571cb57b71663d70c81dcaf396532a0fe8169a2536e4f9a64be470ac8ce50b/bg3.png)
INSTALLATION
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD
CONFORM TO THE NATIONAL ELECTRICAL CODE, ANSI/NFPA 70 AND LOCAL CODES.
Mount the unit to a secure surface using #8 (3mm) hardware in four places. See the drawing on the
next page for mounting dimensions. Be sure to allow sufficient room for the required minimum bend
radius of the fiber cable used.
POWER SOURCE
THIS PRODUCT SHALL BE POWERED BY A LISTED CLASS 2 POWER SUPPLY ONLY.
This unit requires a +12VDC power source with a current rating of 1.25 amps for proper operation. The
DC input is diode protected. In the USA and in Canada an American Fibertek PS-12D is supplied with
this unit. The negative side of the power input is directly connected to ground. ANSI/NFPA 70 Class 2
wiring is recommended.
POWER CONNECTION
Power is supplied to the unit via a two pin terminal connector on the right side of the unit. Follow the
label on unit for proper orientation of +12 volt dc and ground.
FIBER CONNECTION
The fiber optic connection is made via a ST connector located on the right side of the unit.
VIDEO INPUT CONNECTION
The video input connection is made via a BNC connector on the right side of the unit. The video input
should be connected to an appropriate 75Ω base band video source such as a camera or a video
recorder output. For optimum performance the video cables should be the shortest length of coax
practical.
3