Page 1
Sixteen Channel Video Multiplexer
© Copyright 2008, American Fibertek, Inc.
Instruction Manual
MRT-91600C
MRR-91600C
0312
JPK
Page 2
Functional Descript
Installation
Power Source
Fiber Connection
Video
MRT-91600C
MRR-91600C
Warranty
..........................................................................................
.....................................................................................
................................................................................
Input / Output Connections
Status LED Indicators
Status LED Indicators
/ Service Information
Table of Contents
ion
........................................................................
......................................................
..................................................
..................................................
...........................................................
3
3
4
4
4
5
6
7
2
Page 3
INSTALLATION AND OPERATION INSTRUCTIONS
INTRODUCTION
Thank you for purchasing your American Fibertek Series
video multiplexer
obtain the maximum performance from this product.
FUNCTIONAL DESCRIPTION
The
91600C
sixteen
The MRT-916
videos and multiplexes each group into a high speed serial data stream. The first group s serial
data stream, modulates a laser at 1310nm wavelength. The second groups serial data stream
modulates a laser at 1550nm. A Wave Division Multiplexer (WDM) combines these two
wavelengths, onto a single optical output port for connection to the fiber transmission
Correspondingly, the MRRvideo output signals. The
budget range of 0dB to 10dB
Refer to the product specification sheet for additional performance data.
The individual units may be configured for rack mounting or wall mounting depending upon the
installation
MRR-9100C
hardware is included, overall width increases to 19 inches wide.
simultaneous NTSC
of the included mounting hardware. Nominal dimensions of the MRT-91600C and
. Please take a few minutes to read these installation instructions in order to
Series units operate as a transmitter / receiver pair for the
or
PAL video signals
00C
transmitter accepts up to sixteen video inputs in two groups containing eight
91600C
916
are 1 ¾ inches high by 17 inches wide by 11 ½ inches deep. When mounting
receiver converts the optical signal to sixteen i
00C
Series product is designed to operate over an optical loss
on 62.5
um
over one multimode fiber optic cable.
multimode
fiber over a maximum distance of 1 Km
91600C multimode sixteen
digital
transmission of
ndependent
channel
system.
.
INSTALLATION
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND
SHOULD CONFORM TO THE NATIONAL ELECTRICAL CODE, ANSI/NFPA 70 AND LOCAL
CODES.
To install the MRT-91600C
unit.
For rack mounting the ears are installed on the
sides of the unit with the surfaces that have
oval holes flush with the front of the unit as in
Figure 1. Mount the ears with the #10 flathead
screws provided. To mount in the rack cabinet,
use mounting screws that are appropriate for
the rack cabinet being used. When mounting
the MRT-91600C or MRRconfiguration, it is recommended that sufficient
airflow is available through the unit. This
be achieved by leaving a 1RU slot above the unit open for air movement and by leaving open
space along the sides of the unit.
or MRR-91600C
91600C
in a rack
it is fir
can
st necessary to mount the rack flanges to the
3
Page 4
For mounting the unit flush to a wall or other rigid
surface, the ears may be installed on the sides
with the oval holes f
as in Figure 2. Mount the ears with the #10
flathead screws provided. Mount the unit to a rigid
surface using #10 (5mm) screws.
POWER SOURCE
The internal power supply accepts universal line voltage. Any mains supply from 100 to 240
VAC, 50 to 60 Hz, may be used without modification or adjustment. A universal power
connector is provided on the rear of the unit to facilitate connection to the power mains.
POWER CONNECTION
A three conductor power line cord is supplied in the US, UK
conductor is directly connected to the chassis.
lush with the bottom of the unit
, and
Europe.
The ground
FIBER
The fiber optic connection is made via a ST connector located at the back of the unit. Be sure to
allow sufficient room for the required minimum bend ra
VIDEO INPUT / OUTPUT CONNECTIONS
Video input and output connections are located on the rear of the unit. A BNC connector is
provided for each channel. The video inputs are connected to an appropriate 75
video source such as a camera or a video recorder output. The 75
looped through typical baseband video inputs of switchers, recorders and other equipment as
required. For proper operation, the outputs must be terminated with 75 . For optimum
performance the video cables should be the shortest length of coax practical.
CONNECTION
dius of the fiber cable used.
video outputs can be
baseband
4
Page 5
MRT-
The MRTinstallation and troubleshooting:
VLI 1 THROUGH VLI 16
A bi-color LED indicator is provided for each of the sixteen video inputs to the MRTVideo status associated with each of these LED s is summarized below.
91600C
Video Presence LED
STATUS INDICATORS
91600C
Green
transmitter provides the following front panel LED status indicators to aid in
Red
V
Proper Input Video Present
Input Video Not Detected
ideo Status
91600C.
5
Page 6
MRR-91600C
The MRRinstallation and troubleshooting:
VLI 1 THROUGH VLI 16
A bi-color LED indicator is provided for the each of the sixteen video
91600C
SYNC
A bi-color LED indicator is provided to monitor the proper serialization of the electrical v
data stream through the MRR-91600C. A SYNC indicator for videos one
above the OLI 1 indicator. A SYNC indicator for videos
t
he OLI 2 indicator.
. Video status associated with each of these LEDs is summarized below.
Video Presence LED
STATUS INDICATORS
91600C
Green
Red
receiver provides the following front panel LED status indicators to aid in
Out
Sync status associated with th
Video Status
Proper
Out
put Video Present
put Video Not Detected
through eight is located
nine
through
ese
LEDs is summarized below.
sixteen
out
puts of the MRR-
is located above
ideo
Sync LED
Green
Red
OLI 1
A bi-color LED indicator monitors the power of the optical input
received at the MRRpower and optical input
Optical Level Indicator
OLI 2
A bi-color LED indicator monitors the power of the optical input signal that is being received at
the MRRoptical input status associated with this LED are summarized below.
Optical Level Indicator
Green
Red
Off
916
00C
Green
Red
Off
Proper Data Stream Serialization Present
Data Stream Serialization Not Detected
91600C
On
from video channels
On
from video channels one through
power
status associated with this LED are summarized below.
AC Power Status
AC Power Status
Sync Status
On
Off
nine
through
On
Off
power
eight
of the MRT-
Proper Optical Input Power Present
Optical Input Not Detected
Check Power Supply Input
sixteen
Proper Optical Input Power Present
Optical In
Check Power Supply Input
Optical Status
of the MRT-
Optical Status
put Not Detected
91600C
signal that is being
91600C
. AC power and
. AC
6
Page 7
LIFETIME WARRANTY INFORMATION
American Fibertek, Inc warrants that at the time of delivery the products delivered will be free of
defects in materials and workmanship. Defective products will be repaired or replaced at the
exclusive option of American Fibertek. A Return Material Authorization (RMA) number is
required to send the products back in case of return. All returns must be shipped prepaid. This
warranty is void if the products have been tampered with. This warranty shall be construed in
accordance with New Jersey law and the courts of New Jersey shall have exclusive jurisdiction
over this contract. EXCEPT FOR THE FOREGOING WARRANTY, THERE IS NO WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE,
EXPRESSED OR IMPLIED, WHICH EXTENDS BEYOND THE WARRANTY SET FORTH IN
THIS AGREEMENT. In any event, American Fibertek will not be responsible or liable for
contingent, consequential, or incidental damages. No agreement or understanding, expressed
or implied, except as set forth in this warranty, will be binding upon American Fibertek unless in
writing, signed by a duly authorized officer of American Fibertek.
SERVICE INFORMATION
There are no user serv
In the event that service is required to this unit, please direct all inquiries to:
American Fibertek, Inc.
120 Belmont Drive
Somerset, NJ 08873
iceable parts inside the unit.
E-
mail:
techinfo@americanfibertek.com
Phone: (877) 234-7200
Phone: (732) 302-0660
FAX (732) 302-0667
7
Loading...