American Dynamics ROENDC Specsheet

ROENDC End Cap

A

For SpeedDome® Ultra or SpeedDome®
Optima Indoor/Outdoor Housing

Installation Guide

Regulatory Compliance: Safety UL1950

2. Slip the cable into the hole of the rubber dust
plug and work the plug into the pipe opening.
When done, the plug must be fully inserted and
must fully seal the opening.

3. IMPORTANT! Thread two setscrews provided
into the adapter pipe. Also, to prevent water
intrusion, ensure the adapter pipe has the
gasket and rubber seal preinstalled.

Gasket (seat in groove
at bottom of opening)

The ROENDC end cap enables the indoor/outdoor
housing of a SpeedDome Ultra or Optima camera
dome to be attached to an existing 3.8cm (1-1/2in)
diameter pipe.

Parts Supplied

End Cap Assembly 1 0101-0051-01
Install Kit, 0351-2143-01

Setscrew 2 2821-0010-01
Allen Wrench 1 1400-0112-06
Wrench, Torx, Tamperproof 1 1400-0149-01
Plug, Foam 1 0505-0296-01

4. Run cables from the existing pipe through the

Procedure

1. Remove pipe elbows (if any), and then make a
mark 4cm (1.6in) from the end of the existing
pipe.

4cm (1.6in)

Rubber Seal (seat
over opening)

Setscrew (2)

end cap and out its front. Install the end cap as
follows:

a. Align arrow on the adapter pipe with the

mark at the top of the pipe assembly.

b. Maintaining arrow/line alignment, insert the

dome/adapter pipe assembly onto the pipe
until the rubber sleeve on the adapter pipe
meets the circumference mark.

c. Maintaining compression, tighten the two

setscrews using the Allen wrench.

Note: If marks on the pipe of the mounting
structure are missing, scribe a circumference
mark 4cm (1.57in) from the end of the pipe.

B

C

Side

Top

© 2005 Sensormatic® Electronics Corp.

ROENDC END CAP 8000-2692-04, REV. F
INSTALLATION GUIDE

1 of 2

Top

A

A

t

5. Check the level of the pipe assembly. If re­leveling is necessary, loosen the two set
screws and repeat step 4.

6. Apply Teflon tape to the threads at the top of
the housing. Then A) route the cable from the
housing through the bottom opening of the end
cap and out the its front, and B) twirling the
cables to relieve tension, screw the housing
onto the adapter pipe. Keep turning the
housing until tight.

pply Teflon tape
to threads at the
top of the h

ousing.

B

7. Re-check the level of the dome in the two
directions shown. Re-level if necessary.

8. Connect cables, stuff excess cable into the end
cap, and ensure the O-ring is in place. Then,
using a wrench for tamperproof screws, attach
the cover to the end cap.

Note: For cable connections, see the
instruction card supplied with the dome.

Declarations

Thank you for using American Dynamics products. We
support our products through an extensive and worldwide
network of dealers. The dealer, through whom you originally
purchased this product, is your point of contact if you have a
need for service or support. Our dealers are fully empowered
to provide the very best in customer service and support.
Dealers should contact American Dynamics at
[phone] or [phone] or on the web at
www.americandynamics.net.

WARRANTY DISCLAIMER: Sensormatic Electronics
Corporation makes no representation or warranty with respect
to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular
purpose.

NOTICE: The information in this manual was current when
published. The manufacturer reserves the right to revise and
improve its products. All specifications are therefore subject to
change without notice.

LIMITED RIGHTS NOTICE: For units of the Department
of Defense, all documentation and manuals were developed at
private expense and no part of it was developed using
Government Funds. The restrictions governing the use and
disclosure of technical data marked with this legend are set
forth in the definition of “limited rights” in paragraph (a) (15)
of the clause of DFARS 252.227.7013. Unpublished - rights
reserved under the Copyright Laws of the United States.

TRADEMARK NOTICE: American Dynamics and
Sensormatic are trademarks or registered trademarks of

Sensormatic Electronics Corporation. Other product names
mentioned herein may be trademarks or registered trademarks
of Sensormatic or other companies.

COPYRIGHT: Under copyright laws, the contents of this
manual may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machine­readable form, in whole or in part, without prior written
consent of Sensormatic Electronics.

RLJ 3/05

O-ring

www.americandynamics.ne

ROENDC END CAP 8000-2692-04, REV. F
INSTALLATION GUIDE

2 of 2