American Dynamics RHOWPA User Manual

2. Prepare the bands for mounting.

A

A

RHOWPA Pole Mount

For SpeedDome® Ultra or SpeedDome®
Optima Outdoor Housings

Installation Guide

A. Remove the band from the clamp package and

cut two bands appropriate for the diameter of
the pole. Slip each band through the upper and
lower slots in the bracket.

B. Bend the right side of each band inward and

slip the bend through the large slot in the screw
assembly. Flatten the bend tight with fingers.

Regulatory Compliance: Safety UL1950

OR

3. Place bracket against the pole. Then wrap one of
the band assemblies around the pole so the screws
are opposite the bracket.

A. Cut the band to length 2.54cm (1in) beyond the

B. Using your fingers, flatten the last 2.54cm (1in)

Parts Supplied

Bracket 1 0500-9631-01
Install Kit 0351-2122-01

Clamp Package 2 6010-0043-01
Nut, Locking, M6 4 5826-0500-020
Washer, Large, M6 4 5842-0500-020

C. Repeat for the remaining band assembly.

. B. C.

. B.

first notch in the band.

of the band inward to form a hook. Insert the
hook through the remaining slot in the rack and
turn the screw to secure the bracket to the pole.

Cut

Tools Required

Rear of
bracket

Bend

Rear of
bracket

Bend

· Socket Wrench Kit w/Extension (metric)

· Screwdriver

· Pliers

· Scissors or metal shears

Procedure

1. With words “this side up” etched in rack facing up,
insert rack into screw assembly. Then turn screw
just enough to engage rack. Prepare two racks this
way.

Rack

© 2004 Sensormatic

Screw Assy.

4. Attach mounting structure to the pole bracket
according to instructions supplied with the
mounting structure.

RHOWPA POLE MOUNT 8000-2692-11, REV. C
INSTALLATION GUIDE

1 of 2

Declarations

t

Thank you for using American Dynamics products. We
support our products through an extensive and worldwide
network of dealers. The dealer, through whom you originally
purchased this product, is your point of contact if you have a
need for service or support. Our dealers are fully empowered
to provide the very best in customer service and support.
Dealers should contact American Dynamics at
[phone] or [phone] or on the web at
www.americandynamics.net.

WARRANTY DISCLAIMER: Sensormatic Electronics
Corporation makes no representation or warranty with respect
to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular
purpose.

NOTICE: The information in this manual was current when
published. The manufacturer reserves the right to revise and
improve its products. All specifications are therefore subject to
change without notice.

LIMITED RIGHTS NOTICE: For units of the Department
of Defense, all documentation and manuals were developed at
private expense and no part of it was developed using
Government Funds. The restrictions governing the use and
disclosure of technical data marked with this legend are set
forth in the definition of “limited rights” in paragraph (a) (15)
of the clause of DFARS 252.227.7013. Unpublished - rights
reserved under the Copyright Laws of the United States.

TRADEMARK NOTICE: American Dynamics and
Sensormatic are trademarks or registered trademarks of

Sensormatic Electronics Corporation. Other product names
mentioned herein may be trademarks or registered trademarks
of Sensormatic or other companies.

COPYRIGHT: Under copyright laws, the contents of this
manual may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machine­readable form, in whole or in part, without prior written
consent of Sensormatic Electronics.

MDR 1/04

www.americandynamics.ne

RHOWPA POLE MOUNT 8000-2692-11, REV. C
INSTALLATION GUIDE

2 of 2