RHOTR
Over-the-Roof Mount
For SpeedDome® Ultra or SpeedDome®
Optima Outdoor Housing
Installation Guide
Regulatory Compliance: Safety UL1950
Parts Supplied
Pipe, Outdoor Arm 1 0500-3635-02
Bracket, Hinge 2 0500-9403-01
Adapter Pipe Assembly 1 0101-0051-01
Install Kit 0351-2118-01
Anchor, M6, Wedge w/Hardware 4 2880-0108-01
Washer, Locking, M6 4 5846-0500-020
Washer, Flat Large 4 5842-0500-020
Plug, Foam 1 0505-0296-01
Wrench, Allen 1 1400-0112-06
Wrench, Tamperproof, Torx 1 1400-0149-01
Tools Required
· Teflon Tape
· Level
· Power Drill
· Hammer
· Pliers
· Socket Wrench Kit w/Extension (metric)
Procedure
Note: Brackets for the arm that holds the dome
can be positioned against a wall or in a corner as
shown in these instructions.
1. Insert pipe through both support brackets as
shown. Then position the pipe and brackets as
desired so the brackets are properly spaced.
The wider apart the brackets, the more stable
the pipe will be. Mark holes for anchors.
473mm (18.6in)
394mm (15.5in)
)
n
i
3
4
(
m
m
8
9
0
1
100mm (3.9in)
© 2004 Sensormatic
RHOTR OVER-THE-ROOF MOUNT 8000-2692-06, REV. E
INSTALLATION GUIDE
1 of 4
2. Drill holes and install anchors as shown below.
Extend anchor threads
as shown.
15mm (0.6in)
Thread two nuts
back-to-back to
protect the anchor
when hammering it
into wall.
3. On the lower bracket, bend the tab (pipe stop)
inward and bolt both brackets to the wall using
the nuts and washers provided.
5. Slip the cable into the hole of the rubber dust
plug and work the plug into the pipe opening.
When done, the plug must be fully inserted and
must fully seal the opening.
6. IMPORTANT! To prevent water intrusion,
ensure the adapter pipe has a gasket and
sleeve preinstalled.
Gasket (seat in groove
at bottom of opening)
Rubber Seal (seat
over opening)
4. Reinsert the pipe through the brackets and
route the conduit and cable up through the
pipe. Insert at least 15.2cm (6in) of conduit into
the pipe. Turn the top of the arm inward to
facilitate assembly.
RHOTR OVER-THE-ROOF MOUNT 8000-2692-06, REV. E
INSTALLATION GUIDE
2 of 4
7. Run cables from the existing pipe through the
adapter pipe and out its front. Reinstall the
adapter pipe as follows:
A. Align arrow on the adapter pipe with the
mark at the top of the pipe assembly.
B. Maintaining arrow/line alignment, insert the
dome/adapter pipe assembly onto the pipe
until the rubber sleeve on the adapter pipe
meets the circumference mark.
C. Maintaining compression, tighten the two
setscrews using the Allen wrench.
Note: If marks on the pipe of the mounting
structure are missing, scribe a circumference
mark 4cm (1.57in) from the end of the pipe.
A B C
Side
Top
Top
10. Re-check the level of the dome in the two
directions shown. Re-level if necessary.
11. Connect cables, stuff excess cable into the
adapter pipe, and ensure the O-ring is in place.
Then, using a wrench for tamperproof screws,
attach the end cap.
Note: For cable connections, see the
instruction card supplied with the dome.
O-ring
12. Swing the dome to the desired position over
the roof and tighten the setscrews.
8. Check the level of the pipe assembly. If releveling is necessary, loosen the two set
screws and repeat steps 8.
9. Apply Teflon tape to the threads at the top of
the housing. Then A) route the cable from the
housing through the bottom opening of the
adapter pipe and out its front, and B) twirling
the cables to relieve tension, screw the
housing onto the adapter pipe. Keep turning
the housing until tight.
Apply Teflon tape to threads
at the top of the housing.
A
Set screws (2)
(wrench supplied)
RHOTR OVER-THE-ROOF MOUNT 8000-2692-06, REV. E
INSTALLATION GUIDE
B
3 of 4
Declarations
t
Thank you for using American Dynamics products. We
support our products through an extensive and worldwide
network of dealers. The dealer, through whom you originally
purchased this product, is your point of contact if you have a
need for service or support. Our dealers are fully empowered
to provide the very best in customer service and support.
Dealers should contact American Dynamics at
(800) 507-6268 or (561) 912-6259 or on the web at
www.americandynamics.net.
WARRANTY DISCLAIMER: Sensormatic Electronics
Corporation makes no representation or warranty with respect
to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular
purpose.
NOTICE: The information in this manual was current when
published. The manufacturer reserves the right to revise and
improve its products. All specifications are therefore subject to
change without notice.
LIMITED RIGHTS NOTICE: For units of the Department
of Defense, all documentation and manuals were developed at
private expense and no part of it was developed using
Government Funds. The restrictions governing the use and
disclosure of technical data marked with this legend are set
forth in the definition of “limited rights” in paragraph (a) (15)
of the clause of DFARS 252.227.7013. Unpublished - rights
reserved under the Copyright Laws of the United States.
TRADEMARK NOTICE: American Dynamics and
Sensormatic are trademarks or registered trademarks of
Sensormatic Electronics Corporation. Other product names
mentioned herein may be trademarks or registered trademarks
of Sensormatic or other companies.
COPYRIGHT: Under copyright laws, the contents of this
manual may not be copied, photocopied, reproduced,
translated or reduced to any electronic medium or machinereadable form, in whole or in part, without prior written
consent of Sensormatic Electronics.
MDR 1/04
www.americandynamics.ne
RHOTR OVER-THE-ROOF MOUNT 8000-2692-06, REV. E
INSTALLATION GUIDE
4 of 4
Loading...