American Dynamics RHIU3X3, RHIU4X4, RHIUAB, RHIUFB, RHIUHC Specsheet

...

FEATURES

Complete line of indoor

•

and outdoor mounts to suit any mounting requirement

Compatible with

•

SpeedDome Ultra, SpeedDome Ultra Drone, and SpeedDome Optima Series of programmable domes

Lightweight, aesthetic

•

design Meets IP66/NEMA 4

•

(outdoor mounts) and IP40 (indoor mounts) standards

Tamper-resistant

•

Corrosion-resistant,

•

waterproof design Choose from different

•

varieties of ceiling, wall, pendant, corner, pole, and over-the-roof mounts

Ground-level assembly of

•

dome/housing/end cap for quick, safe and efficient installations

Dome Mounts

American Dynamics’ family of programmable domes is complimented by a comprehensive line of mounts to accommodate any indoor or outdoor mounting requirement. These mounts

are compatible with the SpeedDome Series, and the SpeedDome Optima Series of programmable domes.

Choose from a variety of wall mounts, corner mounts, pole mounts, ceiling mounts, pendant mounts and over-the-roof mounts for both indoor and outdoor applications. Depending upon the requirements of the application, indoor mounts can be used with or without an optional bubble. The mounts’ innovative end cap and pendant cap design enable the mount and housing to be assembled on the ground, allowing for a safe, quick and efficient installation.

Ultra

www.americandynamics.net

RHIUTH

op Hat Housing with

Trim Ring

RHIUIB

I-Beam Clamp

RHIUHC

Hard Ceiling Bracket

RHIUFB

Fixed Bracket

RHIUAB

Adjustable Bracket

RHIU2X2M

2’ x 2’ Tile Mount

RHIU2X2P

2’ x 2’ Tile Pendant

Mount

RH2X2

2’ x 2’ Tile Mount Plate

RHIUIBM

I-Beam Mount Assembly

This Top Hat housing with trim ring and plastic base mounts directly to a ceiling or to an indoor mounting structure. It is a metal enclosure that houses the dome. The trim ring is slightly larger so that it completely covers the Top Hat’s met

al rim. The RHIUTH is plenum rated.

This bracket enables the Top Hat housing to be recessed in the ceiling (requires RHIUTH Top Hat). The bracket is mounted to the Top Hat and installed in a hole cut in the ceiling - perfect for sheet rock, plaster or solid ceilings. The hard ceiling bracket can be installed entirely from below the ceiling; the installer will not have to access the area above the ceiling to install it.

This bracket enables the Top Hat housing to be recessed in the ceiling or in a 2-foot drop ceiling tile (requires RHIUTH Top Hat). The bracket is mounted to the Top Hat housing and installed in a hole cut in the ceiling. The bracket distributes the weight of the dome and Top Hat housing across the T-bar framework of the ceiling. It is also very useful for sheet rock, plaster, or solid ceilings.

This bracket enables the Top Hat housing to be recessed in drop ceiling that utilize other than 2-foot grids (requires RHIUTH Top Hat). The bracket distributes the weight of the dome and the Top Hat housing across the T-bar framework of the ceiling, and is adjustable from 632-1219 mm (24-48 in).

This mount enables the Top Hat housing to be recessed in a 2’ x 2’ drop tile ceiling. The ceiling tile is removed and the white tile mount is simply dropped in its place. A Top Hat housing and plastic base are included in the kit.

This mount enables the pendant mount to be installed in a 2’ x 2’ drop tile ceiling. The Top Hat housing/dome assembly also mounts to the structure. The mounting kit includes a 2x2 plate and pendant hardware. The plate attaches to a 1.25” pipe, provided by the customer, then affixes to the Top Hat housing/dome assembly. If mounting a SpeedDome Optima with this model, a RHOPN ceiling pendant mount kit is required.

This mount enables the dome to be recessed in a 2’ x 2’ drop tile ceiling. The ceiling tile is removed and the tile mount is simply dropped in its place.

This assembly enables the dome to suspend from an I-beam; it includes the clamp, pipe tee, nipple, and flange. The clamp attaches to a 1.25” pipe, provided by the customer, then affixes to the pendant hardware. The Top Hat housing/dome assembly also mounts to the structure.

SpeedDome Ultra Series SpeedDome Optima

157 x 175 x 175 mm

(6 x 7 x 7 in)

6.7 x 293 x 127 mm (.29 x 12 x 5 in)

212 x 179 x 56 mm

(8 x 7 x 2 in)

180 x 632 x 100 mm

(7 x 24 x 4 in)

180 x 1219 x 100 mm

(7 x 48 x 4 in)

190 x 607 x 607 mm

(7 x 24 x 24 in)

47 x 605 x 605 mm

(2 x 23 x 23 in)

47 x 605 x 605 mm

(2 x 23 x 23 in)

6 m (max.) x 293 x

127 mm

(20 ft (max.) x 12 x

5 in)

Galvanized steel

Steel

Galvanized steel

Aluminum, cold rolled steel, ABS

plastic

Aluminum, cold rolled steel, ABS

plastic

Painted 

aluminum

Steel and

galvanized

steel

2.9 kg

(6.4 lbs)

This clamp enables the dome to suspend from an I-beam. The I-beam clamp is installed in combination with the RHOPN Ceiling Pendant Mount to affix the Top Hat housing/dome assembly in I-beam installations. This clamp is also included with each RHIUIBM.

.77 kg

(1.7 lbs)

1.5 kg

(3.3 lbs)

.70 kg

(1.6 lbs)

1.8 kg

(4.0 lbs)

2.3 kg

(5.0 lbs)

2.7 kg

(6.0 lbs)

5.4 kg

(12.0 lbs)

1.7 kg

(3.8 lbs)

Product

Description

*Dome

Weight

Dimensions

Construction

Safety

Compatibility

(HxWxD)

This mount allows an outdoor dome housing to be suspended from an outdoor ceiling or horizontal surface. It can be installed using either 1.25'' NPT threaded pipe or rigid conduit, either new or existing, up to 3 meters  (10 feet) in length.

SpeedDome Ultra Series

SpeedDome Optima

1.8 kg

(4.0 lbs)

115 x 120 x 120 mm

(4.5 x 5 x 5 in)

Powder coated

aluminum and 

ABS plastic

RHOPN

Indoor Pendant Mount

Indoor Mounting Options

+ 2 hidden pages