American Dynamics RAS915LS-1, RAS916LS, RAS915LS, RAS916WLS-1, RAS916WLS User Manual
...
SpeedDome Ultra VII
22x Camera Dome
RAS915LS
RAS915LS-1
RAS916LS
RAS916LS-1
RAS916WLS
RAS916WLS-1
Configuration Utility Operator’s Manual
8200-0184-02 D
SpeedDome® Ultra VII
22x Camera Dome
Configuration Utility Operator’s Manual
Version – 0710-0147-0107
EQUIPMENT MODIFICATION CAUTION
Equipment changes or modifications not expressly approved by Sensormatic Electronics Corporation, the party
responsible for FCC compliance, could void the user's authority to operate the equipment and could create a
hazardous condition.
FCC COMPLIANCE
This equipment has been tested and complies with the limits for a Class A digital device, according to Part 15 of the
FCC Rules. These limits provide reasonable protection against harmful interference when the equipment operates in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and, if not
installed and used according to these instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference. If this equipment is used in a
residential area, users must correct the interference at their own expense.
LIMITED RIGHTS NOTICE
For units of the Department of Defense, all documentation and manuals were developed at private expense and no
part of it was developed using Government Funds. The restrictions governing the use and disclosure of technical data
marked with this legend are set forth in the definition of "limited rights" in paragraph (a) (15) of the clause of DFARS
252.227.7013. Unpublished - rights reserved under the Copyright Laws of the United States.
SOFTWARE LICENSE AGREEMENT
A Software License Agreement appears in Appendix S of this manual. Please read it carefully. Using the SpeedDome
Ultra VII Camera Dome Configuration Utility software indicates that you accept the terms and conditions of this
agreement.
NOTICE
The information in this manual was current when published. The manufacturer reserves the right to revise and
improve its products. All specifications are therefore subject to change without notice.
© Copyright 2003 Sensormatic Electronics Corporation
Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced
to any electronic medium or machine-readable form, in whole or in part, without prior written consent of Sensormatic
Electronics.
American Dynamics and SpeedDome are trademarks or registered trademarks of Sensormatic Electronics Corporation.
Product names mentioned herein may be trademarks or registered trademarks of other companies.
Thank you for using American Dynamics products. We support our products through an extensive and worldwide
network of dealers. The dealer, through whom you originally purchased this product, is your point of contact if you
have a need for service or support. Our dealers are fully empowered to provide the very best in customer service and
support. Dealers should contact American Dynamics at (800) 507-6268 or (561) 912-6259, or on the web at
www.americandynamics.net.
02/2004 - BSL
PN-8200-0184-02, Rev. D
TABLE OF CONTENTS
PREFACE: BEFORE YOU BEGIN...................................................................................................................................... V
What’s In This Manual? ................................................................................................................................................... vi
Text Conventions............................................................................................................................................................ vii
Related Documents ........................................................................................................................................................ vii
Getting Help.................................................................................................................................................................... vii
CHAPTER 1: USING THE DOME CONFIGURATION UTILITY.......................................................................................1–1
What is the Dome Configuration Utility? .......................................................................................................................1–2
Starting the Dome Configuration Utility.........................................................................................................................1–2
Working with the Dome Configuration Utility.................................................................................................................1–3
Entering the Dome's Password.....................................................................................................................................1–3
Restoring Factory Settings............................................................................................................................................1–4
Exiting the Configuration Utility.....................................................................................................................................1–5
Accessing the Quick Set Menu.....................................................................................................................................1–5
Where To Go Next........................................................................................................................................................1–7
Keeping Records for the Dome's Settings ....................................................................................................................1–8
CHAPTER 2: CONFIGURING PAN, TILT, ZOOM, AND SYNCHRONIZATION OPTIONS.............................................2–1
Overview of Pan / Tilt / Zoom/Synchronization Options Screen....................................................................................2–2
Setting the Automatic “Flip” Feature .............................................................................................................................2–2
Adjusting the Zoom Stop Settings.................................................................................................................................2–3
Configuring the Line Lock Setting.................................................................................................................................2–4
Configuring the Freeze Frame Setting..........................................................................................................................2–5
Configuring Auto Iris/Auto Focus Resume Settings......................................................................................................2–6
What To Do Next ..........................................................................................................................................................2–7
CHAPTER 3: CONFIGURING CAMERA FEATURES .....................................................................................................3–1
Overview of Camera Settings .......................................................................................................................................3–1
Adjusting White Balance Settings.................................................................................................................................3–2
Working with AGC and Open Shutter Settings..............................................................................................................3–3
What To Do Next ..........................................................................................................................................................3–6
CHAPTER 4: CONFIGURING ALARMS, AREAS, HOME, PRIVACY SETTINGS, PRESETS AND SCAN LIMITS.......4–1
Overview of Alarms, Areas, Home, North Position, Preset, Privacy, and Scan Limit Settings......................................4–2
Configuring Alarm Actions.............................................................................................................................................4–3
Configuring Normal Input States for Alarms..................................................................................................................4–5
Assigning the Dome’s Home Position...........................................................................................................................4–6
Setting the North Position .............................................................................................................................................4–8
Programming Area Boundaries.....................................................................................................................................4–9
Establishing Privacy Zones.........................................................................................................................................4–11
Programming Presets .................................................................................................................................................4–16
Establishing Scan Limits.............................................................................................................................................4–17
What To Do Next ........................................................................................................................................................4–20
CHAPTER 5: CONFIGURING TEXT DISPLAYED ON-SCREEN ....................................................................................5–1
Overview of On-Screen Text Display Settings..............................................................................................................5–1
Displaying or Hiding Status Information........................................................................................................................5–2
Displaying or Hiding All Name Information....................................................................................................................5–3
Displaying Diagnostic Tests During Reset....................................................................................................................5–4
Displaying Direction Indicators......................................................................................................................................5–5
Configuring the Display of Name Information................................................................................................................5–6
Assigning or Changing Name Information.....................................................................................................................5–7
Changing the Settings for Text Displayed On-Screen...................................................................................................5–9
What To Do Next ........................................................................................................................................................5–11
CHAPTER 6: CONFIGURING LANGUAGE AND PASSWORD SETTINGS....................................................................6-1
Overview of Language and Password Settings..............................................................................................................6-1
Selecting a Language for Dome Messages and Prompts..............................................................................................6-2
Setting and Enabling the Dome Password.....................................................................................................................6-3
What To Do Next ...........................................................................................................................................................6-4
CHAPTER 7: DISPLAYING DOME INFORMATION.........................................................................................................7-1
Understanding the Dome Information Screen................................................................................................................7-1
Viewing Dome Operating Statistics................................................................................................................................7-2
What To Do Next ...........................................................................................................................................................7-3
APPENDIX A: SENSORNET AND RS-422 PROTOCOLS COMMAND SUMMARY...................................................... A–1
Command Summary.................................................................................................................................................... A–2
Supported Controllers and Matrix Switching Systems.................................................................................................. A–3
Performance Notes......................................................................................................................................................A–6
APPENDIX B: MANCHESTER PROTOCOL COMMAND SUMMARY...........................................................................B–1
Command Summary.................................................................................................................................................... B–2
Supported Controllers..................................................................................................................................................B–4
Performance Notes......................................................................................................................................................B–4
APPENDIX C: PELCO COAXITRON AND “P” PROTOCOLS COMMAND SUMMARY................................................ C–1
Supported SpeedDome Ultra VII Features...................................................................................................................C–2
Pelco Command Summary ..........................................................................................................................................C–3
Performance Notes......................................................................................................................................................C–4
Tested Pelco Equipment..............................................................................................................................................C–4
Supported Pelco Features ...........................................................................................................................................C–4
APPENDIX D: PANASONIC UP-THE-COAX (UTC) PROTOCOL COMMAND SUMMARY...........................................D–1
Supported SpeedDome Ultra VII Features...................................................................................................................D–2
Panasonic UTC Command Summary..........................................................................................................................D–3
Performance Notes......................................................................................................................................................D–4
Programming Presets ..................................................................................................................................................D–4
Tested Panasonic Equipment ......................................................................................................................................D–5
APPENDIX E: AD UP-THE-COAX (UTC) PROTOCOL COMMAND SUMMARY........................................................... E–1
Command Summary.................................................................................................................................................... E–2
Supported Keyboards .................................................................................................................................................. E–4
Performance Notes......................................................................................................................................................E–4
APPENDIX F: VICON COMMAND SUMMARY................................................................................................................F–1
Supported SpeedDome Ultra VII Features....................................................................................................................F–1
Vicon Command Summary ...........................................................................................................................................F–2
Operating the Dome Configuration Menu......................................................................................................................F–3
Setting Left and Right Auto Pan Scan Limits ................................................................................................................F–4
Wiring Configurations....................................................................................................................................................F–5
Tested Vicon Equipment...............................................................................................................................................F–6
APPENDIX R: DOME CONFIGURATION RECORDS.....................................................................................................R–1
Configuration Settings..................................................................................................................................................R–2
Pan / Tilt / Zoom / Sync Options .............................................................................................................R–2
Camera Functions...................................................................................................................................R–2
Set Alarm Actions....................................................................................................................................R–2
Set Alarm States .....................................................................................................................................R–2
Set Home Position...................................................................................................................................R–2
Set North Position ...................................................................................................................................R–2
Area Boundaries......................................................................................................................................R–3
Privacy Zones..........................................................................................................................................R–3
Scan Limits..............................................................................................................................................R–3
On-Screen Text Display..........................................................................................................................R–3
Text Attribute Options..............................................................................................................................R–3
Language Password................................................................................................................................R–4
Name Configuration ................................................................................................................................R–4
Dome Information....................................................................................................................................R–4
Presets ....................................................................................................................................................R–5
APPENDIX S: SOFTWARE LICENSE AGREEMENT..................................................................................................... S–1
SPEEDDOME ULTRA VII GLOSSARY
INDEX
iv SpeedDome Ultra VII Operator's Manual
PREFACE
Before You Begin
This preface provides important information that you should be familiar with before using the
SpeedDome Ultra VII camera dome. It includes a document overview, text conventions, a list of
related documents, and how to obtain product help.
In This Preface
• What’s In This Manual?..................................................................................................vi
• Text Conventions...........................................................................................................vii
• Related Documents ........................................................................................................vii
• Getting Help...................................................................................................................vii
v
What’s In This Manual?
The SpeedDome Ultra VII Configuration Utility Operator's Manual is organized as follows:
• Chapter 1:Using the Dome Configuration Utility, describes how to use the SpeedDome Ultra VII
Camera Dome configuration utility.
• Chapter 2: Configuring Pan, Tilt, Zoom, and Synchronization Options, describes how to set the
“flip” feature, zoom stop, line lock, Freeze Frame and resuming auto iris/auto focus mode settings.
• Chapter 3: Configuring Camera Features, describes how to configure camera settings to improve
color and low-light performance.
• Chapter 4: Configuring Alarms, Areas, Home, Privacy Settings, Presets and Scan Limits,
describes how to configure settings associated with alarm inputs, the home position, and the North
setting. In addition, you can also set the boundaries for up to 16 areas, establish left and right scan
limits, as well as program presets and Privacy Zones.
• Chapter 5: Configuring Text Displayed On-Screen, describes how to configure settings
associated with displaying text on-screen. This includes names and status information, as well as
the text format and direction indicators.
• Chapter 6: Configuring Language and Password Settings, describes how to set the language for
the menus and prompts. It also describes how to set and enable a password to prevent unauthorized
use of the configuration utility.
IMPORTANT
If Portuguese is the selected language, the characters “ã” and “õ ” are not available for
display on-screen. This is due to a limitation of the dome’s text overlay chip.
• Chapter 7: Displaying Dome Information, explains how to display essential information about
your dome if service should be required.
• Appendix A: SensorNet and RS-422 Protocols Command Summary, provides information about
commands specific to using the dome in a SensorNet or RS-422 environment.
• Appendix B: Manchester Command Protocol Summary, provides information about commands
specific to using the dome in a Manchester environment.
• Appendix C: Pelco Coaxitron and “P” Protocols Command Summary, provides information
about features and commands supported by Pelco Coaxitron and “P” protocols.
• Appendix D: Panasonic Up-the-Coax (UTC) Protocol Command Summary, provides
information about features and commands supported by Panasonic UTC protocol.
• provides information about
Appendix E: AD Up-the-Coax (UTC) Protocol Command Summary,
features and commands supported by AD UTC protocol.
• Appendix F: Vicon Protocol Command Summary, provides information about features and
commands supported by Vicon protocol.
• Appendix R: Dome Configuration Records, provides a convenient place for listing the
configuration information associated with your camera dome.
• ons for using this product.
Appendix S: Software License Agreement, lists the terms and conditi
vi SpeedDome Ultra VII Operator's Manual
Text Conventions
This book uses text in different ways to identify different kinds of information.
Bold Italics
Italics
Bold
Used for terms specific to the system, and text that requires special
emphasis, for example Preset.
Used for menu selections or settings, for example, On-screen Text
Display.
Used for names of buttons, for example, Zoom.
Notes are separated by ruled lines. Notes call attention to any items that may be of
special importance. Icons identify the type of note.
General information
Tips for using the product more effectively
Important information essential to proper operation of the product
Related Documents
Other sources provide supplemental information about your SpeedDome Ultra VII Camera Dome.
These sources serve to enhance your understanding of the product and its use.
• The SpeedDome Ultra VII Camera Dome Configuration Utility Quick Reference Guide
(8200-0184-03) provides a brief overview of how to use the configuration utility.
• The SpeedDome Ultra VII Camera Dome Installation and Service Guide
(8200-0184-01) provides specific information about the wiring and physical set up of the camera
dome.
Getting Help
If you have a question about the operation of this product and cannot find the answer in this manual,
consult with your supervisor. If your supervisor cannot answer your question, contact your Sales
Representative.
Preface vii
NOTES:
viii SpeedDome Ultra VII Operator's Manual
CHAPTER 1
Using the Dome Configuration Utility
The SpeedDome Ultra VII 22x camera dome is an optical zoom camera enclosed in a compact dome
housing. The camera dome supports advanced features such as 11X digital zoom (up to 242X total
zoom), open shutter settings, privacy zones, and direction indicators. The Dome Configuration Utility
is used to customize the camera dome's settings.
This chapter introduces you to the Dome Configuration Utility. It explains how to start the utility,
navigate through the menus, and change settings. It also explains where to find specific information
about customizing dome settings.
In This Chapter
• What is the Dome Configuration Utility?....................................................................1–2
• Starting the Dome Configuration Utility......................................................................1–2
• Working with the Dome Configuration Utility............................................................1–3
• Entering the Dome's Password.....................................................................................1–3
• Restoring Factory Settings...........................................................................................1–4
• Exiting the Configuration Utility.................................................................................1–5
• Accessing the Quick Set Menu....................................................................................1–5
• Where To Go Next ......................................................................................................1–7
• Keeping Records for the Dome's Settings ...................................................................1–8
What is the Dome Configuration Utility?
The Dome Configuration Utility provides a means to setting features for your camera dome via a text
overlay menu. You access this utility using a keystroke combination on your camera controller. The
utility provides settings relating to camera functions, alarms, text display, privacy zones, direction
indicators and password protection. Some items supplement similar features that may be available
through your controller.
Refer to your controller
operating instructions for information about button locations mentioned in
this document.
Starting the Dome Configuration Utility
The Dome Configuration Utility is started using a series of keyboard commands. Depending on the
controller and network protocol in use, the commands required to start the configuration utility differ.
• If the dome is installed in a SensorNet or RS-422 environment, press and hold Iris Open, press
and hold a Focus button (near or far), then press Zoom Out.
• If the dome is installed in a Manchester environment, place the controller in programming mode
(turn the keyswitch to Prog or disable the lock), enter 66, then press Set Preset (Set Shot).
Note: Other protocols and controllers may be supported. The Appendixes located at
the end of this manual provide additional information.
The following menu appears on the monitor:
DOME CONFIGURATION MENU
PAN/TILT/ZOOM/SYNC OPTS
CAMERA FUNCTIONS
ALARMS/AREAS/PRESETS/PZ
ON-SCREEN TEXT DISPLAY
LANGUAGE / PASSWORD
DOME INFORMATION
RESET TO FACTORY SETTINGS
QUIT WITHOUT SAVING
EXIT AND SAVE CHANGES
IMPORTANT
If you have password protection enabled for the configuration utility, the Enter
Password screen appears first. You must correctly enter the password before the
Dome Configuration Menu will appear. For information about entering the
password, refer to Entering the Dome's Password on page 1–3.
1–2 SpeedDome Ultra VII Operator's Manual
Working with the Dome Configuration Utility
Once the Dome Configuration Menu is displayed, you may select a menu item, and then modify the
settings you want to change. The following table summarizes the controller commands for SensorNet,
RS-422, and Manchester protocols. For combination keystrokes, press and hold each button in
sequence, then release.
If you want to … Use …
Move the highlight bar.
Select the highlighted item on the screen.
Increase the value of the selected setting or display the next
choice for the setting
Decrease the value of the selected field, or display the
previous choice for the field.
During naming, move the cursor to the right of the current
character in the name.
During naming, move the cursor to the left of the current
character in the name.
Save changes and exit the utility from any screen.
Entering the Dome's Password
A dome password can be used to prevent unauthorized users from starting the configuration utility. If
password protection is enabled the Enter Password screen appears when the command to start the
configuration utility is entered.
Pan/Tilt
Focus
Zoom In
Zoom Out
Zoom In
Zoom Out
Iris Close, then Focus
ENTER PASSWORD
PASSWORD: ********
ABCDEFGHIJKLMNOPQRST
UVWXYZabcdefghijklmn
opqrstuvwxyz 0123456
789/-
Blank Space
CONTINUE
Character
CANCEL
Users must enter the password before the Dome Configuration Menu displays. The password may be
from 1 to 8 characters long.
Using the Dome Configuration Utility 1–3
To enter the password using SensorNet, RS-422, or Manchester protocols:
1. Use the Pan/Tilt control to move the highlight the appropriate character.
2. Press Focus to select the highlighted character.
If you need to change a character that has been entered:
• Zoom In moves the cursor to the right in the Password field.
• Zoom Out moves the cursor to the left in the Password field.
As each character in the password is selected, asterisks (*) appear in the Password field. When you
have finished entering the password, select Continue. If the correct password has been entered, the
Dome Configuration Menu appears. If the correct password was not entered, the Enter Password
screen remains on the monitor.
If you do not want to start the configuration utility, select Cancel to return to normal dome
operation.
IMPORTANT
If you forget the password, contact your Sales Representative for assistance.
For information about programming and enabling password protection, see Chapter 6.
Restoring Factory Settings
Some screens provide a choice to restore factory settings. This choice applies only to those settings currently
displayed on the screen. To reset all configuration settings, choose Reset to Factory Settings from the
Dome Configuration Menu. The following prompt appears:
Press Zoom to display the options.
• If you want to restore the factory settings, select Yes.
• If you do not want to restore the factory settings, select No.
Press Focus to accept the displayed option.
IMPORTANT
Reset to Factory Settings
No
Selecting Reset to Factory Settings from the Dome Configuration Menu does not change
the following settings: Camera Name, Alarm Names, Area Names, Preset Names, Pattern
Names, Area Boundaries, Privacy Zones, and Presets. To reset names to the default settings, see
Chapter 5: Configuring Text Displayed On-Screen.
1–4 SpeedDome Ultra VII Operator's Manual
Exiting the Configuration Utility
Under SensorNet, RS-422, and Manchester protocols, you may save your changes and exit the utility from any
screen by pressing and holding Iris Close, then pressing Focus. From the Dome Configuration Menu, you
have two choices for exiting the utility: Exit and Save Changes or Quit Without Saving. Use the
Pan/Tilt control to move the highlight bar up and down on the screen.
• If you want to keep the changes you made, move the highlight bar to Exit and Save Changes, and select.
The utility closes.
• If you want to exit without making changes, move the highlight bar to Quit Without Saving, and select.
The following prompt appears on the screen:
Press Zoom to display the options.
• To cancel the changes, select Yes.
• To keep the changes, select No. If you choose No, the Dome Configuration Menu is displayed.
Press Focus to accept the displayed option.
IMPORTANT
The following settings do not restore when selecting Quit Without Saving from the Dome
Configuration Menu: Area Boundaries and AGC/Shutter Limit.
Data Not Saved. Quit Anyway?
No
Accessing the Quick Set Menu
SpeedDome Ultra VII provides a Quick Set Menu for commonly used features and functions when
used with compatible controllers. This allows you to change or activate features without starting the
dome configuration menu.
0 TOGGLE QUICK SET MENU
1 DOME CONFIG MENU
2 AUTO IRIS/AUTO FOCUS
3 FLIP
4 PEEL PATTERN
15 SMOOTH SCAN
16 STEPPED SCAN
17 RANDOM SCAN
20 DOME INFORMATION
To access a feature on the menu, enter the number and press the Quick Set button (varies by
controller). The following provides a description of the available options.
Using the Dome Configuration Utility 1–5
Quick Set Command Description
0+Quick Set
1+ Quick Set
2+ Quick Set
3+ Quick Set
4+ Quick Set
15+ Quick Set
16+ Quick Set
17+ Quick Set
Toggles between displaying and hiding the quick set menu.
Displays the SpeedDome Ultra configuration menu. Refer to the dome
manual for information about the available settings.
Resumes Auto Focus/Auto Iris mode.
Rotates the SpeedDome 180° from its current pointing direction. This is
the same as pressing the Flip button on controllers with that feature.
Runs the default Apple Peel Pattern continuously.
Initiates a smooth scan between the left and right scan limits, starting at
the left scan limit. If no scan limits have been set, initiates a smooth 360°
clockwise rotation around the dome axis using the current tilt, zoom and
focus settings.
Initiates a scan between the left and right scan limits pausing briefly
every 10° (at 1x zoom), starting at the left scan limit. When the right scan
limit is reached, the scan is reversed. If no scan limits have been set,
initiates a clockwise rotation around the dome axis pausing briefly every
10° (at 1x zoom) for 3 seconds using the current tilt, zoom and focus
settings.
Initiates a scan between the left and right scan limits pausing randomly
between the limits. If no scan limits have been set, initiates a clockwise or
counter-clockwise rotation around the dome axis using the current tilt,
zoom and focus settings. The dome pauses randomly as it rotates around
the axis.
20+ Quick Set
Displays the Dome Information screen available through the dome
configuration menu.
Refer to your controller instructions to determine if the Quick Set Menu is supported.
1–6 SpeedDome Ultra VII Operator's Manual
Where To Go Next
Now that you understand how to start and work with the Dome Configuration Utility, you are ready
to begin changing the settings for your dome. Use the following chart to determine which chapters
you should use next.
Chapter Topics Covered
Chapter 2: Configuring Pan, Tilt,
Zoom, and Synchronization Options
Chapter 3: Configuring Camera
Features
Chapter 4: Configuring Alarms,
Areas, Home, Privacy Settings, Presets
and Scan Limits
Chapter 5: Configuring Text
Displayed On-Screen
Chapter 6: Configuring Language and
Password Settings
Chapter 7: Displaying Dome
Information
− Set the “flip” feature to rotate the dome 180°
− Set the first zoom stop (22X or 33X) and maximum zoom (up
to 242X)
− Set line lock to prevent vertical rolling when switch in g
between cameras
− Enable automatic or manual White Balance settings (red and
blue values)
− Set the open shutter options to improve camera performance in
low light situations
− Enable automatic or manual Gain settings and set maximum
gain values
− Set alarm actions to initiate a preset, pattern, or no action when
alarm conditions are detected
− Configure normal input states for alarms to be open or closed
− Send input states to host controller
− Set a “home” position for dome
− Establish a North position for use with the direction indicators
− Program Privacy Zones to prevent operators from viewing
restricted areas
− Program area boundaries
− Program presets
− Set scan limits
− Display or hide dome status information
− Display or hide camera, preset, pattern, area or alarm name
information
− Display diagnostic information or “splash” screen during dome
reset
− Display direction indicators
− Assign names to camera, presets, patterns, areas, and alarms
− Reset all names to factory defaults
− Set text attributes (outline and translucent characters)
− Choose the language for the menus and prompts
− Set a password to limit access to the Dome Configuration
Utility
− Enable or disable password protection
− Display dome version information
− Display dome performance statistics
Using the Dome Configuration Utility 1–7
Chapter Topics Covered
Appendix A: SensorNet and
RS-422 Command Summary
Appendix B: Manchester
Command Summary
Appendix C: Pelco Coaxitron and “P”
Protocols Command Summary
Appendix D: Panasonic Up-the-Coax
Command Summary
Appendix E: AD Up-the-Coax
Command Summary
Appendix F: Vicon Protocol
Command Summary
Appendix R: Dome Configuration
Records
Appendix S: Software License
Agreement
− Summarizes the controller commands available for
SensorNet/RS-422
− Summarizes the controller commands available for Manchester
− Performance limitations for Manchester
− Summarizes the controller commands available for Pelco
Coaxitron and “P” protocols
− Performance limitations for Coaxitron and “P” protocols
− Summarizes the controller commands available for Panasonic
UTC protocol
− Performance limitations for UTC protocol
− Summarizes the controller commands available for AD-UTC
protocol
− Summarizes the controller commands available for the Vicon
protocol
− Lists the default dome settings
− Provide space for documenting changes to settings
− Lists the terms and conditions for using this product
Keeping Records for the Dome's Settings
Keep records for each SpeedDome Ultra VII camera dome installed at your facility.
Appendix R: Dome Configuration Records summarizes the default values for each configuration
setting. Space is provided for documenting the settings you change. Note any changes you make to
the dome settings.
1–8 SpeedDome Ultra VII Operator's Manual
CHAPTER 2
Configuring Pan, Tilt, Zoom, and Synchronization Options
This chapter describes the use of the Pan/Tilt/Zoom/Sync Opts menu. Use this screen to set the
Auto Flip feature, configure the Zoom Stop settings, and set the Line Lock option.
In This Chapter
• Overview of Pan / Tilt / Zoom/Synchronization Options Screen ................................2–2
• Setting the Automatic “Flip” Feature...........................................................................2–2
• Adjusting the Zoom Stop Settings ...............................................................................2–3
• Configuring the Line Lock Setting ..............................................................................2–4
• Configuring the Freeze Frame Setting.........................................................................2–5
• Configuring Auto Iris/Auto Focus Resume Settings....................................................2–6
• What To Do Next.........................................................................................................2–7
Overview of Pan / Tilt / Zoom/Synchronization Options Screen
When Pan/Tilt/Zoom/Sync Opts is selected from the Dome Configuration Menu, the following
screen appears:
PROPORTIONAL FLIP OFF/ON
1ST ZOOM STOP X 33/22
MAX TOTAL ZOOM X 44...242
LINE LOCK ON/OFF
FREEZE FRAME OFF/ON
I/F RETURN TO AUTO OFF/ON/
IRIS/FOCUS
Use this screen to enable or disable the “automatic flip” feature, configure the zoom stop settings, set
the line lock options, change the freeze frame settings, and return to auto iris/auto focus settings.
• To change the settings, move the highlight bar to appropriate field and make the changes.
• To change the settings for this screen to the factory defaults, select Reset to Factory Settings.
• To return to the Dome Configuration Menu, select Exit.
Setting the Automatic “Flip” Feature
Use the automatic (proportional) “flip” feature when you need to track someone who walks directly
under the dome and continues on the other side. You start the flip by moving the tilt control to its
lower limit and holding for a brief period. When the flip engages, the dome automatically rotates
180°. You may then continue to track the person as long as the tilt control stays in its lower limit.
Once the tilt control is released, the dome resumes normal operation.
The dome is initially installed with the automatic flip feature disabled. In this situation, the dome
stops when the tilt down reaches its lower limit.
Changing the Automatic Flip Setting
1. Select Pan/Tilt/Zoom/Sync Opts from the Dome Configuration Menu.
The highlight bar appears on the Proportional Flip setting.
2. Change the setting.
• Select On to enable the flip feature.
• Select Off to disable the flip feature.
The default setting is Off.
3. Select Exit. The Dome Configuration Menu appears. Continue with What To Do Next on page
2–7.
2–2 SpeedDome Ultra VII Operator's Manual
Adjusting the Zoom Stop Settings
The SpeedDome Ultra VII includes a 22X optical zoom camera with 11X digital zoom capability.
The maximum possible zoom is 242X. Zoom stop settings define how the zoom function is
partitioned. Depending on the current zoom level, the camera will either stop at the first zoom stop
setting or continue to the maximum zoom setting. The following example explains how zoom stop
settings work.
The default camera settings are 33X for the first zoom stop setting and 88X for the maximum zoom
setting. If the current zoom level is less than 33X, pressing Zoom In continuously causes the zoom to
stop at 33X. If the zoom level is 33X or greater, pressing Zoom In continuously causes the zoom to
stop at the maximum zoom setting of 110X. The second zoom stop remains in effect until the zoom
function is reduced to less than the first zoom stop setting (33X) and the zoom button is released for
one second or longer. To achieve higher zoom levels, change the maximum zoom setting.
2X is the margin of error for the zoom stop settings.
Changing the Zoom Stop Settings
1. Select Pan/Tilt/Zoom/Sync Opts from the Dome Configuration Menu.
2. To change the first zoom stop, continue with step 3. To change the maximum zoom setting,
continue with step 5.
3. Move the highlight bar to 1st Zoom Stop X. Change the setting.
• Select 22 to set the first zoom stop to 22X magnification.
• Select 33 to set the first zoom stop to 33X magnification.
The default setting is 33X.
4. To change the maximum zoom setting, continue with step 5. Otherwise, continue with step 6.
5. Move the highlight bar to the Max Total Zoom X setting. Change the value of the setting.
• The values for the setting are: 44, 66, 88, 110, 132, 154, 176, 198, 220, and 242X
magnification.
The default setting is 88X.
6. Select Exit. The Dome Configuration Menu appears. Continue with What To Do Next on page
2–7.
Configuring Pan, Tilt, Zoom, and Synchronization Options 2–3
Configuring the Line Lock Setting
Use the Line Lock setting to prevent vertical rolling or adjust the appearance of overlay text on color
monitors.
If you experience problems with vertical video rolling when switching multiple cameras to a single
monitor, enabling the Line Lock setting phase locks the video with the AC power line. All cameras
connected to the same power supply will be synchronized. This synchronization prevents the video
from rolling vertically when cameras are switched.
With the Line Lock disabled, the appearance of text displayed on color monitors may be improved.
However, the video will no longer be phase locked with the AC power line. Video may roll vertically
when switching between cameras.
Changing the Line Lock Setting
1. Select Pan/Tilt/Zoom/Sync Opts from the Dome Configuration Menu.
2. Move the highlight bar to Line Lock. Change the setting.
• Select On to enable the line lock. This phase locks the video with the AC power line to
prevent video rolling.
• Select Off to disable the line lock. This stops the phase lock, but may improve the appearance
of text displayed on color monitors.
The default setting is On.
IMPORTANT
Changing the Line Lock setting is not immediate. The dome must reinitialize
(reset) for the change to take place. When the configuration utility is exited,
the following prompt appears:
DOME MUST RESET TO
CHANGE LINELOCK MODE.
RESET DOME NOW?
NO
• If you do not want to reinitialize the dome, select No. Changes to the
Line Lock setting will not take effect.
• If you want to reinitialize the dome, select Yes. Changes to the Line
Lock setting will take effect when the dome finishes the reset.
3. Select Exit. The Dome Configuration Menu appears. Continue with What To Do Next on page
2–7.
2–4 SpeedDome Ultra VII Operator's Manual
Configuring the Freeze Frame Setting
If you need to maintain a static image when calling automatic functions, such as presets or patterns,
use the Freeze Frame setting. This prevents the display of the dome movement and lens adjustments
from being displayed on-screen while the preset or pattern is being sought.
When the Freeze Frame setting is enabled, the scene currently displayed on the monitor will be
preserved (frozen) on-screen until the pattern or preset is ready for display. The image then switches
smoothly to the new scene. You may want to use this setting if using a digital video recorder.
For example, if the dome is installed in a lobby of a busy building, you may want to program presets
that show different areas in the lobby. Figure 2-1 shows a sample floor plan for the lobby.
Figure 2-1: Lobby Floor Plan
Security
Office Door
Waiting
Area
Entry
Dome
Reception
Desk
Hallway
Elevator
If Freeze Frame is disabled, each time the dome points to a different preset, you will see the dome’s
movement to the new scene, as well as any lens adjustments that are required. For example, if the
dome is currently pointing at Reception Desk, and the preset number assigned to the Entry is selected,
you will see a blur of motion as the dome quickly pans past other areas in the lobby before focusing
on the Entry scene.
If Freeze Frame is enabled, the current scene is displayed on-screen until all dome movement and
lens adjustments are complete. For example, the Reception Desk scene will be frozen on-screen until
the dome completes the movement and lens adjustments necessary to display the selected preset.
When the adjustments are finished, the Entry scene is automatically displayed.
Configuring Pan, Tilt, Zoom, and Synchronization Options 2–5
Changing the Freeze Frame Setting
1. Select Pan/Tilt/Zoom/Sync Opts from the Dome Configuration Menu.
2. Move the highlight bar to Freeze Frame. Change the setting.
• Select On to enable Freeze Frame. This freezes the current scene when presets or patterns are
selected.
• Select Off to disable Freeze Frame. This displays the dome motion and lens adjustments when
presets or patterns are selected.
The default setting is Off.
3. Select Exit. The Dome Configuration Menu appears. Continue with What To Do Next on page
2–7.
Configuring Auto Iris/Auto Focus Resume Settings
Normally, the camera’s iris and focus settings return to automatic mode when the dome moves a
minimum of one frame from its current pointing position. In some situations, you may want to
maintain specific iris and/or focus adjustments based upon your surveillance needs.
Use the I/F Return to Auto setting to configure the auto iris and auto focus resume settings. Four
settings are available.
Setting Description
ON
OFF
IRIS
FOCUS
Both return to auto iris and return to auto focus settings are enabled.
Moving the dome resumes auto mode for both iris and focus changes.
Both return to auto iris and return to auto focus settings are disabled.
Moving the dome does not resume auto mode for iris and focus changes.
Only return to auto iris is enabled. Return to auto focus is disabled.
Moving the dome resumes auto iris mode without changing focus settings.
Only return to auto focus is enabled. Return to auto iris is disabled.
Moving the dome resumes auto focus mode without changing iris settings.
Changing the Auto Iris/Auto Focus Resume Setting
1. Select Pan/Tilt/Zoom/Sync Opts from the Dome Configuration Menu.
2. Move the highlight bar to I/F Return to Auto. Change the setting.
• Select On to enable both resume auto iris and resume auto focus.
• Select Off to disable both resume auto iris and resume auto focus.
• Select Iris to enable resume auto iris only.
• Select Focus to enable resume auto focus only.
The default setting is On.
3. Select Exit. The Dome Configuration Menu appears. Continue with What To Do Next on page
2–7.
2–6 SpeedDome Ultra VII Operator's Manual
What To Do Next
When you select Exit from the Pan/Tilt/Zoom screen, the Dome Configuration Menu appears.
DOME CONFIGURATION MENU
Chapter 2
Chapter 3
Chapter 4
Chapter 5
Chapter 6
Chapter 7
PAN/TILT/ZOOM/SYNC OPTS
CAMERA FUNCTIONS
ALARMS/AREAS/PRESETS/PZ
ON-SCREEN TEXT DISPLAY
LANGUAGE / PASSWORD
DOME INFORMATION
RESET TO FACTORY SETTINGS
QUIT WITHOUT SAVING
Chapter 1
EXIT AND SAVE CHANGES
From this screen you can:
• Select an option to make additional changes.
• Restore all settings to the factory defaults.
• Exit the utility without saving changes.
• Save the changes and exit the utility.
Move the highlight bar to an item and select it. Refer to the related chapter for additional information.
Configuring Pan, Tilt, Zoom, and Synchronization Options 2–7
NOTES:
2–8 SpeedDome Ultra VII Operator's Manual
CHAPTER 3
Configuring Camera Features
This chapter describes the settings used to control the camera features. It describes how to change the
white balance settings, automatic gain control, and open shutter settings to improve camera
performance.
In This Chapter
• Overview of Camera Settings ......................................................................................3–1
• Adjusting White Balance Settings ...............................................................................3–2
• Working with AGC and Open Shutter Settings...........................................................3–3
• What To Do Next.........................................................................................................3–6
Overview of Camera Settings
When Camera Functions is selected from the Dome Configuration Menu, the following screen
appears:
Auto White Bal OFF/ON
W Bal Adj: Red 0-511 Blue 0-511
AGC/Shutter Max Gain Limit
Open Shutter(NTSC)0-28 dB 1/2-1/60 s
Open Shutter(PAL) 0-28 dB 2/3-1/50 s
From this screen you can adjust the white balance settings, set the IR mode for the camera, enable or
disable Wide Dynamic Range, set the automatic gain control (AGC) feature, adjust the AGC level,
and configure the open shutter settings.
CAMERA FUNCTIONS
RESET TO FACTORY SETTINGS
EXIT
• To change settings, move the highlight bar to the appropriate field and make the changes.
• To change the settings for this screen to the factory defaults, select Reset to Factory Settings.
• To return to the Dome Configuration Menu, select Exit.
Adjusting White Balance Settings
r
White balance is normally compensated for by the automatic white balance gain control. In some
lighting conditions, you may need to manually adjust the red and blue settings for optimal viewing.
When Automatic White Balance is enabled, the red and blue setting values are based on feedback
from the camera. When Automatic White Balance is disabled, the camera uses the red and blue
setting values to control the white balance. When Automatic White Balance is first switched from
On to Off, the red and blue values displayed are based on the current feedback from the camera. The
red and blue values range from 0 to 511. Changes occur in increments of 5.
The following chart illustrates the red and blue settings relationship to white balance.
Maximum
Blue
WHITE BALANCE
Both Red and Blue
settings are set to
maximum values.
Maximum
511
Red
Minimum
511
0
Blue
Minimum
Red
On-screen Colo
appears Magenta
(Purple)
On-screen Color
appears Green
0
As the value for the red setting increases, the image appears more red. As the value decreases, the
image appears less red.
As the value for the blue setting increases, the image appears more blue. As the value decreases, the
image appears less blue.
As the values for both the red and blue settings are increased, the image appears more magenta
(purple). As the values for both the red and blue settings are decreased, the image appears more
green.
Tip: Auto White Bal must be set to Off to manually change the Red and Blue settings.
Changes to the red and blue settings occur in increments of 5.
3–2 SpeedDome Ultra VII Operator's Manual
Changing Automatic White Balance Settings
1. Select Camera Functions from the Dome Configuration Menu. The highlight appears on the
Auto White Bal setting.
2. Change the setting.
• Select Off to manually adjust the red or blue settings. Continue with step 3.
• Select On for automatic white balance. Continue with step 7.
The default setting is On.
3. Do one of the following:
• To change the red setting, move the highlight bar to W Bal Adj: Red, then continue with
step 4.
• To change the blue setting, continue with step 5.
4. Adjust the red setting. The values range from 0 to 511.
There is no default value for the red setting.
5. Do one of the following:
• To change the blue setting, move the highlight bar to Blue, then continue with step 6.
• If you are finished making changes, continue with step 7.
6. Adjust the blue setting. The values range from 0 to 511.
There is no default value for the blue setting.
7. Select Exit. The Dome Configuration Menu appears. Continue with What To Do Next on
page 3–6.
Working with AGC and Open Shutter Settings
The SpeedDome Ultra VII dome provides settings for compensating for low-light scenes in color:
Automatic Gain Control and Open Shutter. Automatic Gain Control (AGC) amplifies the video signal
in scenes with minimal light. Many low-light scenes result in picture noise. As gain is increased, the
picture noise is also amplified.
When AGC is enabled, the camera automatically adjusts the gain setting value. When AGC is
disabled, no gain is applied to the video signal. This may make the video appear darker on the
monitor.
The gain setting for the camera differs from the maximum gain (Max Gain) setting available on the
Camera Functions menu. The Max Gain setting is an upper limit for how much gain can be
increased when AGC is enabled. The trade-off between picture level (brightness) and noise may be
adjusted by setting the Max Gain value. Lower values for Max Gain setting may result in a darker
picture with less noise. Higher values for Max Gain setting may result in a brighter picture with more
noise.
In addition to the AGC settings, you may also adjust the Open Shutter settings to improve dome
performance in low light conditions. For more information, continue with Understanding How
Advanced Shutter Settings Improve Low-Light Performance.
Configuring Camera Features 3–3
Understanding
How Advanced Shutter Settings Improve Low-Light Performance
The camera dome supports the ability to view color images from extremely low-light situations.
feature is called Open Shutter and is only in effect during low-l
not be obtainable otherwise. It does not affect the camera performance in norm
ight situations where an image would
al or bright light
situations.
When the Open Shutter is enabled and the scene illumination is too low to obtain a clear image at the
normal video rate, the camera collects luminance information from multiple fields. As it does so, the
current video information is retransmitted until new information is available from the camera. U
these condi
tions, moving objects will appear blurred, and still images may appear blurred, choppy,
and with more static than video obtained under normal lighting conditions.
The Shutter Limit value sets the video update time in fractions of a second. Depending on the
lighting conditions, the video information may be updated more frequently, but no slower than the
limit set.
Figure 3–1 illustrates a Shutter Limit of 1/4.
This
nder
Figure 3–1
Red Light Red Light Red Light Green Light
: Graphical view of Shutter Limit settings
250 2
msec
50
msec
180
msec
In this example, the dome receives information about the color of the traffic light. While the light is
red, the image is relatively static. With the shutter limit set to 1/4 second (250 milliseconds), updated
red light information is transmitted at 1/4-second intervals. When the light changes from red to green,
updated light color information becomes available. The dome must now transmit information about
the green light. This update occurs as soon as the green light information is available. This may occu
r
before the 1/4-second interval elapses. In this example, the light changed to green after 180milliseconds. Thereafter the green light information is transmitted at 1/4-second intervals until new
light color information becomes available.
If the light were to change from red to green halfway through the field integration interval (125
milliseconds), it may appear that both the red and green lights are lit simultaneously. This situation i
s
illustrated in Figure 3–2.
Figure 3–2: Mixed field integration
Red Light Red Light Red/Green Light Green Light
250
msec
125
msec
125
msec
Adjusting the Shutter Limit sets the update time used to maintain the image quality. If you want to
videotape an incident in low-light conditions, you may find that tape quality is not acceptable. To
ensure that the videotape quality is acceptable for possible prosecution purposes, you may want to test
the Shutter Limit settings under the expected lighting conditions.
3–4 SpeedDome Ultra VII Operator's Manual
Loading...