American Dryer ADG-385, WDA-385 User Manual

ADG-385/WDA-385

Parts Manual

24 VAC Phase 5

1996/1997

American Dryer Corporation

88 Currant Road

Fall River, MA 02720-4781

T elephone: [phone] / Fax: [phone]

E-mail: [e-mail]

ADC Part No. 450195

Retain This Manual In A Safe Place For Future Reference

American Dryer Corporation products embody advanced concepts in engineering, design, and safety. If this

product is properly maintained, it will provide many years of safe, efficient, and trouble-free operation.

ONLY properly licensed technicians should service this equipment.

OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the in­stallation/operator's manual included with the dryer.

WARNING:

WARNING: The dryer must never be operated with any of the back guards, outer tops, or

We have tried to make this manual as complete as possible and hope you will find it useful. ADC reserves the
right to make changes from time to time, without notice or obligation, in prices,
specifications, colors, and material, and to change or discontinue models.

UNDER NO CIRCUMSTANCES should the door switch or the heat circuit
devices ever be disabled.

service panels removed. PERSONAL INJURY or FIRE COULD RESULT.

Important

For your convenience, log the following information:

DATE OF PURCHAS E MODEL NO.

DIS TRI BUT ORS N AME

Serial Number(s)

Replacement parts can be obtained from your distributor or the ADC factory . When ordering replacement parts
from the factory, you can FAX your order to ADC at [phone] or telephone your orders directly to the
ADC Parts Department at [phone]. Please specify the dryer model number and serial number in
addition to the description and part number, so that your order is processed accurately and promptly.

The illustrations on the following pages may not depict your particular dryer exactly. The
illustrations are a composite of the various dryer models. Be sure to check the descriptions of the parts thor­oughly before ordering.

INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE USER

SMELLS GAS MUST BE POSTED IN A PROMINENT LOCATION. THE
INSTRUCTIONS TO BE POSTED SHALL BE OBT AINED FROM THE
LOCAL GAS SUPPLIER.

Table of Contents

High Security Control Door Assembly........................................................................... 2

Phase 5 Coin Microprocessor Control Panel Assembly ................................................ 3

Phase 5 Microprocessor Control Box Assembly........................................................... 4

Coin V ault Assembly ...................................................................................................... 5

Main Door “Steel” Assembly..................................................................................... 6, 7

Insulated Front Panel Assembly ..................................................................................... 8

Main Door Switch Assembly ......................................................................................... 9

Drop Lint Door Assembly............................................................................................ 10

Lint Trap Assembly...................................................................................................... 11

Basket (Tumbler) / Support Assemblies................................................................. 12, 13

Tumbler Bearing Assembly .................................................................................... 14, 15

Idler Bearing Assembly .......................................................................................... 16, 17

Totally Enclosed, Fan-Cooled (T.E.F.C.) Motor Mount Assembly ....................... 18, 19

Sensor Bracket Assemblies .................................................................................... 20, 21

Direct Spark Ignition (DSI) Burner Assembly........................................................ 22, 23

ADG-385 Sail Switch / Hi-Limit Assembly ............................................................ 24, 25

Single Phase Motor, Electric Relay Panel Assembly .................................................... 26

Outer Top / Back Guard Assembly.............................................................................. 27

Microprocessor Coin Acceptor Listing ....................................................................... 28

Step Down Transformer Usage Listing ........................................................................ 29

Additional Parts A vailable ............................................................................................ 30

High Security Control Door Assembly

Illus. No. Part No. Qty. Description

1 160038 1 XX4451 Lock Assembly with Hardware
2 160140 1 XX4451 Key ONLY
3 160031 1 Lock Cam
4 112347 1 Wascodry Logo
5 881434* 1 High Security Control Door Assembly Less Lock

(includes illus. nos. 5 through 8)

881435* 1 High Security Textured Control Door Assembly LessLock

(includes illus. nos. 5 through 8)
6 180303 1 Top Black Trim Strip with Lock Hole
7 117603 3 Suppressor Tape/Gasket (sold in feet)
8 150201 4 #10-32 x 1/4” Phillips Round Head Machine Screw
9 150300 4 #10 x 1/2” Hex Washer TEK Screw
10 102600 1 Control Door Support Rod Catch
1 1 102601 1 Control Door Rod Retainer Clip
12 102505 1 Control Door Support Rod
13 117602 2 Suppressor Tape/Gasket (sold in feet)

* Specify color when ordering.

2 American Dryer Corp. 450195-3

Phase 5 Coin Micropr ocessor Contr ol Panel Assembly

Illus. No. Part No. Qty. Description

1 112526 1 Coin Keyboard Label Assembly
2 881506 1 Coin Control Panel Assembly Less Acceptor

(includes illus. nos. 1, 2, 4, 5, 6 and 11)

881507 1 Coin Control Panel Assembly with Battery Bracket

Less Acceptor (includes illus. nos. 1, 2, 4, 5, 6 and 11)
881540 1 Coin Control Panel ONLY
881430 1 Coin Control Panel with Battery Bracket ONLY

3 150309 1 #10-16 x 1/2” HH TEK Crimptite Screw
4 137213 1 Phase 5 Coin Controller ONLY

824998 1 Phase 5 Battery Clip

5 153010 2 #6 S tar Washer
6 150005 2 #6-32 x 1/4” Phillips Round Head Machine Screw
7 --------- 1 Microprocessor Coin Acceptor with Optical Switch

(refer to Microprocessor Coin Acceptor Listing on page 28)

8 137056 1* Optic Switch ONLY
9 37023 1* Optic Switch Connector ONLY
10 137021 3* Microprocessor Socket ONLY

880772 1 Single Coin Optical Switch Harness
824080 1 Dual Coin Optical Switch Harness
122800 1 Microprocessor (female) Pin Extraction Tool

11 136048 1 1/8-Amp (Slo Blo) Fuse ONLY

* For Dual Coin Models, double the quantity.

450195-3 www.amdry.com 3

Phase 5 Micropr ocessor Contr ol Box Assembly

Illus. No. Part No. Qty. Description

1 --------- 1 Step Down Transformer

(refer to Step Down Transformer Usage Listing on page 29)

2 150300 2 #10 x 1/2” Hex Washer TEK Screw
3 120715 1 30-Position T erminal Block
4 150002 2 #6-32 x 1” Slotted Round Head Machine Screw
5 151000 2 #6-32 Pal Nut
6 136057 * 1/2-Amp (Slo Blo) Fuse
7 150301 * #8 x 7/16” Phillips Pan Head TEK Screw
8 136008 * Fuse Block/Strip ONLY
9 122641 1 15-Pin Microprocessor Connector
10 122706 * Socket T erminal ONLY
1 1 121400 1 7/8” Universal Bushing

* As required.

4 American Dryer Corp. 450195-3

Coin Vault Assembly

Illus. No. Part No. Qty. Description

1 881431 1 Microprocessor Coin Vault Assembly Complete

(includes illus. nos. 1 through 6)

802123 1 Microprocessor Coin Vault ONLY
2 160006 Cam for 1/4-Turn Lock ONLY
3 875061 1 1/4-Turn Lock Assembly

(includes illus. nos. 2 and 3)
160007 1 1/4-Turn Lock with Key ONLY
160105* 1 1/4-Turn Mer-Pel Key ONLY

4 802020 1 1/4-Turn Coin Box Assembly

(includes illus. nos. 2 through 4)
802019 1 1/4 Turn Coin Box ONLY W ithout Faceplate

5 802018 1 1/4 T urn Coin Box Faceplate ONLY
6 152014 4 1/4-20 Free Spin Wash Nut
7 309250 1 Coin V ault Slot Cover

* Specify key number when ordering.

450195-3 www.amdry.com 5

Main Door “Steel” Assembly

6 American Dryer Corp. 450195-3

Main Door “Steel” Assembly

Illus. No Part No. Qty. Description

1 8 8 1150 1 Black Main Door Assembly Complete

(includes illus. nos. 1, 2, 8-15)
881207 1 Stainless Steel Main Door Assembly Complete

(includes illus. nos. 1, 2, 8-15)

2 102349 1 Door Gasket

170731 1 Gasket Adhesive (Black) 10.7 oz. Cartridge
170730 1 Gasket Adhesive (Clear) 10.7 oz. Cartridge

3 8 8 1152 1 Top Hinge Block (Black)

(includes illus. nos. 3 and 4)
881208 1 Top Hinge Block (Stainless Steel)

(includes illus. nos. 3 and 4)

4 150445 2 1/4-20 x 3/4” Black Cap Head Set Screw

150443 2 1/4-20 x 3/4” Stainless Steel Cap Head Set Screw
53031 1 1/4” Nylon Washer

6 8 8 1 1 5 1 1 Bottom Hinge Block (Black)

(includes illus. nos. 5, 6 and 7)
881209 1 Bottom Hinge Block (Stainless Steel)

(includes illus. nos. 5, 6 and 7)

7 150445 2 1/4-20 x 3/4” Black Cap Head Set Screw

150443 2 1/4-20 x 3/4” Stainless Steel Cap Head Set Screw

8 150683 3 Black 1/4-20 x 5/8 Carriage Bolt

150682 3 Polished 1/4-20 x 5/8 Carriage Bolt

(for models with stainless steel doors)

9 152014 3 1/2-20 Free Spin Wash Nut
10 151010 1 10-32 Hex Acorn Nut (Black)

151009 1 10-32 Hex Acorn Nut (Stainless Steel)

11 150120 1 Door Latch Screw
12 150683 3 Black 1/4-20 x 5/8 Carriage Bolt

150682 3 Polished 1/4-20 x 5/8 Carriage Bolt

(for models with stainless steel doors)

13 152014 3 1/2-20 Free Spin Wash Nut
14 881210 1 Black Main Door Handle ONLY

170333 1 Stainless Steel Main Door Handle ONLY

15 102211 1 20-9/16” Door Glass with Notch

170731 1 Glass Adhesive (Black) 10.3 oz. Cartridge
170730 1 Glass Adhesive (Clear) 10.3 oz. Cartridge

450195-3 www.amdry.com 7

Insulated Front Panel Assembly

Illus. No. Part No. Qty. Description

1 881510 1* Insulated Front Panel Assembly

(includes illus. nos. 1, 2, 3 and 6)

881509 1* Textured and Insulated Front Panel Assembly

(includes illus. nos. 1, 2, 3 and 6)
2 154215 2 5/32” Pop Rivet
3 170330 1 Friction Door Latch
4 150300 1 #10 x 1/2” Hex Washer TEK Screw
5 150415 8 #10-16 x 1/2” Phillips Round Head Screw
6 116526 1 Front Panel Insulation

* Specify color when ordering.

8 American Dryer Corp. 450195-3