Mega Bar 50RGB RC Introduction
Unpacking: Thank you for purchasing the Mega Bar 50RGB RC by
American DJ®. Every Mega Bar 50RGB RC has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your xture for any damage and be sure all accessories necessary to operate
the unit has arrived intact. In the case damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Do not return this unit to your dealer without rst
contacting customer support.
Introduction: The Mega Bar 50RGB RC is part of American DJ’s con-
tinuing pursuit for creating high quality affordable intelligent fixtures.
The Mega Bar 50RGB RC is a DMX intelligent LED color wash. This
wash can be used in a stand alone mode or connected in a Master/
Slave conguration. The unit can also be controlled via DMX controller. This unit has seven operating modes: Manual Color mode, Color
Change mode, Color Fade mode, Auto mode, Sound Active mode,
RGB Manual Control mode and DMX control mode.
Customer Support: American DJ® provides a toll free customer sup-
port line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 9:00 a.m. to
5:00 p.m. Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
9/10
User Instructions
American DJ®
6122 S. Eastern Ave.
Los Angeles Ca. 90040
www.americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ®.
PLEASE recycle the shipping carton when ever possible.
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 2
Mega Bar 50RGB RC General Instructions
Mega Bar 50RGB RC Safety Precautions
To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.
Mega Bar 50RGB RC Features
• Mulit-Colors (32 Colors to choose from)
• 7 Operating Modes
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• 7 DMX Channel Modes: 1, 2, 3, 4, 5, 6, or 7 DMX Channels
Mega Bar 50RGB RC Warranty Registration
The Mega Bar 50RGB RC carries a 3 year (1095 days) limited warranty. Please fill out the enclosed warranty card to validate your
purchase and warranty. You may also register your product online at
www. americandj.com. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty you must provide a
copy of your proof of purchase invoice. Please contact American DJ®
customer support for a R.A. number.
Mega Bar 50RGB RC Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 3 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 4©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 3
Mega Bar 50RGB RC Set Up
DMX512 IN
3-PIN XLR
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
1
2
3
1
2
3
DMX +
DMX -
COMMON
DMX512 OUT
3-PIN XLR
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Mega Bar 50RGB RC Set Up
Power Supply: The American DJ® Mega Bar 50RGB RC contains a
electronic ballast, which will auto sense the voltage when it is plugged
into the power source. With the electronic ballast you do not need to
worry about wall voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Mega Bar 50RGB RC has 7 DMX Channel Modes. The DMX address
is set on the rear panel of the Mega Bar 50RGB RC. Your unit and your
DMX controller require a approved DMX-512 110 Ohm Data cable for
data input and data output (Figure 1). We recommend Accu-Cable DMX
cables. If you are making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be
purchased at almost all professional sound and
lighting stores). Your cables should be made with
a male and female XLR connector on either end
of the cable. Also remember that DMX cable must
be daisy chained and cannot be split.
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 5
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
Figure 2
XLR Male Socket
1 Ground
2 Cold
3 Hot
Figure 3
Special Note: Line Termination.
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
5-Pin XLR DMX Connectors.
connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures
may be implemented in a 3-pin XLR DMX line. When inserting stan-
Figure 1
dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 6
XLR Female Socket
2 Cold
1 Ground
3 Hot
When longer runs of cable are
Some manufactures use 5-pin XLR
3-Pin XLR to 5-Pin XLR Conversion
Pin 1
Pin 2
Pin 3
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
Figure 4
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
Mega Bar 50RGB RC Operating Instructions
Mega Bar 50RGB RC Operating Instructions
LED Display On/Off: To make the display stay ON all of the time
press the MODE and UP buttons at the same time. To make the display turn OFF after 20 seconds, press the MODE and DOWN buttons
at the same time.
Operating Modes:
You can use the Mega Bar 50RGB RC in either a stand alone mode
or a master/slave configuration, there are 7 modes to choose from:
• Manual Color Mode - Select one of 32 different colors to remain
static.
• Color Change Mode - In this mode the unit will change through the
different colors, you an adjust the rate of speed.
• Color Fade Mode - In this mode the unit will fade in and out
through the different colors, you an adjust the fade speed.
• Auto Mode - In this mode the unit will change through the color
change and color fade.
• Sound-Active mode - The unit will react to sound, chasing through
the built in programs.
• RGB Manual Control mode - Control the intensity of all three colors
adjusting the intensity to your desire to create you own desired color.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the Elation® Show Designer™.
done with 66 xtures. After 66 you will need to use a new
power outlet. They must be the same xtures. DO NOT mix
xtures.
2. You will also have to link the power cords to each other, as you
did with the XLR cables.
3. Using the Master unit, choose your desired mode or program and
connect the “Slave” unit or units.
4. On the “Slave” unit(s) press the MODE button until “SLAV” is dis played. They will now follow the “Master” unit.
Static Color Mode:
In this mode you can choose a desired color to remain static.
1. Plug the fixture in and press the MODE button until “CO.XX” is dis played. “XX” = 0-32.
2. Press the UP or DOWN buttons to adjust “X” between 0-32.
Color Change Mode:
In this mode the Mega Bar 50RGB RC will change through the different colors.
1. Plug the fixture in and press the MODE button until “JP.XX” is dis played. “XX” = 01-99 which is the adjustable rate of the speed
change.
2. Press the UP or DOWN buttons to adjust the speed of the color
change.
Master-Slave Operation:
This function will allows you to link units together to run in a MasterSlave mode. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only
one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR microphone cables to link your units to gether. Remember that the Male XLR connector is the input and
the Female XLR connector is the output. The first unit in the
chain (master) will use the female XLR connector only. The last
unit in the chain will use the male XLR connector only. Note:
You can also daisy chain the power cords, this can only be
Color Fade Mode:
In this mode the Mega Bar 50RGB RC will fade in and out of the different colors.
1. Plug the fixture in and press the MODE button until “Fd.XX” is dis played. “XX” = 01-99 which is the adjustable rate of the speed
change.
2. Press the UP or DOWN buttons to adjust the speed of the color
change.
Auto Mode:
1. Plug the fixture in and press the MODE button until “AUTO” is
displayed. You are now in AUTO mode and the fixture will now
cycle through the color change and color fade.
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 8©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 7
Mega Bar 50RGB RC Operating Instructions
Mega Bar 50RGB RC ADJ LED RC Operation
Sound Active Mode:
In this mode the Mega Bar 50RGB RC will react to sound, and chase
through the different colors.
1. Plug the fixture in and press the MODE button until “SO.XX” is dis-
played. The fixture will now change color via sound.
2. You can press the UP or DOWN buttons to adjust the sound sensi tivity level. The level can be adjusted from “SO.00” the least sensi tive, to “SO.31” the most sensitive.
RGB Mode:
In this mode you can select either red, green, blue, or adjust the colors to make a deisred color, which will remain static. You can adjust
the intensity of each color to make your desired color.
1. Plug the fixture in and press the MODE button until “drGb” is dis-
played, and press SETUP.
2. You can press the UP or DOWN buttons to adjust the intensity of
the displayed color. When you have adjusted your desired color
press SETUP to scroll to the next color.
DMX Mode:
There are seven DMX Modes to choose from: 1 Channels, 2 Channels,
3 Channels, 4 Channels, 5 Channels, 6 Channels, or 7 Channels.
Operating through a DMX controller give the user the freedom to create their own programs tailored to their own individual needs.
1. This function will allow you to control each individual fixture’s
traits with a Elation® DMX 512.
2. To run your fixture in DMX mode, plug in the fixture via the XLR
connections to any standard DMX controller.
3. Press the MODE button until “d.XXX” is displayed. Press the UP
or DOWN buttons to select your desired address. Once you have
set your desired DMX address press the SETUP button to choose
your desired DMX mode.
4. When you press the SETUP button “CH-X” should be displayed.
“X” represents the DMX Channel mode. Press the UP or DOWN
buttons to select your desired DMX Channel mode. Press the
SETUP button again once you have found your desired DMX
Channel mode.
5. Please see pages 12-15 for DMX values and traits.
The ADJ LED RC infrared remote has many differnet functions and
gives you complete control of your Mega Bar 50RGB RC. To control
the your desired fixture you must aim the controller at the front of the
fixture and be no more the 30 feet away.
BLACKOUT - Pressing this button will blackout the fixture.
AUTO RUN - This button will run an automatic program. You can
control the speed of the Auto Run by pressing the SPEED button first
and then pressing the “+” and “-” buttons.
PROGRAM SELECTION - This button will let you access the units
built-in programs. Pressing this button and then press the “+” or “-”
to navigate through the built-in programs.
FLASH - This button will activate the strobe effect. You can control
the flash rate by pressing the “+” and “-” buttons. Press this button
again to exit strobe mode.
SPEED - Press this button and use the “+” & “-” buttons to adjust the
speed of the Auto run.
DMX MODE - This button will let you select which DMX mode you
want to use. Some fixtures will come with different DMX channel
modes. This button will switch between the different modes. Please
see pages 12-15 for DMX modes, values, and traits.
SOUND ACTIVE - Press this button to activate sound active mode.
Use the “+” & “-” buttons to adjust the sound sensitivity.
SLAVE - This designates the fixture as a slave fixture in a master/
slave configuration.
SET ADDRESS - Press this button to set the DMX address. Press
this button first, then press the numbers to set the address.
Example: DMX Address 1 Press “S001”
DMX Address 245 Press “S245”
R G B - Press either one of these buttons and the press the “+” or “-”
to adjust the brightness.
“+” and “-” - Use these buttons to adjust the flash rate, speed of the
Auto Run, sound sensitivity, and program selection.
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 10©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 9
Mega Bar 50RGB RC ADJ LED RC Operation
Mega Bar 50RGB RC DMX Values & Traits - 1 Channel
DMX Control:
Operating through an Elation® DMX controller gives the user the
freedom to create their own programs tailored to their own individual
needs. Follow the directions below to set your DMX Mode and address.
1. Before connecting to an Elation® DMX controller, your fixture has
different DMX channel modes, please select your desired mode by
pressing the DMX Mode button, then using the “+” or “-” buttons
to scroll through the DMX Channel Modes. Set the mode before
you address the fixture. See the bottom of this page for the DMX
modes.
2. After you have selected your mode, set the DMX address for the
fixture by pressing the “S” button. When the “S” button is pressed
the LED’s will flash 2-3 times and all the red LED’s will light. Use
the number buttons to press in your desired address. See “SET
ADDRESS” on page 10 for examples.
Note: When seeting the DMX address each time a number is pressed
a LED color will glow, when you have set the DMX address correctly
all LED’s will flash 2-3 times.
3. Now you may connect the fixture via the XLR connections to any
standard Elation® DMX controller. Please see pages 12-15 to for a
detailed descriptions of the DMX modes, values, and traits.
• If all of the Red LED’s glow you are in DMX Mode 1: 1 DMX
Channels
• If all of the Green LED’s glow you are in DMX Mode 2: 2 DMX
Channels
• If all of the Blue LED’s glow you are in DMX Mode 3: 3 DMX
Channels
• If Red LED’s & Green LED’s glow you are in DMX Mode 4: 4
DMX Channels
• If Red LED’s & Blue LED’s glow you are in DMX Mode 5: 5 DMX
Channels
• If Green LED’s & Blue LED’s glow you are in DMX Mode 6: 6
DMX Channels
• If all of the LED’s glow you are in DMX Mode 7: 7 DMX Channels
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 11
Channel Value Function
1 COLOR MACROS
0 OFF
1 - 7 COLOR 1
8 - 15 COLOR 2
16 - 23 COLOR 3
24 - 31 COLOR 4
32 - 39 COLOR 5
40 - 47 COLOR 6
48 - 55 COLOR 7
56 - 63 COLOR 8
64 - 71 COLOR 9
72 - 79 COLOR 10
80 - 87 COLOR 11
88 - 95 COLOR 12
96 - 103 COLOR 13
104 - 111 COLOR 14
112 - 119 COLOR 15
120 - 127 COLOR 16
128 - 135 COLOR 17
136 - 143 COLOR 18
144 - 151 COLOR 19
152 - 159 COLOR 20
160 - 167 COLOR 21
168 - 175 COLOR 22
176 - 183 COLOR 23
184 - 191 COLOR 24
192 - 199 COLOR 25
200 - 207 COLOR 26
208 - 215 COLOR 27
216 - 223 COLOR 28
224 - 231 COLOR 29
232 - 239 COLOR 30
240 - 247 COLOR 31
248 - 255 COLOR 32
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 12
Mega Bar 50RGB RC DMX Values & Traits - 2 Channels
Mega Bar 50RGB RC DMX Values & Traits - 5 Channels
Channel Value Function
1 COLOR MACROS
PLEASE SEE CHANNEL 1 MODE
2 MASTER DIMMER
1 - 255 0% - 100%
Mega Bar 50RGB RC DMX Values & Traits - 3 Channels
Channel Value Function
1 RED
1 - 255 0% - 100%
2 GREEN
1 - 255 0% - 100%
3 BLUE
1 - 255 0% - 100%
Mega Bar 50RGB RC DMX Values & Traits - 4 Channels
Channel Value Function
1 RED
1 - 255 0% - 100%
Channel Value Function
1 RED
1 - 255 0% - 100%
2 GREEN
1 - 255 0% - 100%
3 BLUE
1 - 255 0% - 100%
4 MASTER DIMMER
1 - 255 0% - 100%
5 COLOR MACROS
PLEASE SEE CHANNEL 1 MODE
Mega Bar 50RGB RC DMX Values & Traits - 6 Channels
Channel Value Function
1 RED
1 - 255 0% - 100%
2 GREEN
1 - 255 0% - 100%
2 GREEN
1 - 255 0% - 100%
3 BLUE
1 - 255 0% - 100%
4 MASTER DIMMER
1 - 255 0% - 100%
3 BLUE
1 - 255 0% - 100%
4 COLOR MACROS
PLEASE SEE CHANNEL 1 MODE
5 STROBING
0 - 15 OFF
16 - 255 SLOW - FAST
6 MASTER DIMMER
1 - 255 0% - 100%
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 13 ©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 14
Mega Bar 50RGB RC DMX Values & Traits - 7 Channels
Channel Value Function
1 RED
1 - 255 0% - 100%
2 GREEN
1 - 255 0% - 100%
3 BLUE
1 - 255 0% - 100%
4 COLOR MACROS
PLEASE SEE CHANNEL 1 MODE
5 STROBING/PROGRAM SPEED
0 - 15 OFF
16 - 255 SLOW - FAST
6 PROGRAMS
0 - 127 OFF
128 - 159 COLOR MIXING
160 - 191 3 COLOR CHANGE
192 - 223 7 COLOR CHANGE
224 - 255 SOUND ACTIVE
Mega Bar 50RGB RC Photometric Charts
Red
Green
7 MASTER DIMMER
1 - 255 0% - 100%
When using Sound Active mode in Channel 6, Channel 5 will
control the sound sensitivity. Sound Sensitivity will start working
after Channel 5 is past the DMX value of 8.
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 15 ©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 16
Blue
Mega Bar 50RGB RC Fuse Replacement Mega Bar 50RGB RC Photometric Charts
First unplug the power. Locate and remove the unit’s power cord.
Once the cord has been removed located the fuse holder located
inside the power socket. Insert a flat-head screw driver into the power
socket and gently pry out the fuse holder. Remove the bad fuse and
replace with a new one. The fuse holder has a built-in socket for a
spare fuse be sure not to confuse the spare fuse with active fuse.
Mega Bar 50RGB RC Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
RGB Full On
1. Quiet or high pitched sounds will not activate the unit.
If problems are not resolved; Contact American DJ® for service.
1-800-322-6337
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 18©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 17
Mega Bar 50RGB RC Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specic warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modied in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specied above, American DJ, Inc. will replace defective
parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service
and repair labor by reason of defects in material or workmanship. The sole responsibility of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of American DJ. All products covered by this warranty were
manufactured after January 1, 1990, and bear identifying marks to that effect.
E. American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all
implied warranties made by American DJ, Inc. in connection with this product, including warranties
of merchantability or tness, are limited in duration to the warranty period set forth above. And no
warranties, whether expressed or implied, including warranties of merchantability or tness, shall
apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy
shall be such repair or replacement as is expressly provided above; and under no circumstances
shall American DJ, Inc. be liable for any loss or damage, direct or consequential, arising out of the
use of, or inability to use, this product.
This warranty is the only written warranty applicable to American DJ and American Audio
Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Ampliers)
• All American Audio V-Plus Series Ampliers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which have
a 1-year (365 day Limited Warranty)
©American DJ® - www.americandj.com - Mega Bar 50RGB RC Instruction Manual Page 19
Mega Bar 50RGB RC Specifications
Model:
Mega Bar 50RGB RC
SPECIFICATIONS:
Working Position: Any safe working position
Voltage: 90V ~ 240V, 50/60Hz
LEDs: 125 x 10mm LEDs (24 Red, 54
Green, 47 Blue)
Power Cord Daisy Chain: 66 Fixtures Max.
Power Draw: 18W
Beam Angle: 40 Degree
Fuse: 1Amp
Weight: 3.3lbs./ 1.5Kgs.
Dimensions: 22” (L) x 2.5” (W) x 4” (H)
560 (L) x 63 (W) x 10 (H) mm
Colors: RGB Color Mixing
DMX Channels: 1, 2, 3, 4, 5, 6, or 7 DMX Channels
Warranty: 3 Year (1095 days)
Auto Sensing Voltage: This xture contains a electronic ballast, which will auto sense the voltage when it is plugged into the
power source.
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: info@americandj.com
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
service@americandj.eu / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...