American DJ Max User Manual

American DJ®

User

Instructions

Thank you for purchasing this American DJ® product. Some setup required.

Please read the following instructions before installing or using your new unit.

HALOGEN LAMP WARNING!

This fixture is fitted with a halogen lamp which is highly susceptible to damage if improperly handled. Never touch lamp with bare fingers as the oil from your hands will shorten lamp life. Also, never move fixture until lamp has had ample time to cool. Remember, lamps are not covered under warranty conditions.

Voltage: 120V 50/60 Hz Dimensions: 12” x 7” x 7” Lamp: ZB-ELC 250W 24V Weight: 22 lbs. Fuse: Dual 6.3A

™

THE MAX™ Feature s

•20 Dichroic Colors + White / Split colors

•21 Gobos plus Spot on separate wheel

•360 degree rotation of Yoke and Base

•High speed Shutter

•Strobes in every Color

•16 flashes per second

•Variable Speeds

•Pan 120 rpm (20,000 steps)

•Tilt 60 rpm (38,400 steps)

•DMX-512 Protocol

The MAX™ User Instructions page 1

1 2 3

1: MIC SENSITIVITY ADJUSTMENT 2: MICROPHONE 3: DMX / MASTER SLAVE SETTINGS 4: DMX INPUT / OUTPUT 5: POWER SWITCH 6: FUSE HOLDER Dual 6.3A 7: POWER CONNECTION

THE MAX™ Specifications

Control Panel

4 5 7

Precautions:

1. Never operate unit when case is open.

2. Never cover unit as this may block air vents and cause overheating and possible fire hazard.

3. Never operate unit in the rain or in damp moist conditions as this could cause electric shock.

4. Follow standard electrical safety precautions when installing, operating or servicing the unit to prevent electrical shock, fire, or equipment damage.

5.Make sure head and yoke rotate freely

6.These units are for commercial use and contain no user-serviceable parts inside.

Servicing must be conducted by qualified service personnel.

Getting Start e d

Section 1

Lamp Replacement:

Remove knurled knob on top of unit. Remove top cover. Remove and replace lamp.

Make sure to clean fan

openings, air channels an fan

gratings at regular intervals

Inspection

Every MAX™ projector has been thoroughly tested and shipped in perfect condition. Carefully unpack the projector and remove the bag with components from the carton. Inspect equipment for shipping damage.

Packing list:

1. The Max™ Projector

2. IEC power cord

3. Operating manual

4. MC-10 XLR female to male 10’ cable

Caution:

ALWAYS LIFT AND MOVE THE UNIT BY ITS BASE AND NEVER BY THE YOKE OR HEAD!

Projector Installation

1. Unit can be hung or placed in any position.

2. Make sure to use a minimum 35Kg rated clamp,and are mounted securely and safety wire is used

3. Allow enough space on all sides for proper cooling.

4. Connect IEC power cord to side of unit.(7)

5. Plug cord into properly grounded socket.

*Check that the voltage marked on the back of unit is correct for your area.

6. Set the DMX ADDRESS (3) on control panel to desired settings (ie. Sound controlled and or master / slave, DMX address). Refer to side panel for settings.

7. Turn on power switch, lamp will light and unit will make a clicking noise and reset and wait for signal from controller

*The shutter is closed in stand-by mode, so it will be difficult to tell if the lamp is lit without a

controller.

8. If stand-alone mode is chosen (10,1 on), unit will start a pre-programmed show any other units

connected to this will sync with the master unit.

9. If Stand-alone mode with sound activation is chosen (10 on), unit will wait for sound to start

a pre-programmed show and will operate as long as it senses sound.

* Unit may smoke for a few minutes until dust and excess paint is burned off by the lamp.

+ 3 hidden pages