American DJ Inno Pocket Spot User Manual

Inno Pocket Spot Specifications

Model: Inno Pocket Spot

Voltage: 100 - 240V, 50/60Hz
LED: 1 x 12W White LED
Power Consumption: 26W @ 120V

27W @ 230V
Dimensions: 6.25”(L) x 5.75”(W) x 10.5”(H)
159mm x 147mm x 265mm

Weight: 7 Lbs. / 3 kgs.
Beam Angle: 13 Degrees
Fuse: 2 Amp
Duty Cycle: None
DMX: 2 DMX Channel Modes: 9 Channel

Mode & 11 Channel Mode

Colors: 7 + White
Gobos: 7 + Spot
Sound Active: Yes
Working Position: Any Safe, Secure Position
Warranty: 2 Year (730 days)

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any
prior written notice.

INNO POCKET SPOT

Auto Sensing Voltage: This xture contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged
into the power source.

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] / Fax: [phone]

Web: www.adj.com / E-mail: [e-mail]

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.adj.eu

Tel: [phone] / Fax: [phone]

User Instructions

Rev. 3/14

©2013 ADJ Products, LLC all rights reserved. Information,

specications, diagrams, images, and instructions herein are

subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.

ADJ Products, LLC and all aliated companies hereby dis-
claim any and all liabilities for property, equipment, building,
and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of
any information contained within this document, and/or as a
result of the improper, unsafe, unsucient and negligent as­sembly, installation, rigging, and operation of this product.

Inno Pocket Spot Warranty

MANUFACTURER’S LIMITED WARRANTY

A. A DJ Products, LLC her eby wa rrants, to the or igi nal pu rchaser, ADJ Pro duc ts, LL C products
to be free of manufa cturing defect s in mater ial and workma nship for a presc ribed p eriod from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
pr odu ct i s p ur ch ased wi th in th e Uni te d Sta te s of A me ric a, i ncl ud in g p os se ssion s and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.

C

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back
the product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the pro-

duct only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested
repairs or service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC
will pay return shipping charges only to a designated point within the United States. If the entire instru­ ment is sent, it must be shipped in it’s original package. No accessories should be shipped with the product.
If any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.

Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.

Please turn o all electrical products when they are not in use. To

avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!

E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.

No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer ’s and/or Dealer ’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.

T his w arran ty is the only writt en wa rrant y app licab le to ADJ P roduc ts, L LC Pr oduct s and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

 •LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent

Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LEDs and lamps)

 •LaserProducts=90-DayLimitedWarranty
 •L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power

supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty).

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 26

Inno Pocket Spot Fuse Replacement

Inno Pocket Spot General Information

Locate and remove the unit’s power cord. Once the cord has been
removed located the fuse holder located inside the power socket.
Insert a flat-head screw driver into the power socket and gently pry
out the fuse holder. Remove the bad fuse and replace with a new one.
The fuse holder has a built-in socket for a spare fuse be sure not to
confuse the spare fuse with active fuse.

Inno Pocket Spot Cleaning

Due to fog residue, smoke, and dust cleaning the internal and exter­nal optical lenses and mirror should be carried out periodically to
optimize light output. Cleaning frequency depends on the environ­ment in which the fixture operates (I.e. smoke, fog residue, dust,
dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the out­ side casing.

2. Use a brush to wipe down the cooling vents and fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every
20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every
30-60 days.

5. Always be sure to dry all parts completely before plugging the unit
back in.

Inno Pocket Spot Trouble Shooting

Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.

Unpacking: Thank you for purchasing the Inno Pocket Spot by ADJ

Products, LLC. Every Inno Pocket Spot has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.

If the carton appears to be damaged, carefully inspect your xture for

any damage and be sure all equipment necessary to operate the unit
has arrived intact. In the event damage has been found or parts are
missing, please contact our toll free customer support number for fur­ther instructions. Please do not return this unit to your dealer without

contacting customer support rst.

Introduction: The Inno Pocket Spot is a DMX intelligent, moving

head, mini LED fixture. The Inno Pocket Spot can operate as a stand
alone fixture or in a Master/Slave configuration. The Inno Pocket Spot
has three operating modes; a sound active, show mode, DMX con­trolled. This fixture is suitable for theaters, studios, retail stores, and
other similar locations. For best results use fog or special effects smoke

to enhance the beams projections.

Customer Support: ADJ Products, LLC provides a toll free cus-

tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.adj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: [phone]
Fax: [phone]
E-mail: [e-mail]

No light output from the unit;

1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.

2. Be sure the fuse holder is completely and properly seated.

Unit does not respond to sound;

1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 25

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 2

Inno Pocket Spot General Instructions

To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.

Inno Pocket Spot Features

• DMX-512 Protocol Compatible (9 DMX Channels or 11 Channels)

• 7 Colors + White

• Fixed Gobo Wheel with 7 Gobos + Spot

• 3 Operating Modes - Sound Active, Show Mode, & DMX Control

• Internal Microphone

• Digital Display for Address and Function Setting

• 4 Preprogrammed Shows

• UC-IR Compatiable (Not Included)

Inno Pocket Spot Warranty Registration

The Inno Pocket Spot carries a 2 year (730 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase
and warranty. You may also register your product online at www. adj­products.com. All returned service items whether under warranty or
not, must be freight pre-paid and accompany a return authorization
(R.A.) number. If the unit is under warranty you must provide a copy
of your proof of purchase invoice. Please contact ADJ Products, LLC
customer support for a R.A. number.

Inno Pocket Spot Handling Precautions

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact ADJ Products, LLC.

Inno Pocket Spot Photometric Chart

0m( )

6.0

Dis tance (m)

13

0

1.0 2.0 3.0 4.0

5.0

Inno Pocket Spot Dimmer Curve Chart

Ramp Effect

Standard

Stage

TV

Architectural

Theatre

(Fade Time) (Fade Time)

During operation the housing may become extremely hot. Avoid
touching the unit with bare hands while in use.

ADJ Products, LLC will not accept any liability for any resulting dam­ages caused by the non-observance of this manual or any unauthor­ized modication to this unit.

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 3

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 24

Inno Pocket Spot 11 Channel Mode

Inno Pocket Spot Safety Precautions

Channel Value Function

6 190 - 193 STOP

194 - 255 GOBO SCROLL SLOW - FAST

7 SHUTTER/STROBE
0 - 7 BLACKOUT
8 - 15 SHUTTER OPEN

16 - 131 STROBING SLOW - FAST

132 - 139 SHUTTER OPEN
140 - 181 SHUTTER SLOW OPEN - FAST CLOSE
182 - 189 SHUTTER OPEN
190 - 231 SHUTTER FAST OPEN - SLOW CLOSE
232 - 239 SHUTTER OPEN
240 - 247 RANDOM STROBE
248 - 255 SHUTTER OPEN
8 0 - 255 DIMMER 0% - 100%
9 0 - 255 MOVEMENT SPEED FAST - SLOW
10 FUNCTION
1 - 69 NO FUNCTION
70 - 79 BLACKOUT WITH PAN/TILT
80 - 89 NO BLACKOUT WITH PAN/TILT

90 - 99 BLACKOUT WITH COLOR CHANGE
100 - 109 NO BLACKOUT WITH COLOR CHANGE
110 - 119 BLACKOUT WITH GOBO CHANGE
120 - 129 NO BLACKOUT WITH GOBO CHANGE

130 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 249 NO FUNCTION
250 - 255 SOUND ACTIVE MODE
11 DIMMER CURVES
0 - 41 STANDARD

42 - 84 STAGE

85 - 127 TV
128 - 170 ARCHITECTURAL
171 - 213 THEATER

214 - 255 DEFAULT TO UNIT CURVE SETTING

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break o the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep­ tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 25 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits
a marked change in performance.

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 4ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 23

Inno Pocket Spot Mounting

Inno Pocket Spot 11 Channel Mode

When installing the unit, the trussing or area of installation must be
able to hold 10 times the weight without any deformation. When
installing the unit must be secured with a secondary safety attach­ment, e.g. and appropriate safety cable. Never stand directly below
the unit when mounting, removing, or servicing the unit.

Overhead mounting requires extensive experience, including calculat­ing working load limits, installation material being used, and perodic
safety inspection of all installation material and unit. If you lack these

qualications, do not attempt the installation yourself.

The installaiton should be checked by a skilled person once a year.

The Inno Pocket Spot is fully operational in two dierent mounting
positions, hanging upside-down from a ceiling or set on a at level

surface. To avoid internal damage to the unit, never mount the unit on

its side as illustrated above. Be sure this xture is kept at least 0.5m
away from any ammable materials (decoration etc.). Always use

and install the supplied safety cable as a safety measure to prevent
accidental damage and/or injury in the event the clamp fails (see next
page).

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 5

Channel Value Function

1 0 - 255 PAN MOVEMENT 8bit

2 0 - 255 PAN FINE 16bit

3 0 - 255 TILT MOVEMENT 8bit

4 0 - 255 TILT FINE 16bit
5 COLORS
0 - 7 WHITE
8 - 14 RED

15 - 21 ORANGE

22 - 28 YELLOW

29 - 35 GREEN

36 - 42 BLUE

43 - 49 LIGHT BLUE

50 - 56 PINK
57 - 127 SPLIT COLORS
128 - 189 COLOR SCROLL FAST - SLOW
190 - 193 STOP
194 - 255 COLOR SCROLL SLOW - FAST

6 GOBO WHEEL

0 - 7 OPEN

8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7

64 - 71 OPEN SHAKE

72 - 79 GOBO 1 SHAKE
80 - 87 GOBO 2 SHAKE
88 - 95 GOBO 3 SHAKE
96 - 103 GOBO 4 SHAKE
104 - 111 GOBO 5 SHAKE
112 - 119 GOBO 6 SHAKE
120 - 127 GOBO 7 SHAKE
128 - 189 GOBO SCROLL FAST - SLOW

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 22

Inno Pocket Spot Mounting Inno Pocket Spot 9 Channel Mode

Channel Value Function

5 SHUTTER/STROBE

0 - 7 BLACKOUT
8 - 15 SHUTTER OPEN

16 - 131 STROBING SLOW - FAST

132 - 139 SHUTTER OPEN
140 - 181 SHUTTER SLOW OPEN - FAST CLOSE
182 - 189 SHUTTER OPEN
190 - 231 SHUTTER FAST OPEN - SLOW CLOSE
232 - 239 SHUTTER OPEN
240 - 247 RANDOM STROBE
248 - 255 SHUTTER OPEN
6 0 - 255 DIMMER 0% - 100%
7 0 - 255 MOVEMENT SPEED FAST - SLOW
8 FUNCTION
0 - 69 NO FUNCTION
70 - 79 BLACKOUT WITH PAN/TILT
80 - 89 NO FUNCTION

90 - 99 BLACKOUT WITH COLOR CHANGE

100 - 109 NO FUNCTION

110 - 119 BLACKOUT WITH GOBO CHANGE

120 - 199 NO FUNCTION
200 - 209 RESET ALL
210 - 249 NO FUNCTION
250 - 255 SOUND ACTIVE MODE

9 DIMMER CURVES
0 - 41 STANDARD

42 - 84 STAGE

85 - 127 TV
128 - 170 ARCHITECTURAL
171 - 213 THEATER

214 - 255 DEFAULT TO UNIT CURVE SETTING

NOTICE: The suitable enviromental temperature for this light-

ing xture is between -25˚ C to 45˚ C. Do not place this lighting
xture in an enviroment where the temperatures are under or
above the temperatures stated above. This will allow the xture
to run at its best and help prolong the xture life.

Screw one clamp via a M12 screw and nut to the included
bracket. Attach the bracket using the included screws to the
bottom of the Inno Pocket Spot. Attach the eyehole screw to
the bottom of the base and pull the safety-cable through the

screw and over the trussing system or a safe xation spot.

Insert the end in the carabine and tighten the safety screw.

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 21

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 6

Inno Pocket Spot DMX Set Up

Inno Pocket Spot 9 Channel Mode

Power Supply: The ADJ Inno Pocket Spot contains a automatic volt-

age switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix­ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models

of dierent manufactures to be linked together and operate from a
single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The Inno Pocket Spot can be controlled via DMX-512 pro-

tocol. The Inno Pocket Spot two DMX channel modes; 9 channel mode
& 11 channel mode. The DMX address is set elec­tronically using the controls on the front panel of
the unit. Your unit and your DMX controller require
a approved DMX-512 110 Ohm Data cable for data
input and data output (Figure 1). We recommend
Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm
shielded cable (This cable may be purchased at
almost all professional sound and lighting stores).

Figure 1

Channel Value Function

1 0 - 255 PAN MOVEMENT 8bit

2 0 - 255 TILT MOVEMENT 8bit

3 COLORS
0 - 7 WHITE
8 - 14 RED

15 - 21 ORANGE

22 - 28 YELLOW

29 - 35 GREEN

36 - 42 BLUE

43 - 49 LIGHT BLUE

50 - 56 PINK
57 - 127 SPLIT COLORS
128 - 189 COLOR SCROLL FAST - SLOW
190 - 193 STOP
194 - 255 COLOR SCROLL SLOW - FAST

4 GOBO WHEEL

0 - 7 OPEN

8 - 15 GOBO 1
16 - 23 GOBO 2
24 - 31 GOBO 3
32 - 39 GOBO 4
40 - 47 GOBO 5
48 - 55 GOBO 6
56 - 63 GOBO 7

64 - 71 OPEN SHAKE

72 - 79 GOBO 1 SHAKE
80 - 87 GOBO 2 SHAKE
88 - 95 GOBO 3 SHAKE
96 - 103 GOBO 4 SHAKE
104 - 111 GOBO 5 SHAKE
112 - 119 GOBO 6 SHAKE
120 - 127 GOBO 7 SHAKE
128 - 189 GOBO SCROLL FAST - SLOW

190 - 193 STOP

194 - 255 GOBO SCROLL SLOW - FAST

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 7

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 20

Inno Pocket Spot Remote Operation

Inno Pocket Spot DMX Set Up

The UC-IR infrared remote gives you control of various functions
(See below). To control the fixture you must aim the remote at the

front of the fixture and be no more then 30 feet away.

STAND BY - Pressing this button will blackout the fixture.

FULL ON - Hold this button down to fully light up the unit. When you

let the button go, the unit will return to its previous state.

FADE/GOBO - Press this button to enter Gobo mode. Use the 1-9
buttons to select your desired gobo. Adjust the output intensity using
the “DIMMER +” and “DIMMER -” buttons.

“DIMMER +” and “DIMMER -” - Use these buttons to adjust the out­put intensity and to adjust the strobe speed.

STROBE - This button will activate the strobe effect. You can control
the flash rate by pressing the “DIMMER +” and “DIMMER -” buttons.
If you press and hold this button the unit will begin to strobe.

COLOR - Press this button to enter Dimmer mode. Use the 1-9 but­tons to select your desired color. Adjust the output intensity using the
“DIMMER +” and “DIMMER -” buttons.

1-9 - When in either Gobo mode or Color mode, these buttons will
allow you to select either a gobo or color.

Your cables should be made with a male and female XLR connector on
either end of the cable. Also remember that DMX cable must be daisy
chained and cannot be split.

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con­nect the cable’s shield conductor to the ground lug or allow the shield

conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

COMMON

XLR Male Socket

1 Ground

Figure 3

DMX512 OUT

3-PIN XLR

2 Cold

3 Hot

1

3

2

XLR Female Socket

2 Cold

DMX +

DMX -

1 Ground

3 Hot

1

DMX512 IN

3

3-PIN XLR

2

Figure 2

XLR Pin Conguration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

SOUND ON & OFF - These buttons activate and deactivate the
sound active mode.

SHOW - This activates the show mode. Use the “DIMMER +” and
“DIMMER -” buttons to scroll through the 4 shows.

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 19

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.

Terminatio n reduces signal errors and

1

avo ids sig nal tra nsmi ssion problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DM X +) of the la st fixture.

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 8

Figure 4

Inno Pocket Spot DMX Set Up

Inno Pocket Spot Master-Slave Set Up

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting stan­dard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

Pin 1

Pin 2

Pin 3

Pin 1

Pin 2

Pin 3

Pin 4 - Do Not Use

Pin 5 - Do Not Use

Master-Slave Operation This function will allow you to link up to 16

units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-
er via the XLR connector on the rear of the units. Remember the
Male XLR connector is the input and the Female XLR connector

is the output. The rst unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male
XLR connector only. For longer cable runs we suggest a termina­ tor at the last fixture.

2. On the Master unit press the MENU button until “SLND” is dis­ played, and press ENTER. Use the UP and DOWN buttons to
scroll to the “MAST” setting and press ENTER.

3. After setting the Master unit to the master setting find your
desired operating mode.

4. On the slave units press the MENU button until “SLND” is dis­ played, and press ENTER. Choose either “SL 1” or “SL 2” and
press ENTER. See page 10 for more info.

5. The slave units will now follow the Master unit.

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 9

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 18

Inno Pocket Spot Operation

Sho w Mo de

Sla ve M ode

Los t DM X Sig nal

LED Display

Di splay No rma l

Di splay In ver sio n

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.

1. The Inno Pocket Spot has 2 DMX channel modes; 9 channel
mode or 11 channel mode. See pages 20-23 for detailed descrip­ tion of the DMX values and traits.

2. To control your fixture in DMX mode, follow the set-up procedures
on pages 5-7 as well as the set-up specifications that are includ­ ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instruction on page 9 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.

7. For help operating in DMX mode consult the manual included
with your DMX controller.

Sound Active Mode: This mode allows either single unit or several

units linked together, to run to the beat of the music.

1. Press the MENU button until “SOUN” is displayed, and press
ENTER. Press the UP or DOWN buttons so that “ON” is dis-
played and press ENTER.

2. Press the MENU button until “SENS” is displayed, and press
ENTER. Use the UP and DOWN buttons to adjust the sound
sensitivity. Press ENTER when you have found your desired sensi­ tivity level.

Show Mode: This mode allows either a single unit or several units

linked together, to run one of four shows that you choose.

1. Press the MENU button until “SHND” is displayed, and press
ENTER.

2. Press the UP or DOWN buttons until you nd your desired show,

and press ENTER.

Inno Pocket Spot System Menu

DMX 512 Add res s Set ting

Cha nne l Mod e

Dim mer Mode

Sou nd Mo de

Sou nd S ense

Pan Inve rse

Til t Inv ers e

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 17

Aut o Test

Fi xtu re Us e Time

Fi rmw are Version

Res et

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 10

Inno Pocket Spot System Menu

Inno Pocket Spot Home Adjustment Menu

System Menu: When making adjustments press ENTER to

conrm your setup then press and hold the MENU button

for at least 3 seconds. To exit without making any adjust­ments press the MENU button. The display will lock after 30
seconds, press the MENU button for 3 seconds to unlock.

ADDR - DMX Address Setting.

1. Press the either the MENU, UP, or DOWN buttons until “ADDR” is
displayed, press ENTER.

2. The current address will now be displayed and ashing. Press the
UP or DOWN buttons to nd your desired address. Press ENTER to

set your desired DMX address.

CHND - This will let select your desired DMX channel

mode.

1. Press the either the MENU button until “CHND” is displayed, press
ENTER. Either “9CH” or “11CH” will be displayed

2. Press the UP or DOWN buttons to nd your desired DMX channel
mode and press ENTER to conm and exit.

SHND - Show modes 0-4 (Factory programs). Show

mode can run with or without sound active mode active.

OTIL - Adjustment of the tilt position.

1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OTIL” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

OGOB - Adjustment of the gobo wheel.

1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OGOB” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

OCOL - Adjustment for the color wheel.

1. Press the ENTER button for at least 3 seconds, then press the UP
or DOWN buttons so that “OCOL” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

1. Press the MENU button until “SHND” is displayed, press ENTER.

2. “Sh X” will now be displayed, “X” representing a number between
0-4. Shows 1-4 are factory programs, while show “0” is random mode.

Use the UP or DOWN buttons to nd your desired show.

3. When you have found your desired show press ENTER, then press
and hold the MENU button for at least 3 seconds to activate. After
you have set your desired show, it can be changed at any time using

the UP or DOWN buttons.

DIND - This will let select your desired dimmer curve.

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 11

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 16

Inno Pocket Spot System Menu

Inno Pocket Spot System Menu

the unit.

1. Press the either the MENU button until “VER” is displayed, press
ENTER.

2. The display will show the software version.

RSET - Use this function to reset the unit.

1. Press the MENU button until “RSET” is displayed, press ENTER.

2. The xture will now reset.

Inno Pocket Spot Home Adjustment Menu

To enter the home position adjustment menu, press the ENTER
button for at least 5 seconds. In this submenu you are able to adjust
the original position of the pan position, tilt position, color wheel posi­tion, and gobo wheel position.

OPAN - Adjustment of the pan position.

1. Press the ENTER button for at least 5 seconds, then press the UP
or DOWN buttons so that “OPAN” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and

then press ENTER to conrm. Press the MENU button for one second

to exit.

1. Press the either the MENU button until “DIND” is displayed, press
ENTER. 1 of 5 dimmer curves will be displayed. “STDA” (standard),
“STGE” (stage), “TV” (TV), “ARAL” (theatrical), or “THAL” (Architec­tural).

2. Press the UP or DOWN buttons to nd your desired dimmer curve
and press ENTER to conm and exit.

SLND - This will let you set unit as a master or slave in a

master/slave conguration.

1. Press the MENU button until “SLND” is displayed, press ENTER.
Either “MAST”, “SL 1”, or “SL 2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is dis-

played, press ENTER to conm.

NOTE: In a Master/Slave conguration you can set one xture to
Master and then set the next xture to “SL 2”, the xtures will now

have contrast movement to each other.

LOST - This mode can be used as a precaution mode, that

in case the DMX signal is lost, interrupted, or power is lost,
the operating mode chosen in the setup is the running mode

the xture will go into when the DMX signal is lost. You can

also set this as the operating mode you would like the unit to

return to when power is applied.

1. Press the MENU button until “LOST” is displayed, and either
“HOLD”, “SHND”, or “BLAC” will be displayed beneath.

2. Press ENTER and the bottom choice will begin to ash. Use the UP

or DOWN buttons to choose an operating mode you would like the unit
to start up in when power is applied or the DMX signal is lost.

• Hold - If the DMX signal is lost the xture will stay in the last DMX set­ting. If power is applied and this mode is set, the unit will automatically
go into the last DMX set up.

• SHND (Show Mode) - If the DMX signal is lost, interrupted, the unit

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 15

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 12

Inno Pocket Spot System Menu

Inno Pocket Spot System Menu

will automatically go into show mode.

• BLAC (Blackout) - If the DMX signal is lost or interrupted, the unit will

automatically go into stand by mode.

3. Press ENTER to conrm your desired set up.

SOUN - Sound Active mode.

1. Press the MENU button until “SOUN” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode, or
“OFF” to deactivate sound active mode.

3. Press ENTER to conrm.

SENS - In this mode you can adjust the sound sensitiv-

ity.

1. Press the MENU button until “SENS” is displayed, press ENTER.

2. A number between 0-100 will be displayed. Press the UP or DOWN
buttons to adjust the sound sensitivity. 0 being the least sensitive,
and 100 being the most sensitive.

2. To activate the tilt inversion press the UP or DOWN buttons until
“Yes” is displayed, press ENTER to conm. To deactivate tilt inver-
sion, select “No” and press Enter.

LED - With this function you can have the LED display

turn off after 10 seconds.

1. Press the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at all
times, or “OFF” to switch to have the LED display switch o after 10
seconds.

3. Press ENTER to conrm. To make you LED display reappear again

press any button.

DISP - This function will reverse the display 180º.

1. Press the MENU button until “DISP” is displayed, press ENTER.

2. Press ENTER to “ip” the display. Press ENTER to “ip” it again.

Press ENTER when you have made your desired setup.

3. When you have found your desired setting press ENTER to conrm.

PINT - Pan Inversion

1. Press the MENU button until “PINT” is displayed, press ENTER.
Either “Yes” or “No” will be displayed.

2. To activate the Pan inversion press the UP or DOWN buttons until
“Yes” is displayed, press ENTER to conm. To deactivate Pan inver-
sion, select “No” and press Enter.

TINT - Tilt Inversion

1. Press the MENU button until “TINT” is displayed, press ENTER.
Either “Yes” or “No” will be displayed.

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 13

TEST - This function will run a self test program.

1. Press the MENU button until “TEST” is displayed, press ENTER.

2. The xture will now run a self test.

FHRS - With this function you can display the running

time of the unit.

1. Press the MENU button until “FHRS” is displayed, press ENTER.

2. The running time of the xture will now be displayed. Press MENU

to exit.

VER - Use this function to display the Software version of

ADJ Products, LLC - www.adj.com - Inno Pocket Spot Instruction Manual Page 14