American DJ Emrald Beam User Manual

Rev 10/01

User Instructions

Los Angeles, CA. 90058

www.americandj.com

American DJ®

4295 Charter Street

American DJ®

not expose this unit to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact

your nearest American DJ dealer.

PLEASE do not discard the shipping carton in the trash. Please

recycle when ever possible.

©American DJ® - www.americandj.com - Emerald Beam™ Instruction Manual Page 2

E-mail: [e-mail]

Warning! To prevent or reduce the risk of electrical shock or fi re, do

can DJ®. Service Hours are Monday through Friday 9:00 a.m. to 5:00

p.m. Pacifi c Standard Time.

Voice: [phone]

Fax: [phone]

ments or suggestions. For service related issue please contact Ameri-

ther instructions. Please do not return the unit to your dealer without

fi rst contacting customer support.

damage and be sure all accessories necessary to operate the system

have arrived intact. In the event damage has been found or parts are

missing, please contact our toll free customer support number for fur-

Customer Support: American DJ® provides a toll free customer sup-

port line, to provide set up help and to answer any question should

you encounter problems during your set up or initial operation. You

may also visit us on the web at www.americandj.com for any com-

Beam.

If the carton appears to be damaged, carefully inspect the unit for any

the unit. The unit may be mounted in either a horizontal or vertical posi-

tion.

the laser refl ection over a wide area. This unit has a sound-active mode

that allows the unit to refl ect on all eight mirrors. The unit’s sound sen-

sitivity may be adjusted by a sensitivity adjustment on the bottom of

Unpacking: Every Emerald Beam™ has been thoroughly tested and

has been shipped in perfect operating condition. Carefully check the

shipping carton for damage that may have occurred during shipping.

Introduction: Thank you for purchasing the American DJ® Emerald

ates different patterns. The unit uses eight internal mirrors to bounce

™

The Emerald Beam™ is a unique green laser effect that cre-

Emerald Beam™ General Introduction

checking the fuse, be sure to check the fuse that has the metal ends

completely exposed.

flat head screw drive to pry out the fuse holder. When the fuse holder

is exposed remove the old fuse and replace it with a similar one. The

fuse holder comes with a slot for a spare fuse. When replacing and

Fuse Replacement: Disconnect the unit’s main power supply. Use a

for servicing. Continuing to use the unit may cause serious damage.

customer support for further instructions, you may have to return the unit

Warning: If you continue to blow fuses, STOP using the unit. Contact

will void your manufactures warranty.

erwise specified by an authorized American DJ® technician. Replace

with anything other than the specified part can damage your unit and

Caution: Always replace with the exact same type fuse, unless oth-

number.

Emerald Beam™ Fuse Replacement

invoice. Please contact American DJ

® customer support for a R.A.

and accompany a return authorization (R.A.) number. If the unit is

under warranty you must provide a copy of your proof of purchase

The Emerald Beam™ carries a 90 day limited warranty. Please fill

out the enclosed warranty card to validate your purchase. All returned

service items whether under warranty or not, must be freight pre-paid

Emerald Beam™ Warranty Registration

• Fan Cooled

• 16 Programs

• Music Sensitivity Knob

• 4.9mW Green Laser Diode

• Built-In Hanging Yoke

• Sound Active with Internal Microphone

Emerald Beam™ Features

erence.

Emerald Beam™ General Instructions Emerald Beam™ Safety Precautions

Please carefully read and understand the instructions in this manual

thoroughly before attempting to operate this unit. These instructions

contain important safety information regarding the use and mainte-

nance of this unit. Please keep this manual with the unit, for future ref-

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and fi re in case of an internal short. Do not attempt to operate

this unit if the power cord has been frayed or broken.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never plug this unit in to a dimmer pack.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product outdoors

voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power cords should be routed so they are not likely to be walked on,

pinched by items placed upon or against them.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 6 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances

(including amplifiers) that produce heat.

©American DJ® - www.americandj.com - Emerald Beam™ Instruction Manual Page 4©American DJ® - www.americandj.com - Emerald Beam™ Instruction Manual Page 3

Safety Issues: This unit may blow a fuse if the maximum allotted

load of 2 amps (1 amp 220v) is reached. If the fuse needs replacement,

always replace the fuse with same exact type that was remove, unless

otherwise instructed by an authorized American DJ

cian. Use of a different type fuse from that which is recommended may

cause fire or electric shock and will void the manufactures warranty.

• To reduce the risk of electrical shock or fi re, do not expose this unit

rain or moisture.

DANGER

VISIBLE LASER RADIATION

-AVOID DIRECT EYE EXPOSURE

LASER DIODE

WAVELENGTH : 532 nm

Max Output : <4.9mW

Class IIIa Laser Product

® service techni-