
HHA
HHA
HHAHHA
ADAPTER FOR SHURE MOUNT TYPE HANDHELD WIRELESS TRANSMITTERS
ADAPTER FOR SHURE MOUNT TYPE HANDHELD WIRELESS TRANSMITTERS
ADAPTER FOR SHURE MOUNT TYPE HANDHELD WIRELESS TRANSMITTERSADAPTER FOR SHURE MOUNT TYPE HANDHELD WIRELESS TRANSMITTERS
The HHA adapter serves to mount Sennheiser® 5000 series compatible
capsules on to any wireless handheld transmitter with a Shure® mount.
In addition to the black cover ring shipped, colored rings are available
to distinguish microphones.
Use:
we recommend to screw on the microphone head first. Carefully line up the
head, push down and screw the head on the adapter. Slide the cover ring
over the HHA from lower end.
Then screw the assembly on to the handheld wireless.
Switchable Bias voltage:
default setting is 7 Volts.
To profit from the full dynamic range of the true condenser Neumann® capsules, the voltage
converter in the HHA can be switched to provide 15 Volts Bias.
Only do this when using the KK104 / KK105 condenser capsules
Only do this when using the KK104 / KK105 condenser capsules, there is no use of higher voltage
Only do this when using the KK104 / KK105 condenser capsulesOnly do this when using the KK104 / KK105 condenser capsules
with ME electret or MD dynamic capsules, and damaging those, while not probable, can not be
excluded.
The High Bias 15 Volts setting only works with handheld wireless that provide enough current,
tested with Lectrosonics® HH.
The Shure ULX series will not work with this setting. Other manufacturers to be tested.
Set the appropriate Bias voltage before mounting the microphone
capsule.
There is a small slide switch in the center of the plastic body on the top
side.
It can be accessed with a pin or small screwdriver.
15 to left activates 15 Volts Bias voltage.
7 to right activates 7 Volts Bias voltage
Ambient Recording GmbH Schleissheimer Strasse 181c Tel.: +49 89 3605510-0
D – 80797 Munich Fax: +49 89 651855
info@ambient.de
www.ambient.de

Part numbers:
HHA
HHA-B adapter body with step-up converter
HHA-R-N anodized aluminum ring BLACK for Lectrosonics’ HH
HHA-R-N
HHA-R-Y
HHA-R-R
HHA-R-G
HHA-R-B
adapter set consisting of:
anodized aluminum ring BLACK for Lectrosonics’ HH
anodized aluminum ring YELLLOW for Lectrosonics’ HH
anodized aluminum ring RED for Lectrosonics’ HH
anodized aluminum ring GREEN for Lectrosonics’ HH
anodized aluminum ring BLUE for Lectrosonics’ HH
HHA-S
HHA-B adapter body with step-up converter
HHA-RS-N anodized aluminum ring BLACK for Shure
HHA-RS-N
HHA-RS-Y
HHA-RS-R
HHA-RS-G
HHA-RS-B
adapter set consisting of:
anodized aluminum ring BLACK for Shure
anodized aluminum ring YELLLOW for Shure
anodized aluminum ring RED for Shure
anodized aluminum ring GREEN for Shure
anodized aluminum ring BLUE for Shure
The compatible capsules are:
Sennheiser® ME 5xxx capsules
Sennheiser® MD 5xxx capsules
Neumann® KK 104 and KK105 capsules
Specifications:
weight 34g (HHA-B : 32g, HHA-Rx: 2g)
length added to system: 9mm
outer diameter with cover ring: 36 MM (HHA-Rx), 37mm (HHA-RSx)
Bias voltage switchable: 7 Volts DC / 15 Volts DC
Lectrosonics, Neumann, Sennheiser, Shure are registered trademarks of their respective owner.
Ambient Recording GmbH Schleissheimer Strasse 181c Tel.: +49 89 3605510-0
D – 80797 Munich Fax: +49 89 651855
info@ambient.de
www.ambient.de