Amana UXL6048YSS Owners Manual

36" (91.4 CM) AND 48" (121.9 CM) HOOD LINER

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301

or visit our website at www.whirlpool.com

In Canada, call 1-800-807-6777 or visit our website at www.whirlpool.ca

CAISSE DE HOTTE

36" (91,4 CM) ET 48" (121,9 CM)

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composer

le 1-800-807-6777 ou visiter notre site Web à

Table of Contents/Table des matières.............................................................................2

www.whirlpool.ca

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. FOR RESIDENTIAL USE ONLY. IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

LI3ZIB/W10331011B

TABLE OF CONTENTS

TABLE DES MATIÈRES

RANGE HOOD SAFETY .................................................................2

INSTALLATION REQUIREMENTS................................................4

Tools and Parts ............................................................................4

Location Requirements................................................................ 4

Venting Requirements..................................................................5

Electrical Requirements ...............................................................6

INSTALLATION INSTRUCTIONS..................................................7

Prepare Location..........................................................................7

Install Hood Liner Internal Blower Motor .....................................8

Install Hood Liner In-Line

(External Type) Blower Motor.....................................................10

Make Electrical Connections for In-Line

Blower Motor System ................................................................11

Make Electrical Power Supply

Connection to Hood Liner..........................................................12

Complete Installation and Check Operation..............................13

RANGE HOOD USE......................................................................14

Range Hood Controls ................................................................14

RANGE HOOD CARE...................................................................15

Cleaning......................................................................................15

WIRING DIAGRAM .......................................................................16

ASSISTANCE OR SERVICE.........................................................17

In the U.S.A. ...............................................................................17

In Canada ...................................................................................17

Accessories................................................................................17

WARRANTY ..................................................................................18

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE ...............................19

EXIGENCES D'INSTALLATION...................................................21

Outils et pièces...........................................................................21

Exigences d'emplacement.........................................................21

Exigences concernant l’évacuation ...........................................22

Spécifications électriques ..........................................................23

INSTRUCTIONS D’INSTALLATION.............................................24

Préparation de l'emplacement...................................................24

Installation du moteur du ventilateur interne

de la caisse de la hotte ..............................................................25

Installation du moteur du ventilateur

en ligne (externe) de la caisse de la hotte..................................27

Réalisation des connexions électriques

du système du moteur du ventilateur en ligne...........................28

Réalisation des connexions de l’alimentation

électrique à la caisse de la hotte................................................30

Achever l'installation et vérifier le fonctionnement ....................30

UTILISATION DE LA HOTTE .......................................................31

Commandes de la hotte de cuisinière .......................................31

ENTRETIEN DE LA HOTTE..........................................................32

Nettoyage ...................................................................................32

SCHÉMA DE CÂBLAGE...............................................................33

ASSISTANCE OU SERVICE.........................................................34

Au Canada..................................................................................34

Accessoires ................................................................................34

GARANTIE.....................................................................................35

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

can be killed or seriously injured if you don't

You instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

■ Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer.

■ Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

■ Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

■ Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for examination and/or repair.

■ Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

■ When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

■ Ducted fans must always be vented outdoors. CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into spaces within walls or ceilings, attics or into crawl spaces, or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

■ Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

■ Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

■ Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

■ Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:

■ SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

■ NEVER PICK UP A FLAMING PAN - you may be burned.

■ DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

■ Use an extinguisher ONLY if:

– You know you have a class ABC extinguisher, and you

already know how to operate it.

– The fire is small and contained in the area where it

started. – The fire department is being called. – You can fight the fire with your back to an exit.

Based on "Kitchen Fire Safety Tips" published by NFPA.

■ WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control device.

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tool s ne ed ed

■ Level

■ Drill

■ 1¼" (3 cm) drill bit

■ ¹⁄₈" (3 mm) drill bit

■ Pencil

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Pliers

■ Caulking gun and weatherproof caulking compound

■ Vent clamps

■ Jigsaw or keyhole saw

■ Flat-blade screwdriver

■ Metal snips

■ Phillips screwdriver

Parts needed

■ Home power supply cable

■ 1 - ½" (1.3 cm) UL listed or CSA approved strain relief

■ 3 UL listed wire connectors

■ 1 wall or roof cap

■ Metal vent system

■ Blower motor system - internal or external (see “Blower

Motor System” in the “Accessories” section).

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Have a qualified technician install the hood liner. It is the

installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located behind the left filter on the rear wall of the hood liner.

The hood liner location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

The hood liner must be surrounded by a custom built enclosure with hood support capable of supporting 75 lb (34 kg).

Grounded electrical outlet is required. See “Electrical Requirements” section.

All openings in ceiling and wall where canopy hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Cabinet Dimensions

36" (91.4 cm) for 36" models

48" (121.9 cm) for 48" models

Parts supplied

Remove parts from packages. Check that all parts are included.

■ 3 metal grease filters

■ Hood liner with halogen lamps installed.

■ 1 - 10" (25.4 cm) square to 10" (25.4 cm) round duct

transition with damper.

■ 4 - 5 x 45 mm mounting screws

■ 4 - 4.2 x 8 mm screws

■ T-20 TORX

†®TORX is a registered trademark of Saturn Fasteners, Inc.

®†

adapter

22" (55.9 cm)

Hood support must be capable of supporting 75 lb (34 kg)

“X“ bottom of canopy to cooking surface

Hood liner depth

IMPORTANT:

Minimum distance “X”: 24" (61 cm) from electric cooking surfaces. Minimum distance “X”: 30" (76.2 cm) from gas cooking surfaces. Suggested maximum distance “X”: 36" (91.4 cm).

Product Dimensions

12³⁄₈"

(31.4 cm)

11" (27.9 cm)

18" (45.7 cm) for 36" models 24" (61.0 cm) for 48" models

11¹⁄₂"

(29.2 cm)

(12.8 cm)

4¹³⁄₁₆" (12.2 cm)

5¹⁄₁₆"

27⁵⁄₈" (70.1 cm)

29¹³⁄₁₆" (75.8 cm)

35⁷⁄₈" (91.1 cm) for 36" models

47⁷⁄₈" (121.6 cm) for 48" models

Venting Requirements

■ Vent system must terminate to the outdoors.

■ Do not terminate the vent system in an attic or other enclosed

area.

■ Do not use 4" (10.2 cm) laundry-type wall caps.

■ Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

■ The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

■ Do not install 2 elbows together.

■ Use clamps to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening around the

cap.

■ The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize backward cold air flow and a thermal break should be installed to minimize conduction of outside temperatures as part of the vent system. The damper should be on the cold air side of the thermal break.

The break should be as close as possible to where the vent system enters the heated portion of the house.

10¹⁄₈" (25.7 cm)

22" (55.9 cm)

Makeup air

Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area.

Venting Methods

Typical Internal Blower Motor System Venting Installations

A 10" (25.4 cm) round vent system is needed for installation (not included). The hood exhaust opening is 10" (25.4 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance.

Vent system can terminate either through the roof or wall. To vent through the wall, a 90° elbow is needed.

Roof Venting Wall Venting

A. 10" (25.4 cm) round vent B. Roof cap

A. 10" (25.4 cm) round vent B. Wall cap

Typical In-line Blower Motor System Venting Installations

A. 10" (25.4 cm) round vent B. Mount on top of ceiling joists. C. Roof caps D. Plywood (optional for some installations) E. Mount on underside of roof rafters.

F. Mount from cross-members tied to trusses.

G. Duct horizontal; mount to cross-members

tied to trusses.

H. Wall cap

Calculating Vent System Length

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

Vent Piece Equivalent Length

45° elbow 2.5 ft

90° elbow 5.0 ft

(0.8 m)

(1.5 m)

Electrical Requirements

Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

The maximum equivalent vent lengths are: 10" (25.4 cm) round vents - 60 ft (18.3 m)

Example vent system

90 elbow

2 ft

(0.6 m)

6 ft (1.8 m)

The following example falls within the maximum recommended vent length.

1 - 90° elbow = 5.0 ft (1.5 m) 1 - wall cap = 0.0 ft (0.0 m) 8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

Wall cap

INSTALLATION INSTRUCTIONS

Prepare Location

■ It is recommended that the vent system be installed before

hood is installed.

■ Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

■ Hood liner is to be installed 24" (61.0 cm) minimum for

electric cooking surfaces, 30" (76.2 cm) minimum for gas cooking surfaces, to a suggested maximum of 36" (91.4 cm) above the cooking surface.

■ Check that all installation parts have been removed from the

shipping carton.

1. Disconnect power.

2. Determine which venting method to use: roof or wall exhaust.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift hood liner onto covered surface.

5. Remove the filters. See the “Range Hood Care” section.

Hood Liner Support Preparation

1. Mark the locations for the four ¹⁄₈" (3 mm) diameter holes on

the hood support as shown.

A. Wall B. Centerline

C. 6” (15.2 cm)

¹⁄₈

” (25.7 cm)

D. 10

2. Using a ¹⁄₈" (3 mm) drill bit, drill the 4 holes.

E. 14 F. 2 9

¹⁄₈"

diameter

¹⁵⁄₁₆

” (38.0 cm)

¹³⁄₁₆

" (75.8 cm)

(3 mm) hole

3. Mark the cutout for the rectangular clearance hole for the

upper hood liner housing as shown.

A. Wall B. Centerline C. 4

¹⁄₂

” (11.4 cm)

D. 13” (33.0 cm)

E. 14” (35.5 cm)

F. 28” (71.1 cm)

G.Hood support

4. Using a jigsaw or keyhole saw, cut out the rectangular

clearance hole for the upper hood liner housing.

Complete Preparation

1. Determine and make all necessary cuts in the wall or roof for

the vent system. Install the vent system before installing the range hood. See the “Venting Requirements” section.

2. Determine the location where the power supply cable will be

run through the wall.

3. Drill a 1¹⁄₄" (3.2 cm) hole at this location.

4. Pull enough power supply cable through the wall to allow for

easy connection to the terminal box.

5. Install the 10" (25.4 cm) square x 10" (25.4 cm) round vent

transition with damper to top of the range hood liner using four 4.2 x 8 mm screws.

6. Remove terminal box cover and set aside.

7. Remove knockout from the top of the vent hood and install a

UL listed or CSA approved ¹⁄₂" (1.3 cm) strain relief.

8. Place the range hood near its mounting position and run the

power supply cable through the strain relief into terminal box (enough to make connection).

9. Tighten the strain relief screws. NOTE: Your range hood requires you to purchase either an

internal type or an in-line (external type) blower motor system. For internal blower systems, there are blower motor mounting

parts in the blower motor installation packet that must be added to the range hood prior to mounting the range hood to the wall. See the “Install Range Hood Internal Blower Motor” section and the instructions supplied with the blower motor.

Install Range Hood Liner

The hood liner attaches to the hood support using four mounting screws and washers.

NOTE: Hood support must be capable of supporting 75 lb (34 kg).

1. Using 2 or more people, lift the hood liner into place.

2. Install the hood liner using four 5 x 45 mm screws to the hood

support and tighten securely.

Install Hood Liner Internal Blower Motor

NOTE: Your hood liner requires you to purchase either an internal type or an in-line (external type) blower motor system. See “Blower Motor System” in the “Accessories” section.

The internal blower system can be mounted for top venting or rear venting. For top venting, the mounting bracket and spring clip that come with the blower system will mount to the top panel of the hood liner. For rear venting, the mounting bracket and spring clip that come with the blower system will mount to the rear panel of the hood liner.

Prepare the Internal Blower System

IMPORTANT: Perform steps 1-4 before mounting the hood liner.

1. Remove grease filters from hood liner. See the “Range Hood

Care” section in the Use and Care Guide.

2. Install the motor support bracket using three 4.2 x 8 mm

screws. Screw bracket to the inside top or back (alternate location on some models), toward the left side of the hood liner.

3. Install motor spring clip using two 4.2 x 8 mm screws. Screw

spring clip to the inside top or back (alternate location on some models) of the hood liner at the proper location for the selected motor system. Slide the mounting tab of the spring clip through the slot in the panel and secure with the screws. Use the inside set of mounting holes for the single motor system. Use the outside set of mounting holes for the dual motor system.

A. 4.2 x 8 mm screws (3) for motor support bracket B. 4.2 x 8 mm screws (2) for motor spring clip C. Motor support bracket D. Motor spring clip (single motor assembly location)

E. Motor spring clip (dual motor assembly location)

4. Install the 6 mm nuts to the outside top or outside back

(alternate location on some models) of the hood liner at the proper location for the selected motor system.

■ Two 6 mm nuts are required for the single motor system.

Clip nuts into the small square notches located at the left and right end of the square vent opening.

■ Five 6 mm nuts are required for the dual motor system.

Clip nuts into the small square notches, one located in the front of the square vent opening and the other four located at the left and right ends of the square vent opening.

A. Clip nut (6 mm) locations for dual motor assembly (quantity 5)

B. Clip nut (6 mm) locations for single motor assembly (quantity 2)

5. Mount hood liner. See the “Install Range Hood Liner” section.

Install Hood Liner Internal Blower Motor

1. Install the hood liner blower motor assembly inside the hood

liner canopy with the wiring connection to the left for the single motor system and to the front or top for the dual motor system.

Single Blower Motor Assembly

A. Wiring connection

Dual Blower Motor Assembly

3. Run the power supply wires and connector from the range

hood through the hole in the right end of the motor mounting plate.

A. Motor mounting plate hole B. Power supply wires and connector

4. Push the right end of the motor mounting plate up and snap it

into the spring tab. NOTE: The spring tab should be outside the slot in the

mounting plate.

A. Wiring connection

2. Slide the left mounting plate flange under the motor mounting

bracket.

A. Motor mounting bracket B. Mounting plate left flange

A. Motor mounting plate B. Spring clip

5. Align mounting holes in motor mounting plate with motor

mounting clip nuts and install 6 x 16 mm screws and

6.4 mm lock washers (quantity 2 for single motor; quantity 5 for dual motor).

C B

A. Screw with lock washer B. Mounting hole in motor mounting plate C. Clip nut (6 mm)

6. Attach power cord connector from the range hood to

connector on wiring box.

5. Remove the screws that secure the blower motor assembly

to the in-line blower housing and set them aside.

6. Pull the spring clip to release the blower motor assembly.

Remove the blower motor assembly from the housing and place it on a covered surface.

A. Wiring box connector B. Power supply connector

from range hood

7. Go to the “Make Electrical Power Supply Connection to Hood

Liner” section.

Install Hood Liner In-Line (External Type)

Blower Motor

NOTE: Your hood liner requires you to purchase either an internal type or an in-line (external type) blower motor system. See “Blower Motor System” in the “Accessories” section.

Prepare for Mounting the In-Line Blower System

The in-line blower system must be fastened to a secure structure of the roof, ceiling, wall, floor, or new or existing frame construction. The 4 holes on either the inlet (bottom) side or the outlet (top) side of the blower must be used to mount the in-line blower system to the structure.

NOTE: The mounting hole locations must span the studs. Additional stud framing may be required. Plywood may be used to span open areas between ceiling joists or roof rafters to aid installation. This structure must be strong enough to support the weight of the in-line blower system (50 lb [22.6 kg] min).

A. Front cover B. Blower mounting screws C. Spring clip D. Bottom housing mounting holes E. Motor electrical plug

Install In-line Blower System

NOTE: The blower motor housing can be mounted using 4 holes

from either the inlet side or the outlet side of the blower.

Outlet Side

Prepare the In-line Blower System

WARNING

Excessive Weight Hazard

Use two or more people to move and install in-line blower motor system.

Failure to do so can result in back or other injury.

1. Using two or more people, move the in-line blower motor

system to the mounting location.

2. Remove the 10 screws from the front cover of the in-line

blower motor housing and set them aside.

3. Remove the front cover of the in-line blower motor housing

and set it aside.

NOTE: To make the blower motor housing easier to mount, the blower motor assembly can be removed. If you do not want to remove the blower motor assembly, proceed to “Install In-line Blower System” in this section.

4. Disconnect the motor electrical plug from the blower motor

assembly.

Inlet Side

A. Mounting holes

1. Position the in-line blower motor housing in its mounting

location and mark the 4 mounting hole locations.

2. Drill 4 mounting pilot holes using a ³⁄₁₆" (5 mm) drill bit.

3. Attach the in-line blower motor housing to the mounting

location with four 6 x 80 mm mounting screws and washers.

4. If it is removed, reinstall the blower motor assembly and

secure it with the screws previously removed.

5. If it is removed, reattach the motor electrical plug to the

connector on the blower motor assembly.

Complete Preparation

1. Determine and make all necessary cuts for the vent system. IMPORTANT: When cutting or drilling into the ceiling or wall,

do not damage electrical wiring or other hidden utilities.

2. Determine the location where the ¹⁄₂" (1.3 cm) wiring conduit will be routed through the ceiling or wall between the in-line blower and the hood liner.

3. Drill a 1¹⁄₄" (3.2 cm) hole at this location.

4. Locate the electrical terminal boxes in the in-line blower

housing and hood liner. Remove the terminal box covers and set the covers and screws aside.

A. Electrical terminal box B. Electrical knockout

5. Remove the electrical knockout from the in-line blower housing and hood liner to prepare for the installation of the UL listed or CSA approved ¹⁄₂" (1.3 cm) wiring conduit and conduit connector.

6. With the hood liner mounted (see the “Install Hood Liner” section), run the ¹⁄₂" (1.3 cm) wiring conduit between the inline blower motor housing and the hood liner. Pull enough ¹⁄₂" (1.3 cm) wiring conduit to allow for easy connection to the terminal boxes in the in-line blower housing and hood liner.

7. Run the six 18 AWG wires through the ¹⁄₂" (1.3 cm) wiring conduit and conduit connectors and into the terminal boxes on the in-line blower housing and hood liner. Leave enough wire length in each terminal box to make the wiring connections.

8. Install the conduit connectors and conduit to the in-line blower housing and hood liner electrical terminal boxes.

9. Connect the vent system to the hood liner and in-line blower system and seal all joints with clamps.

Make Electrical Connections for In-Line

Blower Motor System

WARNING

Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

Electrical Connection Inside In-line Blower System

1. Disconnect power.

2. Connect the wires from the wiring conduit to the wires from

the motor electrical plug cable inside the in-line blower housing terminal box.

D E F

A. UL listed or CSA approved

¹⁄₂

" (1.3 cm) wiring conduit B. UL listed wire connectors C.Black wires D. White wires E. Red wires

3. Use UL listed wire connectors and connect the black wires

4. Use UL listed wire connectors and connect the white wires

(D) together.

5. Use UL listed wire connectors and connect the red wires (E)

together.

6. Use UL listed wire connectors and connect the blue wires (F)

together.

7. Use UL listed wire connectors and connect the gray wires (G)

together.

F. B lu e wi r es G. Gray wires H. Green (or yellow/green)

and green/yellow wires

I. Motor electrical plug cable

G H

+ 25 hidden pages