Amana Urs511p Service Manual

Microwave Oven Service Manual

RCS10MPA

CAUTION

BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

RS511P RS511MB

RCS511A RFS511G URS511MB URS511P URCS511A RFS511SW2A

RCS10MPSA RFS12MPSA

RFS12G

This device is to be serviced only by properly qualified service personnel. Consult the service manual for proper service procedures to assure continued safety operation and for precautions to be taken to avoid possible exposure to excessive microwave energy.

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

A) Do not operate or allow the oven to be operated with the door open.

B) Make the following safety checks on all ovens to be serviced before activating the magnetron or other

microwave source, and make repairs as necessary; (1) interlock operation, (2) proper door closing, (3)

seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and

latches, (5) evidence of dropping or abuse.

C) Before turning on microwave power for any service test or inspection within the microwave generating

compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,

integrity, and connections.

D) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation

and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual

before the oven is released to the owner.

E) A microwave leakage check to verify compliance with the Federal Performance Standard should be

performed on each oven prior to release to the owner.

SAFETY PRECAUTIONS

(Page)

SAFETY PRECAUTIONS

---------------------------------------------------------------------

Inside front cover

SPECIFICATIONS

-----------------------------------------------------------------------------------------------------

1-1

CAUTIONS

--------------------------------------------------------------------------------------------------------------

2-1

INSTALLATIONS

------------------------------------------------------------------------------------------------------

3-1

OPERATING INSTRUCTIONS

------------------------------------------------------------------------------------

4-1

COOKING DISPLAYS

---------------------------------------------------------------------------------------------------------

4-6

PROGRAMMING DISPLAYS

------------------------------------------------------------------------------------------------

4-6

OPERATION

-----------------------------------------------------------------------------------------------------------------------

4-7

PROGRAMMING

----------------------------------------------------------------------------------------------------------------

4-8

SCHEMATIC DIAGRAM

----------------------------------------------------------------------------------------------------

4-10

CIRCUIT DESCRIPTION

---------------------------------------------------------------------------------------------------

4-11

SERVICE INFORMATION

------------------------------------------------------------------------------------------

5-1

TOOLS AND MEASURING INSTRUMENTS

---------------------------------------------------------------------------

5-1

MICROWAVE LEAKAGE TEST

--------------------------------------------------------------------------------------------

5-1

MEASUREMENT OF MICROWAVE POWER OUTPUT

-----------------------------------------------------------

5-3

DISASSEMBLY AND ADJUSTMENT

-------------------------------------------------------------------------------------

5-3

INTERLOCK CONTINUITY TEST

------------------------------------------------------------------------------------------

5-7

COMPONENT TEST PROCEDURE

--------------------------------------------------------------------------------------

5-8

TROUBLE SHOOTING

------------------------------------------------------------------------------------------------------

5-11

EXPLODED VIEW

-----------------------------------------------------------------------------------------------------

6-1

SCHEMATIC DIAGRAM OF P.C.B.

------------------------------------------------------------------------------

7-1

PRINTED CIRCUIT BOARD

-------------------------------------------------------------------------------------------------

7-2

CONTENTS

1-11-11-11-1

SPECIFICATIONS

Power Requirement

Magnetron

, 0

Power Requirement

Magnetron

, 0

This microwave oven is designed for commercial use only.

It is not recommended for built-in Installation.

ITEM

MODEL

Power Requirement

Power Output

Microwave Frequency

Magnetron

Timer

Outside Dimensions

Cavity Dimensions

Net Weight

Shipping weight

Control Complement

DESCRIPTION

RS511P /

RS511MB

RCS511A / RFS511G

URS511MB

URS511P

URCS511A

RFS511SW2A

230 Volts AC 50 Hz 240 Volts AC 50 Hz 1,60 Watts

Single phase, 3 wire grounded

1,100 Watts full microwave power (IEC 60705)

2,450 MHz

2M282 0 ~ 60 min.

51 lbs (approx.)

58 lbs (approx.)

Touch Control System

Clock : 00 ~ 60

Microwave Power for Variable Cooking

Power level HIGH -------------------------------Full power throughout the cooking time 70% (Med.-High)----------------approx. 70% of Full power 50% (Med.-Low) ---------------approx. 50% of Full power 20% (Low) -----------------------approx. 20% of Full power

Power Requirement

Magnetron

,,,, , 0,1,70 Watts ,,,,,

SPECIFICATIONS

SPECIFICA

Back side

”(W) x 14

”(H) x 17

”(D)

”(W) x 8

” (H) x 16

”(D)

Nameplate Location

¥ DO NOT operate on a 2-wire extension cord during

repair and use.

¥ NEVER TOUCH any oven components or wiring during

operation.

¥ BEFORE TOUCHING any parts of the oven, always

remove the power plug from the outlet.

¥ For about 30 seconds after the oven stops, an electric

charge remains in the high voltage capacitor. When replacing or checking, you must discharge the high voltage capacitor by shorting across the two terminals with an insulated screwdriver.

Remove your watches whenever working close to or

replacing the Magnetron.

¥ DO NOT touch any parts of the control panel circuit. A

resulting static electric discharge may damage this

P.C.B. ¥ NEVER operate the oven with no load. ¥ NEVER injure the door seal and front plate of the oven

cavity. ¥ NEVER put iron tools on the magnetron. ¥ NEVER put anything into the latch hole and the

interlock switches area.

¥ Proper operation of the microwave oven requires that

the magnetron be assembled to the waveguide and cavity. Never operate the magnetron unless it is properly installed.

¥ Be sure that the magnetron gasket is properly

installed around the dome of the tube whenever installing the magnetron.

2-1

CAUTIONS

Unlike other appliances, the microwave oven is high-voltage and high-current equipment. Though it is free from danger in ordinary use, extreme care should be taken during repair.

THE OVEN IS TO BE SERVICED ONLY BY PROPERLY QUALIFIED SERVICE PERSONNEL.

MICROWAVE RADIATION

Personnel should not be exposed to the microwave energy which may radiate from the magnetron or other microwave generating device if it is improperly used or connection. All input and output microwave connections, waveguide, flange, and gasket must be secure never operate the device without a microwave energy absorbing load attached. Never look into an open waveguide or antenna while the device is energized.

Gasket

ANTENNA

COOLING FIN

MAGNETRON CHASSIS GROUND

FILAMENT TERMINALS

MAGNETRON

INSTALLATIONS

3-1

BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.

INSTALLING

1. Empty the microwave oven and clean inside it with

a soft, damp cloth. Check for damage such as misaligned door, damage around the door or dents inside the cavity or on the exterior.

2. Put the oven on a counter, table, or shelf that is

strong enough to hold the oven and the food and utensils you put in it. (The control panel side of the oven is the heavy side. Use care when handling.)

3. Do not block the vent and the air intake openings.

Blocking vent or air intake openings can cause damage to the oven and poor cooking results. Make sure the microwave oven legs are in place to ensure proper air flow.

4. The oven should not be installed in any area where

heat and steam are generated, because they may damage the electronic or mechanical parts of the unit. Do not install the oven next to a conventional surface unit or above a conventional wall oven.

5. Use microwave oven in an ambient temperature

less than 104°F(40°C).

EARTHING INSTRUCTIONS

This microwave oven is designed to be used in a fully earthed condition. It is imperative, therefore, to make sure it is properly earthed before servicing

WARNINGTHIS APPLIANCE MUST BE EARTHED

IMPORTANT

The wires in this mains lead are colored in accordance with the following code:

Green-and-yellow: Earth Blue: Neutral Brown: Live

As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug, proceed as follows.

6. Place the microwave oven on a sturdy and flat

surface at least 10 cm(4 inches) from the wall.

7. Place the microwave oven as far away as possible

from TV, RADIO, COMPUTER, etc., to prevent interference.

8. Do not touch the front glass during or after cooking

of the Grill and Combination mode. This glass is very hot during heater operating.

9. Do not operate the oven at microwave and

combination mode with Grill rack placed in the cavity when the oven is empty.

10cm

The wire which is colored green-and-yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol ( ) or colored green or green-and-yellow.

The wire which is colored blue must be connected to the terminal in the plug which is marked with the letter N or colored black.

The wire which is colored brown must be connected to the terminal in the plug which is marked with the letter L or colored red.

4-1

FEATURES

Window Door Screen

Electronic Control

Safety Door Lock System

CONTROL PANEL

Display

Some items in display can be seen but will not glow.

Pads

TIME ENTRY

Pads 1-0

HOLD 0%, DEFROST 20%, MEDUIM 50%, MED-HI 70%

STOP/RESET

START

Use to enter heating time without changing preprogrammed number pads.

Use to begin heating with preprogrammed times and power levels or to enter times for “Manual Time Entry” cooking.

Use to select power level. Oven can heat at full or reduced power. If oven power level is set to 0% oven does not heat for programmed time. If no power level is selected, oven operates at 100% power.

Use to exit programming mode and stop cooking during cooking cycle.

Use to start “Manual Time Entry” program or restart interrupted cooking cycle. Use to advance to next user option. Use to save times and power levels when programming pads.

RS511P / URS511P

4-2

FEATURES

Window Door Screen

Electronic Control

Safety Door Lock System

CONTROL PANEL

Display

Some items in display can be seen but will not glow.

Pads

TIME ENTRY

Pads 1-0

POWER LEVEL

STOP/RESET

START

QTY2x

Use to enter heating time without changing preprogrammed number pads.

Use to begin heating with preprogrammed times and power levels or to enter times for “Manual Time Entry” cooking.

Use to select power level. Oven can heat at full or reduced power. If oven power level is set to 0% oven does not heat for programmed time. If no power level is selected, oven operates at 100% power.

Use to exit programming mode and stop cooking during cooking cycle.

Use to start “Manual Time Entry” program or restart interrupted cooking cycle. Use to advance to next user option. Use to save times and power levels when programming pads.

Use to automatically increase the programmed time for double quantities.

RCS511A / URCS511A

4-3

FEATURES

Window Door Screen

Electronic Control

Safety Door Lock System

CONTROL PANEL

Display

Some items in display can be seen but will not glow.

Pads

DIAL

QUICK SET

70%,

50%,

DEFROST

START

Use to enter cooking time.

Use to begin heating with preprogrammed times and power levels.

Use to select power level. Oven can heat at full or reduced power.

Use to start “Manual Time Entry” program or restart interrupted cooking cycle. Use to advance to next user option. Use to save times and power levels when programming pads.

RCS511MB / URS511MB

4-4

FEATURES

Window Door Screen

Electronic Control

Safety Door Lock System

CONTROL PANEL

Display

Some items in display can be seen but will not glow.

Pads

TIME ENTRY

Pads 1-0

HOLD 0%, DEFROST 20%, MEDUIM 50%, MED-HI 70%

STOP/RESET

START

Use to enter heating time without changing preprogrammed number pads.

Use to begin heating with preprogrammed times and power levels or to enter times for “Manual Time Entry” cooking.

Use to select power level. Oven can heat at full or reduced power. If oven power level is set to 0% oven does not heat for programmed time. If no power level is selected, oven operates at 100% power.

Use to exit programming mode and stop cooking during cooking cycle.

Use to start “Manual Time Entry” program or restart interrupted cooking cycle. Use to advance to next user option. Use to save times and power levels when programming pads.

RFS511SW2A

4-5

OPERATING INSTRUCTIONS

FEATURES

CONTROL PANEL

Display

Some items in display can be seen but will not glow.

Pads

Use to enter heating time without changing preprogrammed number pads.

Use to begin heating with preprogrammed

Use to enter times for “Manual Time Entry”

times and power levels or to enter times for “Manual Time Entry” cooking.

cooking.

Use to select power level. Oven can heat at full or reduced power. If oven power level is set to 0% oven does not heat for programmed time. If no power level is selected, oven operates at 100% power.

Use to exit programming mode and stop cooking during cooking cycle.

Use to start “Manual Time Entry” program

Use to automatically increase the programmed time for double quantities.

or restart interrupted cooking cycle. Use to advance to next user option. Use to save times and power levels when programming pads.

RFS511G

TIME ENTRY

DIAL

Pads 1-0

POWER LEVEL

STOP/RESET

START

QTY2x

8 9 0

Window Door Screen

Electronic Control

Safety Door Lock System

POWER

LEVEL

QTY

TIME

ENTRY

4-6

Cooking Displays

Shows when power is connected to oven. Open and close door to clear.

READY shows when oven control will accept entries. Appears after oven door is opened and closed.

33:33 shows heating time. When more than 1 heating stage is programmed, total time for all stages displays.

COOK shows when oven is operating. 20 indicates the microwave power level used. If power level

does not show, oven is heating at 100% power.

Cooking DisplaysCooking DisplaysCooking Displays

Programming Displays

Indicates programming mode. See “Programming” section of manual for programming procedure.

Indicates programming user options mode. See “User Options” section of manual for programming procedure.

Programming DisplaysProgramming DisplaysProgramming Displays

4-7

Operation

Pads

1 2 3 4 5 6 7 8 9 0

Heating Times

10 sec. 20 sec. 30 sec. 45 sec. 1 min. 1:30 min. 2 min. 3 min. 4 min. 5 min.

Pads

01 02 03 04 05 06 07 08 09 10

1. Press Pad.

CAUTION

Interrupting Operation

• Open oven door to interrupt operation. Oven fan continues to operate. Close door and press START pad to resume oven operation.

• Press STOP/RESET pad to interrupt operation. Display continues to show countdown time. Press START pad to resume oven operation and countdown timing.

Canceling Mistakes

• If oven is operating, press STOP/RESET pad once to

stop oven, then again to clear display.

• If oven door is open and time shows in display, close oven door and press STOP/RESET pad to clear display.

Operating Preprogrammed Pads

Oven has 10 ~ 20 preprogrammed number pads. Instructions are written for factory programmed ovens. Ovens that are reprogrammed can respond differently than described below.

1. Open oven door , place food in oven, and close oven

door

• If pad is not pressed in 30 seconds, open and close oven door again.

2. Press desired number pad.

• Oven operates and time counts down.

3. Oven stops heating and oven signal sounds when heating timing elapses.

Operating QTY 2X Pads

QTY

2. Press desired number pad

• Example : press + = 18 sec.

Preprogrammed Times and Cook Level

All preprogrammed pads arrive set at full power.

Option: Single Digit

Pads

11 12 13 14 15 16 17 18 19 20

Heating Times

10 sec. 20 sec. 30 sec. 45 sec. 1 min. 1:30 min. 2 min. 3 min. 4 min. 5 min.

Heating Times

20 sec. 40 sec. 1 min. 1:30 min. 2 min. 3 min. 4 min. 6 min. 8 min. 10 min.

Option: Double Digit

Manual Time Entry

Manual Time Entry feature allows the operator to enter time and power levels, and heat without changing the preprogrammed pads.

1. Open oven door, place food in oven, and close door.

• Display shows "READY".

• If pad is not pressed in 30 seconds, open and close oven door again.

2. Press TIME ENTRY pad.

• Display shows "00:00".

3. Press number pads to enter desired cooking time.

• For example, to heat for 2 minutes 30 seconds,

press 2, 3, and 0 pads.

4. Press desired power level pad to change power level.

• If a power level pad is not pressed, oven defaults to 100% power.

• For example, pressing MEDIUM 50% pad sets oven to 50% power.

• Display shows current power level if other than 100 percent power.

5. Press START pad.

• Oven operates and time counts down.

6. Oven stops heating and oven signal sounds when heating timing elapses.

QTY

To avoid fire, do not dry newspapers or clothes in microwave oven.

4-8

PROGRAMMING

Preprogrammed Number Pads

Oven has 10 preprogrammed number pads. Follow instructions below to program heating times and power levels for customized cooking.

1. Open oven door. ¥ If door is closed or STOP/RESET pad is pressed

before finishing programming sequence, oven exits programming mode.

2. Press and hold pad 1 for approximately 5 seconds. ¥ After 5 seconds, signal sounds. Display shows

ÒPROGRAMÓ indicating program mode..

3. Press desired number pad. ¥ Display shows heating time, ÒCOOK LEVELÓ and

power level if other than 100 percent power.

4. Press number pads to enter desired cooking time. ¥ For example, to heat for 2 minutes 30 seconds,

press 2, 3, and 0 pads.

5. Press desired power level pad to change power level. ¥ If a power level pad is not pressed, oven defaults to

100% power.

¥ For example, pressing MEDIUM 50% pad sets oven

to 50% power.

¥ Display shows current power level if other than 100%

power.

6. Press START pad to save new heating time and power level in oven memory. ¥ Repeat step 3-6 to program additional pads.

7. Press STOP/RESET pad or close oven door to exit programming mode.

Multiple Heating Stages

Follow instructions below to program oven to perform 3 consecutive heating cycles without interruption.

1. Open oven door. ¥ If door is closed or STOP/RESET pad is pressed

before finishing programming sequence, oven exits programming mode.

2. Press pad 1 for approximately 5 seconds. ¥ After 5 seconds, signal sounds.

3. Press desired number pad. ¥ Display shows heating time and preprogrammed

number.

4. Press number pads to enter desired cooking time. ¥ For example, to heat for 2 minutes 30 seconds,

5. Press desired power level pad to change power level. ¥ If a power level pad is not pressed, oven defaults to

100% power.

¥ For example, pressing MEDIUM 50% pad sets oven

to 50% power.

¥ Display shows current power level if other than 100

percent power.

6. Press TIME ENTRY pad ¥ Display briefly shows ÒSTAGE 2Ó . Then cook time

and power level for stage show in display.

¥ Repeat steps 5-6 to create additional stages.

7. Press START pad to save new heating time and power level in oven memory.

8. Press STOP/RESET pad or close oven door to exit programming mode.

+ 31 hidden pages