Amana NAV6800AWW, NAV5800AWW, NAV3330AWW, NAV2330AWW Installation Guide

BUILT BETTER THAN IT HAS TO BE"

Installation
Instructions

Top Loading Washer

Keep instructions for future reference. Be sure manual stays with washer.

MOVE WASHER
TO FINAL AREA;

REMOVE
SHIPPING BRACE

& PLUG

Protect the floor when moving the

washer. Washer must be within 4 feet

of desired area before beginning
installation. Open washer lid and
remove installation parts from
shipping brace for use.

Reach through foam shipping
brace, grasp bottom of brace, and
pull up to remove.

i

CONNECT

WATER FILL

HOSES TO

WASHER

Tightly push one flat rubber
washer into one end of each

water fill hose and attach this end
of hose to washer. HOT and

COLD connections are identified
by letters H and C stamped into

washer cabinet and by HOT and
COLD printed on water fill hoses.

NOTE: Save shipping plug and

shipping brace; reinstall whenever
washer is moved more than 4 feet.

Do not lift or move washer without

shipping materials in place.
To remove the shipping plugfrom the

washer, step on the card board base,
tilt the washer back, and slide out the
base.

i

In most cases, hoses should
cross when attached to correct

water temperature faucet.
]]ghten hose connections by hand

until snug, then another ¼ turnwith
pliers. DO NOT cross-thread or over-
tighten couplings.

Cardboard

base

Shipping

brace

Shipping

plug

end of fill hose.

i¸¸ i

r _ CONNECT Tightly push one screened filter _-

/ Jr ..,,,_.---, ...__ washer onto remaining end of each , J .-

/ _ lflf,_ I "K rill. water fill hose. Attach water hoses to __ _ faucets
/ HOSES TO HOT and COLD faucets. BE SURE JJHOT ,__

] FAUCETS HOT WATER HOSE IS CONNECTED _ __J _._K j

/ ...... TO HOT WATER FAUCET. _ / _'_j

/ Before connecting hoses to water _ i OLD_

| supply, turn on faucets and flush Tighten hose connections by hand ( _

| lines for approximately 2 minutes until snug, then another '/_turn with I_ |
/ to remove foreign matter that could pliers. DO NOT cross-thread or over- I_1 -- -

/ clog filter screens in water mixing tighten couplings. ,,

valve orfill hoses. . ..... L_ _ I) Screen Filters

/ Turn on water ane cnecK tor leaKs.
/ -- _ If leaks are found retighten hose _

| _ couplings. Continue tighteningand I_ 'i'
| lil} rechecking until no leaks are found. L_J

[ / " • H°'el

SECURE DRAIN

HOSE TO DRAIN

Remove drain hose from shipping
position on rear of washer by

unhooking hose from retainer
clamp. Use beaded tie-down
strap to secure "hook" end of drain

hose to standpipe, wall inlet hoses,
or laundry tub (must hold at least 20
gallons).

IMPORTANT: To prevent siphoning,
do not place ribbed portion of drain
hose intostandpipe. Avoid air-tight
seal around standpipe adapter.

For standpipe installation below 36"

(91.4 cm), install Siphon Break Kit
part #562P3.

For standpipe installation above 48"
(121.2 cm), install a check valve to

prevent water from flowing back
into washer. Available from local

hardware store.

36" (min)
from floor

.... LA_

72" (max)
36" (min)

from floor

Standpipe Wall Unit

Beaded

Standpipe tie-down

_ adapter strap_L

(avoid

air-tight seal)

_. Beaded

de-down
strap

36" (min)
from floor

Tub

Beaded

de-down

strap