Amana GB2026LEKS, GB2526PEKW, GB2225PEKW, GB2026REKS, GB2026PEKW Owner’s Manual

...

mBottom

Freeze

Refri

U$¢

Important Safety Instructions ....................... 1=2

InstallatioB ....................................... 3=6

Temperature Controls ................................ 7

Fresh Food Features .............................. 8=10

Freezer Features ................................... 11

Food Storage Tips .................................. 12

Care and Cleaning ............................... 13=16

_] Operating Sounds .................................. 17

li_ Troubleshooting ................................. 18-20

Part No. 12828148 Litho LISA

ImportentSefety

hlsl_ller: Please leave thin guide with thB appliance. Consumer: Please read and keep this Use & Care

Guide for future reference. This guide provides proper use and maintenance reformation.

Keep sales receipt and/or cancelled check as proof of purchase.

Have complete model and serial number identification of your refrigerator. ThB is located on a data plate reside tile refngerator compartment, on

the upper left side. Record these numbers below for easy access.

Model Number Senal Number

Date of Purchase In OLIr continuing effort to mlprove tile quality and

performance of our apphances, it may be necessary to make changes to tile apphance without revising thin guide.

What You Need to Know About Safety Instructions

Warning and Iml)ortant Safety Instructions appeanng in this guide are not meant to cover all possfl]le

conditions and s_tuat_ons that may occur. Common sense, caution and care illUSt be exercised when

mstalhng, maintaining or operating apphance. Always contact tile manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

DANGER - Immediate hazards which WiLL result m severe personal injury or death.

WARNING - Hazards or unsafe practices whlcll COULD result m severe personal injury or death.

CAUTION - Hazards or unsafe practices which COULD result m minor personal injury or property damage.

To reduce risk of injury or death, follow basic precautions, including the following:

Important: Junked or abandoned refrigerators are still dangerous - even if they sit out for "just a few

days" If you are getting nd of your old refrigerator, please follow the instructions below to help prevent

accidents. Before you throw away your old

refrigerator or freezer:

• Take off the doors. , Leave the shelves m place so

children may not easily chmb reside.

ImporlenlSefelyInstrucllons

To reduce risk of fire, electric shock, serious injury 13. install refrigerator according to Installation or death when using your refrigerator, follow these

basic precautions, including the following:

1 Read all instructions before using the refrigerator.

2 Observe all local codes and ordinances

3. Be sure to follow earthmg instructions 4 Check with a qualified electrician if you are not sure

this apphance is properly earthed

5 Do not earth to a gas line 15

6. Do not earth to a cold-water pipe

7 Refrigerator is designed to operate on a separate

220-240 volt, 10 amp., 50 HZ cycle line

8 Do not modify plug on power cord If plug does not 17

fit electrical outlet, have proper outlet installed by a quahfled electrician

9 Do not use a two-prong adapter, extension cord or

power strip 19

10. Do not tamper with refrigerator controls

]]

Do not service or replace any part of refrigerator unless specifically recommended in Use & Care

Guide or pubhshed user-repair instructions. Do not attempt service if instructions are not understood or if they are beyond personal skill level

Instructions All connections for water, electrical power and earthing must comply with local codes

and be made by licensed personnel when required.

Keep your refrigerator in good condition Bumping or dropping refrigerator can damage refrigerator or

cause refrigerator to malfuncbon or leak If damage occurs, have refrigerator checked by qualified

serv,ce technician A qualified service technician must replace worn

power cords and/or loose plugs

Always read and follow manufacturer's storage and ideal environment instructions for iterns being stored in refrigerator

Your refrigerator should not be operated m the presence of explosive fumes

Children should not chmb, hang or stand on any part of the refrigerator

Clean up spills or water leakage associated w=th water installation

20 The appliance is not intended for use by young

children or infirm persons w,thout supervision.

21 Young children should be supervBed to ensure that

they do not play with the appliance

12 Always disconnect refrigerator from electrical supply

before attempting any service Disconnect power cord by grasping the plug, not the cord

installing Your Refrigerator

These instructions were provided to aid you in the installation of your unit. The i]lal]ufacturer cannot be resl)onsible for improper installation.

Steps to Follow...

A qualified engineer must connect refrigerator in accordance with these installation instructions.

Measure door opening and depth and width of refrigerator. Remove handles or doors if requued. Engineer mLISt also do the following:

1. Follow local water and electrical coml)any connection regulations.

2. Complete water supply connection before electrical supply connections.

Service to or replacement of power cord must be performed by a qualified engineer.

Note:

When writing or calhng abou[ a serwce problem, please mchide the following mforma[ion

a Your name, address and telephone number, d A clear descrq)bon of the problem you are hawng, b Model numl)er and serial number, e Proof of purchase [sales receq)[) c Name and address of your dealer or engineer,

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

Yourrefrigeratorwaspackedcarefullyforshipment. Removeanddiscardshelfpackagingandtape.Do not

remove the serial plate.

Measuring the Opening

When installing your refrigerator, measure carefully. 1.3 cm (_"} of air space should be provided for the top and back of the refrigerator.

Location

• Do not install refrigerator near oven, radiator or

other heat source. If not possible, shield refrigerator

with cabinet material.

• Do not install where temperature falls below 13° C or rises above 95° C. Malfunction may occur at this

temperature.

• Refrigerator is designed for indoor household application only.

How to Remove and Replace

60 cm deep models

Note: Trim corners of countertop to a 45° angle if countertop has 25 mm overhang. Provide 5 mm clearance on both sides of refrigerator, and allow 7 mm on top for ease of installation and leveling. No minimum clearance is required at the rear of the

cabinet.

Subflooring or floor coverings (i.e. carpet, tile, wood floors, rugs} may make your opening smaller than

anticipated. Some clearance may be gained by using the leveling

procedure under Leveling. Important: If refrigerator is to be installed into a

recess where the top of the refrigerator is completely covered, use dimensions from floor to top of hinge cap

to verify proper clearance.

Transporting Your Refrigerator

• NEVER transport refrigerator on its side. If an

upright position is not possible, lay refrigerator on its back. Allow refrigerator to sit upright for approximately 30 minutes before plugging it in to assure oil returns to the compressor. Plugging the refrigerator in immediately may cause damage to

internal parts. Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back-NEVER from its front.

• Protect outside finish of refrigerator during transport by wrapping cabinet in blankets or inserting padding between the refrigerator and dolly.

Door and Hinges

How to Connect the Water

Supply (select models)

Leveling

To enhance the appearance and maintain performance, the refrigerator should be level. (side to side}

Notes:

• Complete any required water supply connection

before leveling.

• Some models only have adjustment screws I:A:}.

Materials Needed:

• 3/8"hex head driver

• Carpenter's level

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when possible. Do not over-tighten. Over-tightening

restraints may dent or damage outside finish.

1. Remove toe grille.

• Grasp firmly and pull outward to unclip.

2.Usinghexheaddriver,turnthefront adjustment screws(A) oneachsideto raiseor lowerthefront

oftherefrigerator.

C C

3. Select models also have rear adjustment screws (B). Using the hex head driver, turn each of these adjustment screws (B) to raise or lower the rear of

the refrigerator.

4. Using the carpenter's level, make sure front of

refrigerator is 6 mm or approximately one half bubble higher than back of refrigerator and that

the refrigerator is level from side to side.

5. Turn stabilizing legs (C) clockwise until firmly against floor.

6. Freezer drawer models only: Turn adjustment

screws [A) counterclockwise to allow the full weight of the refrigerator to rest on the

stabilizing legs.

Fresh Food Handles

Front Mount Handle - Style 1

Materials Needed: * Phillips screwdriver

* 5A6"hex head driver To install:

1. Remove 0.6 cm hex head screws from door face with hex head driver, and Phillips screw from top of door.

* If reversing door, remove door plugs

from opposite side of door and insert in screw holes.

2. Align handle holes with screw holes on door face and secure with two door face

screws from step 1.

3. Locate handle trim in literature pack and install over top and bottom of handle, as

illustrated. * Secure top handle trim with remaining

screw removed in step 1.

7. Replace the toe grille. * Align the toe grille mounting clips with the lower

cabinet slots.

* Snap bottom portion into place first. Press

down on top of grille until top portion snaps into place.

For pullout drawer only:

1. Turn both stabilizing legs clockwise until

firmly against floor.

Turn roller adjustment screws 2

to 3 times counterclockwise so that the full weight of refrigerator rests on stabilizing legs.

2. Replace toe grille. See markings on inside of toe

grille to insure proper placement.

RollerAdjustmeni Screw

!@ Stabilizing

.- Leg

Handles

If not installed, the handle is located in the interior of

the fresh food section or attached to the back of your

refrigerator.

* Snap bottom trim over bottom portion

of handle.

To Remove:

1. Remove top handle trim by removing top handle screw.

* Retain trim and screw for later

replacement.

2. Pry bottom handle trim from handle with screwdriver flat blade wrapped in

masking tape. * Retain trim for later replacement.

3. Remove two hex head screws.

Retain screws for later replacement.

Side Mount Handle Materials Needed:

* Phillips screwdriver To install:

Remove and discard handle packaging and tape. Handle design varies from refrigerator to refrigerator.

Please reference the appropriate instructions for your model below.

1. Remove screws from the side of the door.

2. Align the side mount handle with the pre-drilled holes in the door panel.

3nsertthescrewsnthesequenceaSshownJ

Upper _'_.. 2

Handle

To Install:

1. The handles are to be oriented as shown.

Lower

%d,e

4. Ensure the door handle is snug to the door panel.

To Remove:

Reverse installation procedure.

Freezer Handles

Partial-Width Handle

Materials Needed:

• Phillips screwdriver

To install:

1. Install handle by fastening with

screws removed from edge of door.

• If reversing freezer door, remove

door plugs from top edge of door and insert into screw holes.

To Remove: _

2. Align door handle clip with the door studs.

3. Ensure the large hole in the mounting clip is positioned

down on both ends of the handle.

Stud

4. Rotate the handle so that the handle is flat against the door.

5. Grasp the handle firmly and slide down.

1. Remove handle screws with Phillips screwdriver and retain screws for

later use.

Front Mount Handle - Style 2 Materials Needed:

• Gloves to protect hands

Attach Extensions to Handle: [select models)

1. Align handle and extension as shown.

2. Place extension in handle opening.

3. Apply slight pressure _ to both sides of the extension piece.

4. Slide extension until it stops on inside edge of handle.

To Remove:

1. Grasp the lower part of the handle firmly, slide up, lift and remove from

the surface.

Front Mount Freezer Handle

Materials Needed:

• Gloves to protect hands.

Notes:

• There is a slight curve to

this style of freezer

handle.

• For proper installation, be _o.:,,,s_s_..................................................................

sure handle is oriented as shown.

To install:

1. Align drawer handle clips to the left of the studs attached to the freezer drawer.

2. Ensure the large hole in the mounting clip is positioned to the right on both ends of the handle.

3. Rotate the handle so the left base is flat against the door.

4. Grasp the handle firmly and slide handle to the right.

Handle Door

Cli

To Remove:

Opening and Closing Your

Fresh Food Doors (selectmodels)

Your new refrigerator is uniquely designed with two fresh food doors.

Either door can be opened or closed independently of one another.

There is a vertically-hinged section on the left fresh food door. When

the left door is closed, the hinged section automatically forms a seal

between the two doors when both

doors are closed. When the left door is opened, the hinged seal

automatically folds inward so that it is out of the way.

1. With both hands, firmly grasp the handle toward the right side.

2. Slide toward the left, lift and remove from the surface.

Handle Removal

Euro Handles

This handle style is installed at the factory

NlateriaJs Needed:

• 3/32"Allen wrench

To Remove:

• Remove set screw from handle mounting post using 3/3,,Allen

wrench.

• Repeat the procedure on all posts

to remove the handle.

How to Connect the Water

Supply [select models)

ice Maker Operation

• To turn ice maker On push arm down from locked position.

• Lift arm up and lock into position to turn ice maker Off.

To Replace:

• Align handle with the mounting posts.

• Fully tighten all set screws to secure handle in place.

+ 16 hidden pages